I hav whirlpool accubake.oven wont stay lit.it ignites then flame goes right back out

the igniter could be bad if having hard time to relite once lit should stay lit until set temp should relite automatically when needed

Whirlpool Gas Oven Will Not Stay Lit - Appliance Repair Forum

forum.appliancepartspros.com/oven.../482851-whirlpool-gas-oven-will-...

Jun 20, 2012 - 2 posts - ‎1 author
My Whirlpool gas oven will light but not stay lit. It has a glow plug igniter that heats up enough to allow the gas valve to open. Once the burner ... oven lights, but does not remain lit
10 posts
Feb 19, 2013
Oven does not stay lit
10 posts
Jun 19, 2012
Oven will ignite but will not stay lit
4 posts
Aug 3, 2010
Gas Oven won't stay lit
10 posts
Mar 25, 2008
More results from forum.appliancepartspros.com

is the flame sensor positioned in the flame where it changes to bright blue near the flame tip

I offer free advice bcuz God is so good!
GAS OVENS
The spark igniter tip is dirty (can clean it with either a little wire brush or a piece of fine sandpaper).
2) The Pilot flame is too low, and the tip of the igniter is not in the flame good enough. (the flame acts as a circuit when it touches the tip & completes the circuit).
3) The spark module is no good and needs to be replaced.(But 1 & 2 are your best bet).
spark module does not sense the flame when it's on. The spark igniter is also the flame sensor which provides feedback to the spark module.

Make sure the igniter is properly aligned with the burner lighting holes and it is clean. All lighting holes must be clean too. You can enlarge them using a drill bit one size bigger.

If it would not fix the problem, replace the bake burner and the igniter.
There is a small chance for the spark module itself to be bad as well.

The oven safety valve
(also called the gas valve) is the part that ensures that gas is not released until the igniter has reached the correct temperature needed to ignite the gas. While this part can fail, it is uncommon. If the hot surface igniter does not glow you should first verify that you have voltage to the circuit. This is a live voltage check and should be performed by a qualified person. If voltage is lost at the valve terminals then you should verify the continuity of the bi-metal in the valve using a multi-meter.


ELECTRIC OVENS:

CHECK THE OVEN RELAY CONTROL BOARD Aclicking sound could be something wrong with a relay. Check for any loose connections around the main control board on your oven. The click you hear is a relay losing power and switching back on. If the clock resets then something is causing power interruptions to the board.

: I offer free advice bcuz God is so good!

Good Morning! Do you have the model number of your appliance? With that we can better assist you.
Thank you!

What do you mean that it wont stay on? Does it turn off and on during cooking? Does it just go off and wont come back on? The oven thermostat regulates the heat in the oven and the oven element and the oven indicator light will turn off and on during cooking. If it stayed on constantly on full oven element power everything would burn.

The flame sensor has to prove the flame to stay lit. When it fails, the valve closes.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

I have a whirlpool accubake system / super capacity 465 oven ... the top burners do fine...but my oven pilot went out... and I don't know how to re-lite the pilot... the owners manual doesn't help ... it doesn't show anything a layman could understand ... no visual illustrations ... when I turn on the oven ... the display shows that it's been activated... it clicks a couple of times but does not light ... what is a simple way to re-light the pilot? thanks, A

i have a whirlpool gas accubake range and only two burners will ignite. The other two burners make a clicking sound and release gas but never light. I have to use a match to light the other two burners and the flame is uneven on one. What should i do?