Someone at our company raised the lid on the Keurig too high and its locked in place. How do you get the lid to close or unlock?

2018 Speed Queens did not have lid locks. The 2019 machines do. The lid lock can not be disabled. If the lid is stuck closed, you can, with 30 pounds of pressure, raise the lid without damaging the lock. (unlike any other machine on the market)

Try cleaning were it closes

The company had a major recall and went out of business. No manuals appear to be available on the web.
Here are some general instructions you can use:

1 Set up your cooker. Place your Ultrex Pressure Cooker on the stove. Remove the lid and pour in no more than 2 inches of water. Depending on what you are cooking the amount of water will vary. More water will ultimately cook larger amounts of food, but you will need to refer to your specific model's instructions on this matter.

2 Put in the food you wish to cook. Close and lock the lid firm to the pot. Make sure it is locked securely so none of contents boil out of the top.

3 Turn on your burner to high heat for approximately ten minutes. Allow the water to boil.

4 Turn the stove down to a low setting after the water is boiling in the cooker. Flip the pressure valve closed and allow your food to simmer.

Set the pressure valve to ten pounds. For vegetables, cook 30 to 45 minutes. For meats, cook 45 to 60 minutes.5

6 Open the pressure valve and allow the pressure to discharge. Unlock and remove the lid to find your fully cooked meal.

Try taking the water jug off again and try closing it

Usually a locked draw is caused by an electronic controller failing.To open the draw you can pull it with even firm pressure but do not try and close it as thelid is in the "down "position.Before closing you must go inside chassis by pulling out the affected draw ,unclip the lid motors from the lid supports and push the lid up to the raised position and then wind the arms of the lid motors to the new height,manually and then clip the lid motor arms back into the lid supports.Then replace the draw.Then you must replace the electronic controller...

It takes about 3 minutes to brew. You cannot use a clear coffee mug (scensors won't detect it)

You should be able to turn it on, Then place k-cup in holder, Then close lid and water reservoir lid will pop up and you add desired amount of water. Then push lid down, place mug under spout and the blue light will light up and you push taht. Within 3 minutes you should have some coffee

Magnetic reed switch on left side below the gray rubber bumper, shown here...

http://www.repairclinic.com/SSPartDetail.aspx?PartID=1033130&PPStack=1

Release two spring clips in front between main top and front panel using putty knife. Lift the main top and access the left and right door locks here.

To access and see if the magnet is in place, remove the dispenser from lid.
Gently pry the bottom of the plastic inner lid toward you then down. This will let you see if the magnet is in place on the right front corner of the inner lid.

http://fixitnow.com/wp-content/uploads/2006/09/washer_switch.JPG

Seems to be a common problem with this washer. Apparently, the lid isn’t completely watertight and allows water to get into this switch corroding the contacts and the wires.

Thanks for using FixYa - a Very Helpful rating is appreciated for answering your FREE question.

you have to loosen the hood hinge where the lock is and move the lock ring lower to get the lid close tighter, if the car was damaged by an accident then you will have to get it repaired by a body shop or by someone who can find the high spot that it is hitting.

ck lid screws especially on newer models on these the lid switch is located left rear corner just behind lid hinge if switch is on right side close lid slowly and listen for click if none heard try pressing down on lid at switch location if washer starts replace switch if switch lever broke change switch..on other type switch lower lid slowly and listen for click if none heard and hinge screws ok raise lid and push lid hinge toward back slightly and try again still no click raise console switch is on left and just snaps in place

the promblem is that when the top is raised that the wire to the lock motors is hhot on both sides so the motor doesn't no to open or close and the rear hatchwill not come down