How can I get it to print?

Blocked print head nozzles
Inkjet printers need to be used frequently to prevent blocked print head nozzles. You may have blocked print head nozzles.
Try the printer maintenance to clear the printer nozzles.
After several deep cleaning attempts and there is no improvements in the print then a new print head is required.
A new print head maybe expensive and it maybe more cost effective to purchase a new printer.

f print quality does not improve by the standard cleaning of the Print Head, clean the Print Head deeply. Cleaning the Print Head deeply consumes more ink than the standard cleaning of the Print Head, so clean the Print Head deeply only when necessary.
1. Make sure that the power is turned on.

2. Clean the Print Head deeply. (1) Press the (Maintenance) button repeatedly until y appears.
(2) Press the Black or Color button.
The machine starts cleaning the Print Head deeply. Do not perform any other operations until the machine completes the deep cleaning of the Print Head. This takes about 2 minutes.

3. Check the print head condition.

When the deep cleaning is completed, the LED returns to the copy standby mode. To check the print head condition, print the nozzle check pattern.

See " Printing the Nozzle Check Pattern".

If the problem is not resolved, turn off the power and clean the Print Head deeply again after 24 hours.
If the problem is still not resolved, replace the FINE Cartridge with a new one.

See " Replacing FINE Cartridges".
If the problem is still not resolved after replacing the FINE Cartridge, contact the service center.

Printing the Nozzle Check Pattern
Print the nozzle check pattern to determine whether the ink ejects properly from the print head nozzles.

NOTE If the remaining ink level is low, the nozzle check pattern will not be printed correctly. Replace the FINE Cartridge whose ink is low.
See " Replacing FINE Cartridges".



You need to prepare: a sheet of A4 or Letter-sized plain paper

1. Make sure that the power is turned on.

2. Load a sheet of A4 or Letter-sized plain paper in the Rear Tray.

3. Open the Paper Output Tray gently, and open the Output Tray Extension.

4. Print the nozzle check pattern.

(1) Press the (Maintenance) button repeatedly until A appears.
(2) Press the Black or Color button.

The nozzle check pattern will be printed.

5. Examine the nozzle check pattern.
See Examining the Nozzle Check Pattern.

Examining the Nozzle Check Pattern

Examine the nozzle check pattern, and clean the Print Head if necessary.

1. Check if there are missing lines in the pattern (1) or horizontal white streaks in the pattern (2). (1) Check if lines are missing in this pattern. If yes, the cleaning is required.
See " Cleaning the Print Head".


(A) Good
(B) Bad (lines are missing)

(2) Check if horizontal white streaks are present in this pattern. If yes, the cleaning is required.
See " Cleaning the Print Head".

(A) Good
(B) Bad (horizontal white streaks are present)
Post back!

Performing Maintenance:




Note :
Be sure to install the ink tanks in the correct order indicated by the label on the Print Head Holder. The machine will not print if an ink tank is installed in the incorrect position.
Step 1
Printing the Nozzle Check Pattern.




If lines are missing or if white streaks appear


Step 2
Print Head Cleaning.

If the problem is not resolved after performing Print Head Cleaning twice


After cleaning the Print Head, print and examine the nozzle check pattern (Step 1) again.


Step 3
Print Head Deep Cleaning.



If Print Head Deep Cleaning does not resolve the problem, turn off the machine and perform another Print Head Deep Cleaning after 24 hours. If the problem is still not resolved and if you are sure that the ink didn't run out, then the Print Head may be damaged. Contact your Canon service representative.

Hope this helps.
All the best.

Hi there,
When printing becomes faint or colors are incorrect, even if ink remains in the ink tanks, the print head nozzles are probably clogged. Follow the procedures below to clean the nozzles.

Step 1 : Printing the Nozzle Check Pattern.
If white stripes are noticeable
Step 2 : "Aligning the Print Head"
If print quality is poor
Step 2 : "Print Head Cleaning"
if the problem remains
Step 3 : Print Head Deep Cleaning"
if the problem still remains
Step 4 : Replacing Ink Tanks.

