I have a jensen Je 1911 dvdc, it will not stay on but 8 seconds help we have 8 days left

Paste what into where? My assumption is that you have a "Dynamic link library", or dll for short, called 1911.dll.

My second assumption is that you are probably trying to paste it into the system32 folder.

But what version of Windows are you using? Windows xp, Vista, 7, 8, 8.1? (I would hope not older than XP).

This information is needed to guide you. please tell us on what version of windows you want to put it, and in what folder.

For anyone who has locked their Jensen TV mistakenly. To unlock it:
1. TV On (Using remote)
2. Press and hold the display button on the remote for about 2 - 3 seconds.

Are you asking how to clean an ACP 45, 1911 style? If so, its just a matter of removing the clip. Removing the slide, then removing the barrel and spring.

1) MAKE SURE IT IS UNLOADED!!! (cycle the slide several times)
2) Remove clip and Cycle the slide again to verify empty!
3)There is a pin just above and forward of the trigger mech on the frame of the pistol. One side of the pin will be rounded and protruding from the right side of the gun. On the left side of the frame will be a small flat arm that is connected to it the pin. Push the body of the slide towards the hammer (approx 1/8-1/4 of an inch) and you should be able to remove the pin out of the frame (towards the left side of the frame), it might take a bit of wiggling to get it out. All the while, continue with backwards pressure on the slide.

Once the pin is out the slide can move forward and can be removed from the gun.

4) At this point the barrel/ spring and trigger mech will be exposed. You can remove the barrel and spring for proper cleaning of the frame, trigger, barrel and spring. Then relubricate all components.

5) Reassemble in reverse order.

Good Luck

hold down clock button for about 3 seconds. then use tuning button ( bottom left ) to set hours and minutes move left for hour move righy fo minutes

The 4 second ticking indicates the battery is in need of replacing.

A professional watchmaker can properly replace the battery for you.

Hope this helps,

Ken
Yellowstone Watch, Inc.
www.yellowstonewatch.com

This is low battery warning. Replace the battery and the watch will tick as new.
Rate me, please

If you legally have it they shouldn't charge. If you don't what do you expect? They have to make money to stay in business.

My Advent TV did the same thing. Blue Screen with a red lock in the upper left corner. Just press and hold the display button for about 10 seconds. It will clearn

We have an Jensen JiMS-200 and it's a ipod docking station, which has a clock in it. We got no instructions in the box and have no idea how to change the time. I have searched the net without any success... Chez

I have this same amplifier. I have noticed several ways it will "not work" during my ownership of it. I have it connected to a seperate battery to save my alternator, battery, etc as it is a power hungry beast for how low the output wattage is. Test the input voltage to see if you have enough, one way to see this is to check the "jensen" emblem that lights up. If you dont have enough power it will appear dim and only the right side lights up. Also the amplifier will not work if your speakers are "blown" even a little bit. Ive taken speakers that wont work on my lxa400 and connected them to a higher power amp and they will work (although they will sound horrible) If youre smart you will keep the gain under 3/4 on this amp, I see some people have found out the hard way that full gain fries the amplifier circuitry. Not an expert on electronics but it smells somewhat like melting glue or plastic. Ive noticed a lot of people have problems with the RCA jacks as well. There are 8 jacks, in two clusters. The first one is A+B and the second is C+D. Note: You do not NEED Y connectors on this amp! Connect your output rcas from the deck to top left and bottom left jacks of the left cluster. This will give you left and right (a+b) output from the first set of speaker outs. Then connect an rca patch cord from the top right and bottom right jacks of the first cluster and connect the other end to the top left and bottom left of the second cluster. This will give you output from the second set of speaker outs. Remember that this is in 4 channel mode. I dont remember the set ups for 3 channel but two channel I believe is the left deck rca goes to top left of the first cluster and the right deck rca goes to the top left of the second cluster. Then you just wire the speaker outs according to the picture on the amplifier. something like this: _________________________ |(+) - (-) +| ~~~~~~~~~~~~~~~~~~~~~~~~~ Speaker + goes to (+) and speaker - goes to (-) Also addressing another issue if you want to increase the wattage to your speakers you just use a lower resistance speaker (2ohm instead of 4) I would not recommend using anything over 4 ohms. As for the high level inputs, I dont recommend using them unless you have the plugs that go with them, its a lot easier to wire your deck rears to a line converter (changes straight speaker wire to RCA jacks) or to just buy a new deck with RCA outs. Last item, common knowledge: 400 watts does NOT mean 400 watts!!! This amplifier puts out very little actual wattage (50 or 83 per channel depending on the load) Hope all this helps someone out there.. Anyone who knows the 3 channel setups I would appreciate it.