Question about Lanier Office Equipment & Supplies

Open Question

What do i do if the control panel is not functioning when you put on the lanier ld115 copier?

When you on the main switch, the machine is quite on but when you press like the button to increase the the quality of the image, it is not acting and when you start copying the screen and the control panel goes off while the machine is still on.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 214 Answers

SOURCE: Dead touch screen

did you try to turn the brightness button.

Posted on Jun 19, 2008

Ad
  • 126 Answers

SOURCE: IMAGE TOO DARK ON GEI GRAPHIC ZOOMER POSTER BANNER SYSTEM

First I would give the optical area a good cleaning --- mirrors, lens, etc.. If this device has the 'slide' adjust for the image quality, the slide may have come out of the holder. Try seeming if the slide is seated properly. If this is the 'thumb / circle ' adjust, the POT ( value adjust on the board) may need to be reset. There is always the chance the the board is cracked or has a cold solider joint (pins) for the adjuster. IF you are inclined, that the cover off and check for crack, if no crack heat and re-solider the pins for the adjust switch.

Posted on Jan 04, 2009

angelus316
  • 41 Answers

SOURCE: I have a Lanier 5245. I am getting an error when

Your duplex is the big box on the right side of the machine push the back side shut against the machine and try again

Posted on May 22, 2009

  • 422 Answers

SOURCE: lanier 6725 copier: Paper is always jamming and

I have worked for Lanier for 20 years, the 6725 was a great machine, but getting parts, spending $$$ and still having an old copier. Lanier is owned by Ricoh and all machines are Ricoh with a Lanier sticker on it. Its time.
-Carl, please let me know if this helps.

Posted on Jun 26, 2009

crystalco43503
  • 1 Answer

SOURCE: copier gets ready, E000530-0000 is coming back again

error code e000530-000 moder ir3300 canon

Posted on Dec 31, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have LANIER LD115 Copier/ printer can not copy and print ,red light showen on copy button,Erro shown " SC: 544" AND " CALL SERIVCES" , GREEN Light on copy indicator, red on printer light, shown up


The copier error code SC544 / 544 is a fusing lamp overheat error code. (This is a hardware problem)

This error can mean the:
PSU board is bad
IOB board is bad
BICU board is bad
Defective thermistor in the fuser
Defective power supply

You need to contact a local service technician to take a look at your copier.

Nov 08, 2014 | Office Equipment & Supplies

1 Answer

How do you set the Lanier LD035 duplex unit?


Metal tab on right side of copier is bent and correctly touching the duplex unit interlock switch. Open the duplexer and notice the metal tab stick out. Put back to a 90 degree angle.

Jul 30, 2014 | Lanier Office Equipment & Supplies

1 Answer

Default password for Lanier LD118d PCL


user is: admin
password is: password
for new model password is empty

Feb 06, 2013 | Lanier LD115 118 118D Toner 9 000 Yield

1 Answer

Copier Canon iR3300 error E000003-0000. How can I reset the copier if the monitor shows the error and it is not otherwise operable. I turned the main switch off and on to no avail. Can anybody help?...


Hi you need to enter in service mode first
in the control panel press the next secuence:
press adittional function
press 2 and 8 at the same time
press again adittional function
service mode should appear in the screen. if don't repeat the procedure until it does
in service mode press
COPIER, then FUNCTION, then CLEAR
select ERR and press ok
turn off the machine from the main switch for about a minute.
restart the machine and try to make some copies, if problem persist there is a malfunction in the fixing unit. get technical support. i hope this can help you

Oct 26, 2012 | Canon imageRUNNER 3300 All-In-One Laser...

1 Answer

I have a ricoh 2051 with this error message: Functional problem within the machine. Turn main power switch off and then on. if the error appears again, then call Here is the error message code: SC...


After turn the main switch off and on the error appears again????
This error means that there is a bad comunication between the controller board and the operation panel.
Did you intervew in the machine? Some tecnical intervewing?

Feb 17, 2011 | Ricoh Aficio 1035 Copier

1 Answer

LANIER 5637 FAULT CODE SC542 UPON POWER UP


You have a Fuser Temperature warm-up error, Hot roller warm-up error.
Verify the heater lamps, thermistor and thermofuse continuity.
Enter in the SP mode, turn OFF the main switch, unplug the machine, wait 10 seconds,
plug in and turn ON the copier.
If you need to reset the fuser,
Enter SP 5-810 (SC code reset) and
select "1". Then simultaneously press the Original Type key and the OK (or
R/#) key. (There is no need to turn the main switch off and on.).

Jan 22, 2011 | Lanier Office Equipment & Supplies

1 Answer

Hello there i have a lanier copier model ld 160c color copier everthing work fine and functional acceipt i can not make full color copy, when i press the full color button then the display panel show up TO...


Hi, somehow the external key counter option for your copier got turned on. This option is typically used for coin-operated copiers such as those found in libraries. You can turn this option off by doing the following:

- Press the User Tools button - Select System Settings - Select Admin Tools - Select Key Counter Management - Choose Off, or de-select the full-color option if it is selected. - Exit out of User Tools

Now you should be able to copy normally!

Dec 02, 2010 | Lanier UNKNOWN

1 Answer

Ar-160 display says "check panel" no more codes or functionality


tis problem is some of panel button is short i mean it is lock please open your machine panel board and service it . then solve your problem

Aug 02, 2009 | Sharp AR 201 Copier

1 Answer

Lanier 5645 copier - Code sc546


Try this press the "yellow/ca" botton, then enter 1-0-7, then press and hold the "red" stop" till the display changes. Once, it changes turn the Main power switch OFF. Not the one on the control pannel. Let it power down then turn it back ON. If the problem is still there try to turn the copier Off again and unplug the sorter/ finisher and turn the copier back ON. Is the problem gone, if so you may have to get a service person come in and repair the sorter. Good Luck.....

Apr 06, 2009 | Lanier Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lanier Office Equipment & Supplies Experts

quennie732

Level 2 Expert

422 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

gggg

Level 3 Expert

904 Answers

Are you a Lanier Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...