Note : * If the ink tank replacement does not resolve the problem, contact the Customer Care Center.
* You will be alerted if low ink warning is enabled.
* When the Maintenace button on the operation panel is pressed, the maintenance mode is shown. Numbers and functions that can be selected on the maintenance mode as follows :
01 : Printing the Nozzle Check Pattern
02 : Print Head Cleaning
03 : Print Head Deep Cleaning
04 : Aligning the Print Head
05 : Reset the ink counter.
06 : "Display" or "Not Display" remaining ink volume.
07 : Date and order setting.

Printing the Nozzle Check Pattern : Print the nozzle check patterb to determine whether the ink ejects properly from the print head nozzles and to verify print head alignment. Use this function when printed results are blurred or the color is incorrect,
1) With the printer on, load a sheet of Letter paper in the printer.
2) Print the Nozzle Check Pattern.
a) Press the Maintenance button,
b) The Maintenance icon and 01 appear on the LCD.
c) Press the OK button. The nozzle check pattern is printed.
3) Examine the nozzle check pattern output by the printer.
a) Lines missing in this pattern indicate that the print head of black ink requires cleaning. Perform the Print Head Cleaning.
b) White stripes in this pattern indicate that the print head of color ink requires cleaning. Perform the Print Head Cleaning.
c) Uneven patterns indicate that the print head requires alignment.
Perform Aligning of Print Head.
d) Noticeable white stripes in this pattern indicate that the print head require alignment.
Perform Aligning of Print Head.

Print Head Cleaning : Clean the print head if you suspect that the nozles might be clogged. Cleaning the print head consumes ink, so perform print head cleaning only when necessary.
1) Ensure that the printer is on.
2) Start print head cleaning.
a) Press Maintenance button.
b) Press right arrow once to display 02 on the LCD.
c) Press the OK button.
Important : Do not perform any other operations until the print head cleaning finishes. This takes about 50 seconds.
Note : After the print head cleaning finishes, print the nozzle check pattern to verify that the print head nozzles are clean.
If the problem persists, perform printhead deep cleaning.

Print Head Deep Cleaning : If print quality does not improve by standard print head cleaning, try print head deep cleaning, which is more powerful process. Print head deep cleaning consumes ink, so perforn this procedure only when necessary.
1) Ensure that the printer is on.
2) Start Print Head Deep cleaning.
a) Press Maintenance button.
b) Press right arrow twice to display 03 on the LCD.
c) Press the OK button.
Important : This process takes one or two minutes to complete so simply wait until the Power lamp stops flashing.
Note : After printhead deep cleaning finishes, print the nozzle check pattern to verify that the printhead nozzles are clean.
If the printhead is still not clean after the second deep cleaning, replace the ink tank.
If ink tank replacement does not resolve the problem, the print head may be worn out. Contact the Customer Care Center.

Hope this helps.
Please rate my response.
Thanks.

Have a good day.

Hi there,

When Printing Becomes Faint or Colors are Incorrect.
When printing becomes faint or colors are incorrect even if the ink remains in the ink tanks, the print head nozzles are probably clogged. Print the nozzle check pattern to confirm the condition of the nozzles and then perform the Print Head Cleaning.
Note : Before performing maintenace

*Open the Scanning Unit (Printer Cover) and make sure that all lamps for the ink tanks are lit red.
-If any one of the lamps is flashing slowly, the associated ink tank is running low. You can continue printing for a while, but we recommend you to have replacement ink tank available.
-If any one of the lamps is flashing fast, the associated ink tank is emty. Replace the ink tank.
If an ink tank is flashing fast even though ink remains in that ink tank, it is inserted into the wrong position. Make sure that the ink tank of the correct coloris inserted in each position matching the label.
-If the ink lamp is not lit, the tank is not set properly. Press the <PUSH> mark on the ink tank until the tank clicks into place. Make sure that all the packaging material is peeled off the ink tank.

*Increase the print quality setting in the printer settings.

Step 1 : Printing the Nozzle Check Printer.
1) Make sure that the machine is turned on, open the Front Feed and extend the Output Paper support.
2)Load a sheet of A4 or Letter-sized plain paper in the Auto Sheet Feeder or the Front Feeder.
Set the Paper Thickness Lever to the left.
3) Press the Paper Feed Switch to select the paper source where you have loaded paper.
4)Print the nozzle check pattern.
a) Press the Menu button.
b) Use the right and left arrow buttons to select the Maintenance/settings, then press the OK button.
The maintenance /setting screen is displayed.
3) Use the right and left arrow buttons to select Maintenance, then press the OK button.
The Maintenance screen is displayed.
4) Use the Up and Down arrow buttons to select the Nozzle check and then press the OK button.
The pattern confirmation screen is displayed.
5) Use the Up and Down arrow buttons to select Yes and the press the OK button.
The nozzle check print is printed, and the pattern confirmation screens are displayed alternately.

