Where can I buy parts to rebuild the steam release like orings

Bostitch nailers are simple to rebuild. Bostitch company was sold to Dewalt so parts are now easier to obtain from local Dewalt service center. Use Ork11 oring kit and tva6 trigger valve. These parts are also available on ebay. Good luck or your nailing projects.

Usually, rebuild kit has a replacement trigger valve. However if you are attempting to rebuild the valve, pay close attention to the fit of the orings where they make contact. The valve has four parts. End cap, lower body, inner spool and trigger pin. The critical orings are on the pin and spool. Replace all the orings, making sure that parts fit snuggly. The trigger pin orings should fit snug against end cap and inner spool. The inner spool should fit snuggly into end cap and lower half of the valve. Good luck with your repair.

did you lube all the orings before putting tool back together, also make sure the right oring is in the right place , many orings look similar but are not

Dewalt uses vinyl orings in the trigger valve (clear to gold color oring on the firing pin) and are known to fail. You can pop out the valve and replace with new ( part # 603396.00) or try replacing the orings. It is hard to find small orings (i think it uses 2mm x 1.5mm). Also there are two to four orings made of vinyl within the gun. Two between the cylinder and cylinder retainer and two in the head. Rebuild kit may still be available. Good luck

Yes, the manufacturer should have a parts kit for replacing the orings and seals..it's probably leaking right where the motor meets the impeller...there should be a seal inside there...the rebuild kit should have a blow-up diagram to assist you in changing parts

Stanley Bostitch doesn't make kits to rebuild their nail guns, you have to order each o-ring, seal, etc. seperately. The N16 was a good gun however there are very few parts available for them. You can go to www.bostitch.com to see what's available through them. You can also get part numbers for what you need for your guns and research any available parts on the web.

Assuming no air leaks when you connect air to gun. Remove nails and remove roll pin holding trigger allowing access to pin of trigger valve. With very quick motion depress trigger pin all the way in. If the gun fires then most likely problem with safety and trigger not being pushed all the way up against valve pin. If the gun does not fire, most likely problem with headvalve orings not seating due to scratches where orings contact metal. Remove head and examing metal parts and sand with fine paper to remove scratches (400 grit to finish). Install headvalve into head with plenty of silicone paste lube and push headvalve down into head with thumbs. Cover venthole on sealing surface of head with finger and release thumb pressure. The headvalve should stay down in head with vacuum and release when you release finger on vent hole. If no vacuum then orings are not sealing and gun will not work correctly. Good holidays

The rebuild kit # ( ork11) is available on ebay or here:
http://www.mendingshed.com/ork11.html

This kit may not have all the orings but does include other parts needed. There are other kits available on ebay that would include all the orings but missing other parts.
Sometimes all you need is to open gun and clean orings and contact surfaces and lube with silicone paste (sold at Lowes in the plumbing department used to lube faucet orings). The cylinder seal on top of the cylinder and orings at cylinder spacer is usually cause of leak at nose of gun. Good luck

If second gear stuck it need rebuilt ore replaced.
check what labor to rip one out replace a junk yard one ore check see what cost rebuilt it.
stay away form amco there rip off artist.
Your cost about 900 to 1000/.
if you do your self 600 for junk yard one and few hundread if you can get rebuild kit rebuild the trasmission your self.
I took trans rebuilt i rather buy used ore pay some rebuild it.
Give thumbs up if that help seya

I have been buying Bostitch t31 parts on ebay. Rebuild kit usually about $22 - 39 depending on how luckey you are at bidding. Keep searching on Ebay for other parts for this gun as parts are not available at Bostitch.com any longer. The oring kit for the N60 is available at amazon.com. the part number is ORK1, cost under $20. You can also find bargains on ebay. When installing orings us silicone grease. It is available at lowes in the plumbing department. It looks like vaseling. It is used for lubricating orings in faucets. Good luck on your repair project.