Fully charged. Power indicator on. Why doesn't it move?

Question edited for clarity, full make model (what it is).

Did you follow Section 9 about fully charging the battery, pressing and holding the button?

Charging Instructions 1. Plug the charger into the mains - the charger indicator light will be green.
2. Turn on the battery by press and holding the power button until the green light is illuminated.
3. Plug the battery into the charger. The charger light will turn from green to red to indicate the charging process has started.
4. Once the battery is fully charged, the charger status light will be

https://www.powakaddy.com/wp-content/uploads/2021/02/LATE-2022-FX3-OWNERS-MANUAL_01b.pdf

If that doesn't fix it, it will be a warranty issue. Click Support on top left.

https://www.powakaddy.com/manuals-and-instructions/

..

Reengage the wheels again then give it a slit push you should fell some resistance .seems the freewheel is not fully in

Hi whats the problem ? you mean your phone could not start up,or it is totally dead ? For nokia 5310 sometimes this problem cause due to im-proper connection of its battery,the connector of the battery gets open frequently,so first check it out Or if the battery fully drains.Put another battery and try,even if there is no effect insert charger.And if the charging is indicated the fault is power key.When charging indicated and your phone doesn't switch on then you need to change the Strip (Pata).Neverthless,contact mobile repairing shop.Thanks for visiting fixya.Good luck

Make sure the free-wheel lever is engaged and the charger is unplugged from the scooter before you try to turn the scooter on. If the battery gauge goes up when you turn the scooter on and there are no beeping sounds you should be good to go.If the battery gauge drops to the red when you try to accelerate slowly, your batteries are shot. (Typical replacement in 24-48 months).If there is any beeping when the key is first turned on then there is a problem and the number of beeps indicates the problem found by the computer during the POST. [Power On Self Test]

The meter on the charger indicates how much power the charger is putting out. The far left is zero (0) output, meaning fully charged. There should be numbers on the meter.

hi Richard,

Does the scooter actually lose power after the 3 leds show ?

If it is losing power then a suggest to try some other batteries to confirm dodgy batteries, check the terminal connections etc.

If it does not lose power then the volt meter is at fault, if you can check the voltage before riding then after it shows only 3 leds , if there is a big drop, check the charger first to make sure the batteries are getting fully charged.

Regards
GeWiz.,

i have the same exact problem on 1 of my sons MX5s..i checked all 3 batteries and all that! you left out the controller clicks when the back wheels sapose to be moving ,it's not....so worse case scenerio batt,controller,motor,(650 This time)& throttle....So theres our blue print...lets hope it's just the batteries....!

On a Nuvi 200W, when you plug in the charger, the battery status icon should go away indicating that you are no longer on battery power and that you are now running on an external power source. You should also hear a beep when you plug in the charger.

To go into charge mode, move the on/off switch to the left like you would be going to turn it off but only hold it on long enough until you hear it beep or the screen goes black and says "Battery Charging". When the battery is fully charged, touching the screen, it should say "Battery Charge Complete". If its not fully charged, touching the screen, it will say that it's still in charge mode.

- Jim
SHARCNET-USA

From the manual:

"Attach the barrel tip of the AC Charging Adapter to the AC Charging port of the POWER TO GO® and plug the standard two-prong plug into an appropriate, functioning 120 volt AC outlet. The red Battery Status LED indicator will flash, indicating a proper connection has been made and the unit is charging. The green Battery Status LED indicators will gradually light as the charge level rises. The POWER TO GO® must be charged for approximately 11-17 hours prior to first use. All Battery Status LED indicators will be lit solid (the red indicator will stop flashing) when the unit is fully charged.

Connect the supplied AC/DC adapter/charger to the 5V DC jack on your hdd and the power supply. The AC power icon will indicate on display showing that the Jukebox is now adapter operated. It takes 4 hours to fully recharge the hdd and once the battery is recharged fully, the jukebox can play up to 10 hours of music on the move