Examine the pattern and take the appropriate action.


Step 2: Print Head Cleaning
Clean the Print Head if lines are missing or if white streaks appear in the printed nozzle check pattern. Cleaning unclogs the nozzles and restores the print head condition. Note that cleaning the Print Head causes used inl to be absorbed in the ink absorber. Cleaning the Print Head consumes ink, so perform Print Head Cleaning only when necessary.
1) Make sure that the machine is on, open the Fron Feeder, and extend the Output Paper Support.
2) Load a sheet of A4 or Letter-sized plain paper in the Auto Sheet Feeder or the Front Feeder/
Set the Paper Thickness Lever to the left.
3) Press the Paper Feed Switch to select the paper source where you have loaded paper.
4) Start Print Head Cleaning.
a) Press the Menu button.
b) Use the right and left arrow button to select Maintenance/settings, then press the OK button.
The maintenance /setting screen is displayed.
c) Use the right and left arrow buttons to select Maintenance, then press the OK button.
The Maintenance screen is displayed.
d) Use the Up and Down arrow buttons to select Cleaning and then press the OK button.
The confirmation screen is displayed.
e) Use the Up and Down arrow buttons to select Yes and the press the OK button.
Print Head Cleaning starts.
Do not perform any other operations until Print Head cleaning finishes. This takes about 50 seconds.
The pattern print confirmation screen is displayed.
f) Use the Up and Down arrow buttons to select Yes and the press the OK button.
The nozzle check print is printed, and the pattern confirmation screens are displayed alternately.
Examine the pattern and take the appropriate action.
Note : If the problem is not resolved after performing steps 4 and 5 twice, try Print Head Deep Cleaning.

Print Head Deep Cleaning.
If print quality does not improve by standard Print head Cleaning, try the Print Head Deep Cleaning, which is more powerful process. Note that cleaning the Print Head causes used ink to be absorbed in the ink absorber. Print Head deep Cleaning consumer more ink than the standard Print Head Cleaning, so perform this procedure only when neccessary.
1) Make sure that the machine is on, open the Fron Feeder, and extend the Output Paper Support.
2) Load a sheet of A4 or Letter-sized plain paper in the Auto Sheet Feeder or the Front Feeder/
Set the Paper Thickness Lever to the left.
3) Press the Paper Feed Switch to select the paper source where you have loaded paper.
4) Start Print Head Cleaning.
a) Press the Menu button.
b) Use the right and left arrow button to select Maintenance/settings, then press the OK button.
The maintenance /setting screen is displayed.
c) Use the right and left arrow buttons to select Maintenance, then press the OK button.
The Maintenance screen is displayed.
d) Use the Up and Down arrow buttons to select Deep Cleaning and then press the OK button.
The confirmation screen is displayed.
e) Use the Up and Down arrow buttons to select Yes and the press the OK button.
Print Head Deep Cleaning starts.
Do not perform any other operations until Print Head Deep cleaning finishes. This takes about 100 seconds.

5) Check the condition of the Print Head.
a) Print the nozzle check pattern to check the print head condition.
If a particular color is not printed properly, replace the ink tank of that color.
b) If the print head nozzles are still not cleaned, turn off the machine and perform another Print Head Deep Cleaning after 24 hours.
c) If this does not solve the problem, the Print Head may be damaged. Contact your Canon service representative.

Hope this helps.
Please rate my response.
Thanks.
Have a good day.

Hi there,

To avoid drying of the Print Head and clogging of the nozzles, note the following.
*When you turn off the Machine
Follow the procedure below to turn off the machine.
1)Press the ON/OFF button to turn off the machine,
2) Confirm that the POWER lamp has gone out.
This takes a few seconds or as long as 20 seconds.
3) Unplug the power cord from the wall outlet.
If you are using a power outlet strip, you can switch off instead.
When you press the ON/OFF button to turn off the machine, the machine automatically puts a protective cap on the Print Head to prevent the ink from drying. If you remove the power cord or switch off the power outlet strip before the POWER lamp goes out, this capping will not be done properly, causing the Print Head to dry and clog.

