Need new canopy top for model LP-70008

talk with an upholsterer and get a new one made

Google is amazingly good at calculations. Just go to Google and put in what you want to know, in this case: 1 ft 7 in x 8ft x 3 ft 9 in gallons

I’m happy to help further over the phone at https://www.6ya.com/expert/donald_f2ed37026a3ac881

Roy, replacement canopy,Check the attached links. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
https://www.gardenwindscanada.com/replacement-gazebo-canopy-c-83.html?gclid=CLWdx86LkcwCFYSAaQod-jgKDg

https://www.lowes.ca/outdoor/sheds-outdoor-structures/gazebos

The Home Depot Patio 10 ft 10 ft Replacement Gazebo Cover The Home Depot...

SunjoyDirect com Replacement Replacement Canopies Browse

And why is this posted under sewing machines?

If you only changed the gas regulator for use with LP (the regulator located at the connection of the gas service) then you still need to change the orifices for all burners, top and oven. Of course I assume this model can be converted for use with LP. Some models cannot. A new range that can be converted for LP typically includes the needed LP orifices. A card with the LP orifices is typically located at the gas regulator.

Some panels can't be removed from the back but from the Top and Front only. Check the Front and the Top

A javelin should be between 2.6 m (8 ft 2 in) and 2.7 (8ft 10in) in length for men and between 2.2 and 2.3 m (7 ft 3 in and 7 ft 7 in) in length for a woman

How to set up an Ozark Trail 11ft X 8ft Dining Canopy
It is best to have two people assemble this.

Rods:
4 Side Gables: 2, 2b
3 Rafters Across: 1, 1b. 1b
4 Legs: 1, 1B & 3B

The pieces were not labeled so I used a label maker and permanent marker to label the rods and connectors. The plastic connectors do label the legs and gables but don't label the rafters.


1.Connect a 2 and 2b rod to create a Side Gable. Repeat with the other three 2 and 2b rods.
2.Insert the four Side Gables into the two unmarked connectors (written with a G) to make the pitch of the roof.
3.Connect a 1 rod with two 1b rods to create a Rafter. Repeat to create two more rafters.
4.Insert two Rafters into the 4 corner connectors (written with an R) to form a rectangle frame.
5.Insert the last Rafter in the center connectors to support the peak of the roof.
6.Connect a 1 with two 1b rods to create a leg and repeat to complete the four legs.
7.Inset the legs into the four corner connectors (written with an L).
8.Place the canopy on the frame and use the Velcro tabs on each end to secure in place.
9.Place the hooks (attached to ropes hanging from D Rings) into the appropriate hole on the legs to keep it tight.
10.Stake the canopy to avoid it blowing away.

When assembling alone, put the leg segments into the plastic connectors; pull the canopy over the short frame, then walk around to add the additional leg pieces.

That's 9.25 ft by 8.33 ft = 77.05 sq ft. I plugged that in at onlineconversion.com and got 77.05 square foot = 7.158 179 232 square meter (or 7.16 sq meters)

NO! that unit will NEVER reach 30*f cold.The refergerant used does not run(operate) that cold.