Power wontcome on - Televison & Video

Battery may have failed and needs replacement.

insert the radio code.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.




*This originally came from abauto

Remove upper and lower covers. The top is tricky because the ears of the ignition keep the top cover from being removed. I take a razor blade and cut the plastic all the way through directly in the middle below the ears of the ignition. Be aware of hidden screws when removing the covers. The screws are small inverted torx.

After getting the top cover off. With key in On position. Look for hole with depress pin in it. Press retainer with pick or similar and pull tumbler straight out.

U have a failed hydraulic clutch master or slave cylinder, it is best to replace the pair.

Safety interlock switch sounds bad.

The product uses a power cord, if the power supply is a power cord with electrical connections at each end. Figure 1: Power cord The product uses a power module, if the power supply is a power cord connected to a power module. Figure 2: Power module

• If the product uses a power module (adapter), go to Step two: Check if power is supplied from the power module.
• If the product uses only a power cord, go to Step three: Check if power is supplied from the power cord.If the product uses a power module (adapter), follow these steps to make sure that power is properly supplied to the product. Figure 3: Power module
  1. Check the power module part number against the part number listed in the User’s Guide to make sure that the proper power module is being used.
  2. If the power module has a permanently attached power cord, do the following.
     1. Disconnect the power cord from the wall outlet.
     2. Disconnect the power cord from the product.
     3. Wait 30 seconds.
     4. Reconnect the power cord to the product and the wall outlet.
  3. If the power module has a detachable power cord, disconnect the power cord from the power module and reconnect the power cord to the power module.
  4. If the power cord was plugged into a surge protector or power strip, plug the power cord directly into a wall outlet instead.
  5. If the product does not turn on, or the power light built into the power cord does not glow, plug the product into a wall outlet in another room.
     • If the product or power light turns on when connected to a wall outlet in another room, there is an issue with the power supply in the previous room.
     • If there is still no power to the product, then the power module, power cord, or product might be defective. Proceed to the next instruction.
  6. Connect the power module or power cord to another HP Deskjet or Photosmart product to see if the power module is functioning.
     • If the power light does not glow, the power module might be defective. Replace the power module and the power cord.
     • If the power module or power cord works on the other product, the product facing the issue might be defective. Proceed to Step four: Service the product.

If the product uses only a power cord, follow these steps to make sure that power is properly supplied to the product. Figure 4: Power cord

1. Inspect the power cord for visible damage.
   • If the power cord is damaged, replace the power cord.
   • If the power cord is not damaged, continue with the next instruction.
2. Disconnect the power cord from the wall outlet.
3. Disconnect the power cord from the product.
4. Wait 30 seconds.
5. Reconnect the power cord to the product.
6. Reconnect the power cord to the wall outlet.
7. If the power cord was plugged into a surge protector or power strip, plug the power cord directly into a wall outlet instead.
8. If the product still does not turn on, plug the product into a wall outlet in another room.
   • If the product turns on when connected to a wall outlet in another room, there is an issue with the power supply in the previous room.
   • If there is no power to the product, then the power cord or the product might be defective. Proceed to the next instruction.
9. Connect the power cord on another HP Deskjet or Photosmart product to see if the power cord is functioning.
   • If the power cord does not work on the other product, the power cord is defective. Replace the power cord.
   • If the power cord works on the other product, the product facing the issue might be defective. Proceed to Step four: Service the product.

Step four: Service the Product If you have completed all the steps listed above and are still experiencing a problem, service the product by calling hp at 1800-474-6836

probably its one of the door switches thats defect and wire grounds intermittently and dome light stays on!

take the battery out then put it back in it should work then