* When You are not Using the Machine for a Long Time.
When you are not using the machine for a long time, print or copy in both black and white and in color or pertorm Print Head Cleaning, about once a month to prevent degradation of the Print Head.
Numerous nozzles are installed in the Print Head for high -precision printing. Just as the uncapped tip of a ballpoint pen or marker becomes dry and unusable if it is not used for a long period of time, the print nozzles becomes blocked by dried ink. Periodically printing or cleaning of the Print Head can prevent this blockage.
Note :
*If the printed area is traced with a highlight pen or paint-stick or stained with water or sweat, ink may blur depending in the paper.
*If the print head nozzles get clogged , printouts will become faint or particular colors will not be printed properly.

When Printing Becomes Faint or Colors are Incorrect.
When printing becomes faint or colors are incorrect even if the ink remains in the ink tanks, the print head nozzles are probably clogged. Print the nozzle check pattern to confirm the condition of the nozzles and then perform the Print Head Cleaning.
Note : Before performing maintenace

*Open the Scanning Unit (Printer Cover) and make sure that all lamps for the ink tanks are lit red.
-If any one of the lamps is flashing slowly, the associated ink tank is running low. You can continue printing for a while, but we recommend you to have replacement ink tank available.
-If any one of the lamps is flashing fast, the associated ink tank is emty. Replace the ink tank.
If an ink tank is flashing fast even though ink remains in that ink tank, it is inserted into the wrong position. Make sure that the ink tank of the correct coloris inserted in each position matching the label.
-If the ink lamp is not lit, the tank is not set properly. Press the <PUSH> mark on the ink tank until the tank clicks into place. Make sure that all the packaging material is peeled off the ink tank.

*Increase the print quality setting in the printer settings.

Step 1 : Printing the Nozzle Check Printer.
1) Make sure that the machine is turned on, open the Front Feed and extend the Output Paper support.
2)Load a sheet of A4 or Letter-sized plain paper in the Auto Sheet Feeder or the Front Feeder.
Set the Paper Thickness Lever to the left.
3) Press the Paper Feed Switch to select the paper source where you have loaded paper.
4)Print the nozzle check pattern.
a) Press the Menu button.
b) Use the right and left arrow buttons to select the Maintenance/settings, then press the OK button.
The maintenance /setting screen is displayed.
3) Use the right and left arrow buttons to select Maintenance, then press the OK button.
The Maintenance screen is displayed.
4) Use the Up and Down arrow buttons to select the Nozzle check and then press the OK button.
The pattern confirmation screen is displayed.
5) Use the Up and Down arrow buttons to select Yes and the press the OK button.
The nozzle check print is printed, and the pattern confirmation screens are displayed alternately.

Examine the pattern and take the appropriate action.


Step 2: Print Head Cleaning
Clean the Print Head if lines are missing or if white streaks appear in the printed nozzle check pattern. Cleaning unclogs the nozzles and restores the print head condition. Note that cleaning the Print Head causes used inl to be absorbed in the ink absorber. Cleaning the Print Head consumes ink, so perform Print Head Cleaning only when necessary.
1) Make sure that the machine is on, open the Fron Feeder, and extend the Output Paper Support.
2) Load a sheet of A4 or Letter-sized plain paper in the Auto Sheet Feeder or the Front Feeder/
Set the Paper Thickness Lever to the left.
3) Press the Paper Feed Switch to select the paper source where you have loaded paper.
4) Start Print Head Cleaning.
a) Press the Menu button.
b) Use the right and left arrow button to select Maintenance/settings, then press the OK button.
The maintenance /setting screen is displayed.
c) Use the right and left arrow buttons to select Maintenance, then press the OK button.
The Maintenance screen is displayed.
d) Use the Up and Down arrow buttons to select Cleaning and then press the OK button.
The confirmation screen is displayed.
e) Use the Up and Down arrow buttons to select Yes and the press the OK button.
Print Head Cleaning starts.
Do not perform any other operations until Print Head cleaning finishes. This takes about 50 seconds.
The pattern print confirmation screen is displayed.
f) Use the Up and Down arrow buttons to select Yes and the press the OK button.
The nozzle check print is printed, and the pattern confirmation screens are displayed alternately.
Examine the pattern and take the appropriate action.
Note : If the problem is not resolved after performing steps 4 and 5 twice, try Print Head Deep Cleaning.

