Model RB215LABP reset temperature display after power outage

The 33E error can indicate a problem with the ice maker water fill tube heater. (This makes sure that ice doesn't form and cause the fill tube to break.) To attempt to reset the error, press and hold the Energy Saver and Lighting keys on the touch pad for 8+ seconds. These are the top buttons on each side of the temperature display.

If that reset doesn't help, you need to replace the left door. That is available here: http://www.searspartsdirect.com/model-number/rf323tedbsraa0001/1482/0161000.html . It's part 1.

I hope this helps.

Cindy Wells

compressors use a small start / run capacitor to start the compressor
modern fridges do not like spikes from power outages and many power boards and electronic components fail because of this and I am inclined top use a surge protector before the fridge cord plug
I went google and typed in --fault code 88-88 for samsung fridge model rf26aewp and the first site up is error codes /messages/ blinking
the site is support-us.samsung>popup>iframe
there is a detailed answer there with a list of fault codes as well and what they indicate
there are other sites that also refer to the fault that you have

Hello Wayne, thank you for allowing me to assist you. Was the freezer unplugged during the power outage? If it was, here are some simple troubleshooting steps you need to take:

It is best to unplug the unit and wait for the power to come back on.

Next, turn the control to off (or digital display), plug the unit in and reset control to factory-suggested setting.

Do not open freezer door unnecessarily if freezer is off for several hours. Make sure the refrigerator plug is tightly pushed into electrical outlet and not plugged into a GFI.

If your unit has no power and it is not due to a power outage, check the following:

Verify that the temperature control is set to the OFF position.
Set temperature controls to proper setting suggested by your owner's guide; or set to the halfway point and adjust it up or down as needed.

If these basic troubleshooting tips prove ineffective, the power loss may have possibly caused a communication problem with the control board, temperature control or wiring harness. At this point, I would recommend having a service technician to diagnose the problem before investing in unnecessary parts.

I had a Wolf 30F wall oven with a similar problem
after power outage. It wouldnt stop beeping with error message related
to temperature control. My solution was to turn power of at circuit
panel, then reset by pressing and holding the clear button for 5
seconds.

Also note: in my case I had to close the display
before switching the panel off. When I tried to the reset process with
the panel showing, it wouldn\'t reset.



To reset other
various parts of the control panel Instructions said:



Time-of-Day Clock

Immediately after the oven is installed, set
the 12-hour clock to the current time of day. It may need to be reset
after a prolonged power failure. The clock is visible on the control
panel during all modes. If the upper oven timer is set, the clock will
not be visible in the upper oven control panel display.



SETTING CLOCK

1) Touch CLOCK.

2) Touch number pads to
set current time of day.

3) Touch CLOCK or ENTER to start
clock.



24-HOUR CLOCK

The time-of-day clock can be
changed from a 12-hour clock to a 24-hour clock. After the clock has
been set, touch TEMPERATURE for three seconds, touch CLOCK, and then
touch ENTER. Follow the same sequence to change back to the standard
12-hour clock setting.



Fahrenheit to Celsius

The
oven can be changed from Fahrenheit (°F) temperature to Celsius
(°C).

Water inside tank-type water heater can remain hot for some time.
That's one advantage of well-insulated tank-type water heaters.
http://waterheatertimer.org/9-ways-to-save-with-water-heater.html

Power outage can be related to failure of gas control.
Unplug stuff when power goes out. And then plug back in after power is restored.
Water heaters with electronics are not protected from surge.
Electronics can blow out during and after power outage. For example nearby lightning strike will cause current to run along household wires. With ordinary power outage, once power is restored, the surge can affect all kinds of electronic circuitry such as timers, water heaters, water softener, treadmill etc.

Sounds like you have intellivent gas control valve:
Open following link to identify gas control, and download typical manual, and download intellivent service manual with troubleshooting, error codes, etc.
http://waterheatertimer.org/How-to-adjust-temperature-on-water-heater.html#intelli

Take a moment and vote on answer:
And take advantage of fixya expert assistance live.
For a price, expert works with you while you work on water heater or any do-it-yourself project.
Fixya is always less expensive than a service call.

Information on the care of your product and troubleshooting is available here:

http://www.oasisleisure.ca/customer_care/SpaCare.html

Did you have a recent power outage? It is necessary to reset the temperature after a power outage.

Check the temperature setting on your hot tub; if it has defaulted do to a power outage reset to the desired temperature. If it is still set at your desired setting and is operating at 68 degrees then there is a problem that is preventing the tub from reaching the set temperature.

Some possible causes and actions are:

Pull filter (see if light comes on) / Replace filter
Knife valves not fully open / Open knife valves

Pressure switch cut of calibration / Adjust pressure switch
Faulty Pressure Switch / Replace pressure switch

Air leak, check pump suction line / Tighten pump union
Heating element corroded / Replace element

Faulty control panel / Replace panel

Find the Manual for you specifc model for more explansyion on Troubeshootig.

enter code 14 for reset

u need a a new defrost heater , it is not defrosting so it ices up the airducts

Here's the reset procedure.

1. Turn OFF the Main Power Switch.
2. Turn Main Power Switch ON again while pressing the Utility/Counter key more than
10 seconds after.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. Turn off the Main Power Switch and turn it on again more than 10 seconds after, and
make sure that the machine properly starts.

And yes, a power outage could cause this.

if it is anything like a monitor - look on the right side bottom for a slider - reset temperature adjust. just move the slider to a lower temperature. if you have a power outage, the display starts to flash 88:88