Why can't I get SOURCE button to select DVD? - Apex Digital GT2715DV 27 in. TV/DVD Combo

Without a remote controller, you may have limited options to change modes on your Apex digital TV. However, you may be able to change the mode by using the buttons on the TV itself.
Here are some general steps you can try:

1. Turn on your TV and make sure your DVD player is connected to it.
2. Look for the "Menu" button on the TV and press it.
3. Navigate through the menu options using the arrow buttons on the TV until you find "Input" or "Source."
4. Press the "Enter" button to select the input/source option.
5. Use the arrow buttons to select the input/source that corresponds to your DVD player.
6. Press the "Enter" button to confirm the selection.
7. Press the "Menu" button to exit the menu.

Note that the specific steps may vary depending on the model of your Apex TV. You may also consult the user manual for your TV for more information on changing modes without a remote controller.

Some Insignia tvs have a button on the bottom to select the input mode. Otherwise try finding a replacement remote or universal remote that will work.

You need to select the input source to TV. Press the input or source button on the TV or your remote.

If you have the remote for the television you can select the input channels by locating the "Source" or "Input" button. You'll then be able to select HDMI, VGA, TV, etc.

If you're lacking the remote the television itself should also have an Input/Source button in which you can then use to select HDMI.

Note: If using the television buttons pressing the Input/Source should cycle through the available selections, if not you may need to press this button ONCE and then cycle through your choices using Volume or Channel buttons. Once highlighted for a few seconds it should automatically select the desired channel - if not you will need to press your Input/Source button again to confirm your selection.

You probably have on your car stereo either a single push button that you press to select the audio source (Radio/CD/DVD/Bluetooth) or 4 separate buttons labeled: Radio, DVD, CD, Bluetooth, respectively. Because a sync operation can refer only to a Bluetooth audio source (phone, tablet), your stereo is in now in the source mode for a Bluetooth audio source. Find the button or buttons for the selecting the audio source and select Radio or CD or DVD (you are already on Bluetooth).

Hi tappetanders,

There are usually two AV modes in the TV which allow you to select the source , therefore , you need to select the correct one, usually there is a button names as AV or similar which allows you to select the video input source, once you select this source properly then you should be able to see the video.

Hope this helps ...:) Let me know in case you have any further queries.

Please select Source Button from your LCD remote to change source and select any other source or select DVD mode.

Hi, usually the function button on the remote control to select the input mode / source is a circle or a square with an arrow pointing into it (see below).


Each time you press this, the next available source is selected in a set order, e.g. TV / AV1 / AV2 / HDMI / PC

If using a SCART interface for your DVD player, the TV should automatically switch to the DVD source when you activate the DVD player (take it out of standby).

Some dvd players do not have the switching line fro your tv to automatically select scart input but you will be able to select via the tv remote if there are no buttons marked av it can be an oblong with an arrow pointing inwards or you may have to select via the source menu on the tv if you have your original handbook it will give a helpline number for Asda.SUPER8.

Hi,

Three (3) things you can try:
1. Lower down the Screen resolution of your laptop as well as the Color quality and the Screen refresh rate before doing the Fn + F5. If it works, adjust thereafter;
2. Do a soft (Factory) reset of your Cinego in the in the Management Menu (credit to Cooljazz); and/or
3. it is just "slow" in sensing the presence of a VGA source as it cycles in its selection, internal DVD, VGA, Composite Video IN. Since it does not have a manual source selection, your only option is to really wait or ...Verify that "Auto Source Select" is enabled in the Management Menu (buttons-Proj/Setup then >/9) and "tap" the "SRC" button on the projector itself to manually initiate the input/source selection.

Hope this be of some help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.