Print Head Deep Cleaning.
If print quality does not improve by standard Print head Cleaning, try the Print Head Deep Cleaning, which is more powerful process. Note that cleaning the Print Head causes used ink to be absorbed in the ink absorber. Print Head deep Cleaning consumer more ink than the standard Print Head Cleaning, so perform this procedure only when neccessary.
1)
1) Make sure that the machine is on, open the Fron Feeder, and extend the Output Paper Support.
2) Load a sheet of A4 or Letter-sized plain paper in the Auto Sheet Feeder or the Front Feeder/
Set the Paper Thickness Lever to the left.
3) Press the Paper Feed Switch to select the paper source where you have loaded paper.
4) Start Print Head Cleaning.
a) Press the Menu button.
b) Use the right and left arrow button to select Maintenance/settings, then press the OK button.
The maintenance /setting screen is displayed.
c) Use the right and left arrow buttons to select Maintenance, then press the OK button.
The Maintenance screen is displayed.
d) Use the Up and Down arrow buttons to select Deep Cleaning and then press the OK button.
The confirmation screen is displayed.
e) Use the Up and Down arrow buttons to select Yes and the press the OK button.
Print Head Deep Cleaning starts.
Do not perform any other operations until Print Head Deep cleaning finishes. This takes about 100 seconds.

5) Check the condition of the Print Head.
a) Print the nozzle check pattern to check the print head condition.
If a particular color is not printed properly, replace the ink tank of that color.
b) If the print head nozzles are still not cleaned, turn off the machine and perform another Print Head Deep Cleaning after 24 hours.
c) If this does not solve the problem, the Print Head may be damaged. Contact your Canon service representative.

Hope this helps.
Please rate my response.
Thanks.
Have a good day.

You need to conduct the following steps:
Printing the Nozzle Check Pattern
The nozzle check pattern shows if each print head nozzle is operating properly.

You can also print the nozzle check pattern from your computer.

1. Load A4- or letter-size plain paper in the Auto Sheet Feeder (ASF) or cassette.
2. Press <Feed Switch> button to select the paper source.
3. In either COPY, PHOTO, or FILM menu screen, press <Menu> button.
4. Press the left or right arrow to select [Maintenance/Settings], then press <OK>.
5. Use left or right arrow to select [Maintenance] and press <OK>.
6. Use up or down arrow to select [Nozzle Check] and press <OK>.
7. When prompted to print a nozzle check pattern, use the up arrow to select [Yes] and then press <OK>.
   The machine prints a nozzle check pattern

Print Head Cleaning / Head Refreshing
If the printed nozzle check pattern is broken, missing, or a specific color is not printed, clean the print head.
MEMO:
a. Cleaning the print head consumes a small amount of ink. Cleaning too often reduces the amount of ink in the ink tanks.
b. Print head cleaning is performed when you connect the power cord. Your machine may perform print head cleaning periodically to avoid clogging.

1. In either COPY, PHOTO, or FILM menu screen, press <Menu> button.
2. Press the left or right arrow to select [Maintenance/Settings], then press <OK>.
3. Use left or right arrow to select [Maintenance] and press <OK>.
4. Use up or down arrow to select [Print Head Cleaning] or [Head Deep Cleaning] as necessary and then press <OK>.

When prompted to clean the print head, use the up arrow to select [Yes and then press <OK>.

IMPORTANT:
If normal print head cleaning does not improve print quality, perform deep print head cleaning.
Print Head Alignment in Windows
If colors mix or streaks appear in the nozzle check pattern, perform the print head alignment.
The print head alignment can be performed either automatically or manually.
If the automatic print head alignment does not resolve the problem, perform the print head alignment manually.

Your feedback is very important to us, please do not forget to rate my service for the site to continue helping everyone and improve on it.
I thank you for the opportunity to help and please do not hesitate in contacting me for any further questions…god bless

Hi ...

