Compaq starts on pluging power indicates red signal and stops few second

I called Chicago base with a similar problem and they said send it in...Was an internal problem

A continuous flashing red light with the word LAMP on it would definitely mean you're going to need to spend a few bucks on a new lamp....or for a few more, upgrade to a TV from this century that doesn't require lamp changes :)

If all the keys on the keyboard have stopped functioning follow the instructions below to reconnect the keyboard.

This problem is likely to be a lost connection. The connection between the mouse and the USB mini-receiver or the keyboard and the USB mini-receiver can be lost due to several reasons such as:

• Low batteries
• Moving the USB mini-receiver from one USB port to another
• Moving the USB mini-receiver to another computer
• Plugging the USB mini-receiver into a USB hub or other unsupported device such as a KVM switch (your USB mini-receiver must be plugged directly into your computer)
• Using your cordless mouse/keyboard on metal surfaces
• Radio frequency (RF) interference of more powerful wireless devices such as:
  • Wireless speakers
  • Computer power supplies
  • Monitors
  • Cellular telephones
  • Garage door openers

Eliminate any problem sources mentioned above that might be affecting your devices.

Follow the procedures below to reconnect your mouse and keyboard.

1. Make sure the USB mini-receiver is directly and securely plugged into a working USB port on your computer.
   
2. Make sure the mouse is turned on. The on/off indicator on the bottom of the mouse should be green. If the on/off indicator is not illuminated, press and hold the red connect button on the bottom of the mouse until the on/off indicator is green.
   On / Off Indicator
   
   
3. Press and release the red connect button on the underside of the USB mini-receiver. This will broadcast a signal to your mouse. This broadcast will last only a few seconds, so you must perform the next step quickly.
   
   Red Connect Button
   
4. Quickly press the red connect button on the bottom of the mouse for 1 second, then release it. The power indicator will flash briefly and then turn green. The mouse is now connected to the receiver.
   
   Red Connect Button NOTE: Holding down the red button on the mouse for more than 2 seconds may cause your mouse to turn off instead of connecting. If this occurs, start again at step number 2.
   
5. Move your mouse to see if the cursor moves. If the cursor follows the mouse movements, your mouse is now connected.
   
6. Press and release the red connect button on the underside of the USB mini-receiver. This will broadcast a signal to your keyboard. This broadcast will last only a few seconds, so you must perform the next step quickly.
   
   Red Connect Button
   
7. Quickly press and release the red connect button on the underside of the keyboard.
   Keyboard Connect Button
   
8. You will hear a short beep. The keyboard is now connected to the receiver.
   
9. Test your keyboard to see if it is working. If the mouse now works but the keyboard still does not, see Knowledge Base article 9144.
   

hi buddyd56

press and hold the power button for up to 15 seconds...the 6000T 3000T and the 3050 all require you to hold the power button for up to 15 second if its in the off position or the battery is dead.. most all other magellan gps will start within 7 seconds if the battery is totally drain or its in the off position.


let me know if that doesnt wok, but it works if there
is no damage to the gps like a bad screen ect


good luck

bill

We are having the exact same problem. Would really be interested to know if it could be repaired at reasonable cost.

you may need to replace the battery inside the controler

If the front power light is blinking three times then your TV has a problem with the convergence. You can get the correct replacement parts and full step by step photo instructions from www.TvRepairKits.com

power in the tv has nothing related with the DVD. The tv has to have raster (white screen) even without signal (cable, DVD, others) if the tv alone is just having the led flashing and neither sound nor video (black screen) The tv has a short circuit in some of the boards that are part of the tv system. the blinking is part of a protection when the tv was created in the factory. Refer to the technician to repair this problem.

Hey,

Test your charger, the battery light blinking and the computer not starting up indicates not enough power to start up or not pluged into ac power, check the power adapter or charger. I suspect the battery is fine.

Thanks,
Ekse

Hi,
F-9 error code indicates a defective control board, inverter or line voltage too high. f the microwave runs for about 7 seconds with a ticking sound..then stops and shows "F-9", it is the magnetron that has failed. The fact that the unit starts and runs with the TICKING SOUND means the control board is sending signal to inverter board and the inverter board is sending signal to magnetron. Magnetron is covered by full 5 year warranty, inverter board is only 3 years.