I cant get to the webinterface

• Solid Blue - Normal operation, "Touch" mode is activated.
• Flashing Blue - Normal operation, the hands-free mode is activated.
• Solid Red - Warning mode - Replace batteries as soon as possible. While the water is running Solid Red LED is illuminated. When the water is off, the Red LED flashes once every 5 seconds. The faucet operates normally, solenoid valve is open.
• Rapid Flash Red - Alert Mode - Battery Failure Imminent. The Red LED flashes once a second. The first time the faucet is used, the Red LED will turn ON, the solenoid valve will be opened and remain open. The manual valve must be used until the batteries are replaced.
• Solid Red - Lockdown Mode - Replace Batteries. Extremely Low Batteries - The RED LED is ON, and water will not flow. The solenoid valve is closed and faucet will not operate until batteries are replaced.
• Long Flash Red (2 seconds on / 2 seconds off) - Board error, replace electronics kit, RP53230 See manual bypass of electronics section of Installation instructions.

Select "Accessibility" and turn the ON switch next to "LED Flash for Alerts"

1. Turn on the device that you want to set.
2. Aim the remote control at the device and press down and hold CODE SEARCH button for at least 3 seconds until the red LED lights up solid red.
3. Press the device button for the item you wish to program, e.g. TV, DVD, VCR, etc. and the LED light will blink once and then remain solid red.
4. Using the number keys, enter the 3-digit code. After you have entered the 3rd digit, the red LED will turn off indicating that the code was recognized for the device.
(NOTE: If the code entered was not compatible, the red LED will flash several times. You will then need to repeat Step 2. You have 30 seconds to enter a code.)
5. After the red LED light has turned off. Press the ON/OFF key. If the device you are trying to program powers off, then you have found the correct code. If the device does not power off, then you will need to repeat the process again from Step 2, using another 3-digit code.
The manual can be found at jumboremotecontrol.com

http://www.jumboremotecontrol.com/innovage_jumbo_remote_manual.PDF

Hi hislop_amand,

I know this is coming to you late yet I just seen your post and hope the following can still help you or others.

Kind Regards,
SD

FIRST ALERT Model: 9120 9120B

Normal Operation (AC Power)
Green LED ON; flashing Red LED once/ minute
No Audible Alarm

Normal Operation (DC Power - 9120B only)
Green LED OFF; Red LED flashes once/minute
No Audible Alarm

Hello
Code for Admiral TV with Innovage remote control are:
001,173

CODE INPUT SETTING:

You will need the list of codes to manually select and input the correct codes to your

specific device.

1. Turn on the device that you want to set.

2. Look for the brand name under the specific device listing provided.

3. Aim the remote control at the device and press down and hold CODE SEARCH button for

at least 3 seconds until the red LED lights up solid red.

4. Press the device button for the item you wish to program, e.g. TV, DVD, VCR, etc. and the

LED light will blink once and then remain solid red.

5. Using the number keys, enter the 1 st set of 3-digit codes from the list. You will notice

that each number that you press, the LED will blink once. After you have entered the

3rd digit, the red LED will turn off indicating that the code was recognized for the device.

(NOTE: If the code entered was not compatible, the red LED will flash several times.

You will then need to repeat Step 3. You have 30 seconds to enter a code.)

6. After the red LED light has turned off. Press the ON/OFF key. If the device you are trying

to program powers off, then you have found the correct code. If the device does not

power off, then you will need to repeat the process again from Step 3, using another

3-digit code.
7. Make a note of the 3-digit code for future use.

CODE SEARCH SETTING:

This is an alternative method to programming your device without using the code list. The

remote control will scroll through the list of codes to identify the correct code for your

device.

1. Turn on the device that you want to set.

2. Aim the remote control at the device and press and hold down the CODE SEARCH button

for at least 3 seconds until the red LED lights up solid red.

3. Press the device button for the item you wish to program, e.g. TV, DVD, VCR, etc. and the

LED light will blink once and then remain solid red.

4. Press ON/OFF button on remote slowly and repeatedly until the device you are trying to

program shuts off. (Note LED will blink once each time you press ON/OFF button)
5. Once this occurs, press ENTER button to store the code and the LED light will turn off

Did you get an answer for your alert information?

Have you installed the right driver for this cam? Open you device manager and check whether there is any red/yellow alert in it .Feel free to visit DigitalSupportTech for getting help.

go to profiles. and click advanced options and change it there it will have an option for everytime your phone should ring.. turn the Led light off as a reminder

you may want to reset the router first. the links below will show you how to manually install the device on your network

Setting up your Linksys router for Cable ISP


Setting up your Linksys router for DSL ISP


Setting up your Linksys router to have wireless security.

LED Display gives you your display visual alerts, signal strength, and operation mode. Here is an attached link for the manual.....http://www.uniden.com/pdf/LRD6399SWSom.pdf
But to answer your question here is what the difference between the green light and the red light are:
1. X-Band Signal Indicator—A green LED lights and blinks to
indicate the presence of an X-band radar signal. The blink rate
increases as the radar source gets closer. A distinct audio alert is
also heard.
2. K-Band Indicator— An amber (orange) LED lights and blinks to
indicate the presence of a K-band radar. The blink rate increases as
the radar source gets closer. A distinct audio alert is also heard.
3. Ka-SuperWideband Signal Indicator— A yellow LED lights and
blinks to indicate the presence of a Ka-SuperWideband radar
signal. The blink rate increases as the radar source gets closer. A
distinct audio alert is also heard.
4. Laser Signal Indicator— A red LED under L lights and blinks to
indicate the presence of a laser signal. A distinct audio alert is also
heard.
5. SWS Signal Indicator— When an early warning hazard or
informational signal is detected, the yellow SWS LED begins to
blink and the amber K-band LED lights. A distinct audio alert is
also heard.
6. Power-On Indicator— A green LED under P lights to indicate
power is being supplied to the unit and the unit is turned on.
7. LED Signal Strength Meter—Four LEDs give an accurate visual
indication of the strength of radar or laser signals.
8. City Mode Indicator—A green LED under C lights to indicate
that you selected City Mode.
9. Auto Mute Indicator— A red LED under M lights to indicate that
you selected the Auto Mute feature.

Please make sure you give me a rating and I hope this helps,
cbinny1