Who can replace a Admiral stove glass top?

The process for reinstalling a glass stove lid over burners may vary depending on the specific model and brand of stove. However, here are some general steps you can follow:

1. Clean the area where the glass stove lid will be installed. Make sure there is no dirt or debris that could cause the lid to sit unevenly.
2. Place the glass stove lid over the burners, making sure it is properly aligned with the stove top.
3. Check the tension of the springs that hold the lid open. If the springs are loose or not working properly, you may need to replace them.
4. Adjust the tension of the springs by turning the adjustment screws located on the hinges. You may need to use a screwdriver to turn the screws.
5. Test the tension of the springs by lifting and lowering the glass lid. It should move smoothly and stay open when lifted.
6. Once the tension is properly adjusted, tighten the screws on the hinges to secure the lid in place.
7. Test the lid again to ensure it is properly installed and the tension is correct.

If you are unsure about any part of the installation process or have difficulty adjusting the tension of the springs, it is recommended to consult the manual or contact the manufacturer for assistance.

1. Open oven door and remove two screws that secure top.
2. Lift up front and slide forward about 8 inches so that you can disconnect two wire couplings.
3. Place on table upside down(I put newspaper down to catch the broken shards of glass) and remove burner unit (1piece, 4 screws).
4. Place old burners on new stovetop in the same position as original.
5. Remove 4 white plastic shims (round) from old stovetop and put on new stovetop.
6. Tighten all screws and then sit it back on stove (two front tabs fit into slots) and then insert screws into holes and tighten.
7. Took about 20 minutes, including vacuuming broken glass from inside burners and cleaning grease form crevices between burners and old stovetop.
8. Wrap old stovetop in the newspapers that are underneath it and place it all in a plastic garbage bag to avoid any broken glass from falling out.

all is off, power supply is good, pop the top lil lid (normaly very top) and look for fuses

Please do not use the stove if the element is viable because of broken glass, this could become a danger to yourself.

Look at the cost of a new stove, you should be able to get one for
around 400.00. One of my customers had a glass top with 4 burners,
they had the same thing happen, the cost to replace the top was
1,200.00. So I would assume that you can get a new stove with 4
burners less then it would cost to replace the part on a stove you don't like. Maybe there is a LOWES around you to look at stoves,
they seem to be everywhere,like death and taxes.

As for putting a 4 burner top on a stove that has 2 with grill, I don't think it can be done without the extra cost of adding the parts to run the other 2 burners, so like I said in the long run,it just might be cheaper to but a new stove. It should not be a big deal to remove the exhaust from the grill part of the stove.

I looked at the model# you put down,and it does not have a grill,
from what I see, there are 4 burners and a downdraft vent in between the 4 burners, there are 6 models with this part # and none have a grill,only the downdraft vent.

If the model# is right, the cost would be around 300.00 for the glass, and then the cost of having it replaced. So I would say over
400.00, In which case for the same amount you could have a new one, but you must weigh the difference for yourself and see what you think is the best way to go.
If you have any more questions,please post back and everyone is more than willing to help you. I hope I have helped a little.

,.

These are plastic and will need to be replaced with new.
Once you have sourced new hinges then the machine top needs to be opened,
Electrically Isolate the machine, then at the joint between the machine front panel and top insert a flat blade 4" from each side to release the lid catches, tilt back the top to access the screws on the hinges and replace with new.

You can buy just the glass for your glasstop stove. I too need to replace my glass...I have a whilpool electric glasstop. Its not cheap...may just buy new stove. I priced just the glass for my whilpool at the cheapest I can find for $320.00. Thats a lot. Mind you its not the elements under the glass..its just the glass! So...idk bout you, but a whole new stove might be my best option. If you want to price the glass for your model just keyword search your number and brand of stove and type replacement glass. GOODLUCK! :)

im sorry about that.i have replace many of those running around 400$,that a lot of money.i have see glass top stoves on sale 4 that much.and i think they all are about the same as quilty goes.God bless,tom

yes, you can replace it with a glass that is the same thickness, do not have to be temper glass for the out side. so any glass company can make you a glass.

whats the entire model number?? and you cracked the main top glass assy??? ill look up tha part for you, not a teribly hard job, but depending on glass may be expensive

Check your warranty in the back of your use and care book. If the unit was manufactured prior to 1/1/06 it may have a five year part (not labor) warranty as long as you did not physically abuse it. The glass top comes as an assembled top (glass, the black seal, and the metal frame holding it)
Disconnect power. remove screws under the front edge of cook top. lift cook top and remove crossbars holding burners up against glass top. Unhook cook top / frame assemble. Install new top in reverse order.