I would suggest you try and clean the print head and that should resolve the problem. Follow the below steps to clean the print head:

Perform a Cleaning of the print head:
Caution: Cleaning consumes a certain amount of ink. Perform Cleaning only when necessary.
Note: The pattern varies depending on the printer and version of Windows being used.

1. Click 'Cleaning' to perform print head cleaning from the Pattern Check window and proceed to step 3 of the print head cleaning instructions. If the Pattern Check window is closed, skip this step and proceed to step 2.
   
   
   
   
   
2. To perform a print head cleaning from the Maintenance window, click 'Cleaning'.
   
   
   
   
3. When the Print Head Cleaning window is displayed, select the target ink group for 'Cleaning'.
   
   
   Note: When performing Cleaning for all colors, check 'All Colors'.
   
   
   
   
   Note: When performing Cleaning for Black only, deselect 'All Colors' and check 'Black'.
   
   
   
   
   Note: When performing Cleaning for Color only, deselect 'All Colors', and check 'Color'.
   
   
   
   
4. After selecting the target ink group click 'Execute' to perform the cleaning of the print head nozzles.
   
   
   
   
5. When the confirming message is displayed, check the contents, and click 'OK'.
   
   
   Caution: Although the Nozzle Check window is displayed, do not perform any other operations until Cleaning is completed.. Cleaning will take about 40 seconds.
   
   
   
6. Print a Nozzle Check Pattern and examine.
   
   
7. Perform Cleaning again if necessary.
   
   
   Memo: If the pattern is still abnormal after two Cleanings, perform up to two Deep Cleanings.
   
   
   

Perform Deep Cleaning of the print head
Caution: Deep Cleaning consumes a larger amount of ink than normal Cleaning. Perform Deep Cleanings only when necessary.

1. In the Maintenance window, click 'Deep Cleaning'.
   
   
   
   
   Note: The layout varies depending on the printer and version of Windows you are using.
   
   
2. When the Deep Cleaning window is displayed, select the target ink group for Deep Cleaning.
   
   
   
   
   Note: When performing Cleaning for all colors, check 'All Colors'.
   
   
   
   
   Note: When performing Cleaning for Black only, deselect 'All Colors' and check 'Black'.
   
   
   
   
   Note: When performing Cleaning for Color only, deselect 'All Colors', and check 'Color'.
   
   
   
   
3. Click 'Execute'.
   
   
   
   Memo: By clicking 'Initial Check Items' before clicking 'Print Check Pattern', you can see the specific confirmation items in Nozzle Check.
   
   
4. When the confirming message is displayed, click 'OK'. (The Power lamp will blink green and Deep Cleaning starts. The blink stops when Deep Cleaning is over.)
   
   
5. When Deep Cleaning starts, check the contents, and click 'OK'.
   
   
   Caution: To prevent interruption of the Deep Cleaning process, do not perform any other operations until Deep Cleaning is completed. When the operation of the printer is stopped, Deep Cleaning is completed. Deep Cleaning will take about 75 seconds.
   
   
   
6. Print Nozzle Check again.
   
   
   Note: If the printed pattern is still not normal, perform steps 1 through 4 of the Deep Cleaning process one additional time.
   
   
   Caution: If after two Deep Cleanings the Nozzle Check Pattern is still not normal, turn the printer off and let it sit for 24 hours or more before attempting another Deep Cleaning again. The wait time may allow dried ink in clogged print head nozzles to liquefy, and resolve the problem
   

If this does not resolve the problem, please reply back and we'll try the next step ...

Don't forget to vote if this helps ... Cheers :)

Cleaning your head might resolve your problem. Perform the below steps to clean the head:

Print Head Cleaning / Head Refreshing If the printed nozzle check pattern is broken, missing, or a specific color is not printed, clean the print head (Cleaning) or print head deep cleaning (Deep Cleaning). Note:

1. Cleaning the print head consumes a small amount of ink. Cleaning too often reduces the amount of ink in the ink tanks.
   
   
2. Print head cleaning is performed when you connect the power cord. Your machine may perform print head cleaning periodically to avoid clogging.
   

Overview:
Step1:
Print the Nozzle Check Pattern.
To check whether the print head nozzles are clogged, print the Nozzle Check Pattern.
If the print quality is poor, perform print head cleaning.
Step 2:
Perform print head cleaning.
This unclogs the print head nozzles
Print the Nozzle Check Pattern again.
To check whether the print head nozzles are clogged, print the Nozzle Check Pattern.
If the print quality is still poor, perform two print head cleanings.
Print the Nozzle Check Pattern again.
Step 3:
Perform deep print head cleaning.
This is a more powerful cleaning.

Displaying the Maintenance screen

1. Ensure that the printer is powered on.
   
   
2. Press the <Menu> button.
   
   
3. Press the left or right cursor to select [Maintenance/settings], then press <OK>.
   
   
4. Press the left or right cursor to select [Maintenance], then press <OK>.
   

Print Nozzle Check Pattern

1. Press the Open button to open the output tray.
   
   
   
   
2. Load letter-sized plain paper in the auto sheet feeder (ASF) or the cassette.
   
   
3. Display the Maintenance screen on the printer.
   
   
4. Press the up or down cursor to select [Nozzle check], then press the <OK>.
   
   
   
   
5. Press the up or down cursor to select [Yes], then press <OK>. (The nozzle check pattern is printed.)
   
   
6. Confirm the nozzle check pattern.
   

< 1 > The normal nozzle check pattern
< 2 > The abnormal nozzle check pattern
< 3 > Some black ink lines are broken.
< 4 > White lines are present in the color ink pattern.
< 5 > Both black and color inks are not present.

Note:

1. When all patterns are printed normally, press the up / down cursor button to select "All A" and press the OK button.
   
   
2. When any patterns are printed abnormally, press the up / down cursor button to select "Also B" and press the OK button.
   

Print Head Cleaning:

1. Display the Maintenance screen on the printer.
   
   
2. Press the up or down cursor to select [Cleaning], then press <OK>.
   
   
   
   
3. Press the up or down cursor to select [Yes], then press <OK> to start print head cleaning.
   
   Note:
   Do not do any other operations until print head cleaning is completed.
   
   
   
4. Print the nozzle check pattern and check the print head status.
   

Deep (Print Head) cleaning:

1. Display the Maintenance screen.
   
   
2. Press the up or down cursor to select [Deep cleaning], then press <OK>.
   
   
   
   
3. Press the up or down cursor to select [Yes], then press <OK> to start print head deep cleaning.
   
   Note:
   Do not do any other operations until print head deep cleaning is completed.
   
   
   
4. Print the nozzle check pattern and check the print head status.
   
   Note:
   If the printed result does not improve even after doing print head deep cleaning, turn off the printer. Then, after 24 hours or later, do print head deep cleaning again. (After a given time interval, ink could dissolve itself, resulting in ink unclogging.)
   

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Print Head Cleaning / Head Refreshing If the printed nozzle check pattern is broken, missing, or a specific color is not printed, clean the print head. NOTE:
a. Cleaning the print head consumes a small amount of ink. Cleaning too often reduces the amount of ink in the ink tanks.
b. Print head cleaning is performed when you connect the power cord. Your machine may perform print head cleaning periodically to avoid clogging.

1. Press <COPY> or <PHOTO>.
   
   
2. Press <Menu> repeatedly until <USER DATA> appears.
   
   
3. Press < (left arrow) or > (right arrow) to select [MAINTENANCE].
   
   
   
   
4. Press <OK>.
   
   
5. Use < or > to select [CLEANING] or [HEAD REFRESHIN] as necessary.
   
   
   
   [CLEANING]: Performs normal print head cleaning.
   [HEAD REFRESHIN]: Performs deep print head cleaning.
   
   
6. Press <OK>.
   
   
   
   
7. Print a Nozzle Check Pattern to see if print quality improved.
   
1. Press <COPY> or <PHOTO>.
   
2. Press <Menu> repeatedly until <USER DATA> appears.
   
3. Press < (left arrow) or > (right arrow) to select [MAINTENANCE].
   
   
   
4. Press <OK>.
   
   
   
5. Press <OK> again.
   The machine prints a nozzle check pattern (A).
   
   
   
   
8. If broken or white lines appear in the pattern, perform two Head Refreshings (from steps 1 through 6) then print another Nozzle Check Pattern.
   
   
9. If print quality does not improve after two Head Refreshings, replace the appropriate ink tank.

Confirming The Nozzle Check Pattern
Broken lines
White lines
Click here to return to step x to perform Head Refreshings