Wash doesn't go through full cycle

To open door during mid cycle, turn off washer by plug and wait a couple of minutes until you hear a click, then the lock light ( assuming it has one ) will release, but make sure there is no water in the tub before opening the door. If possible when door is unlocked, run the drain setting and let the water pump out before hand. Hope this helps.

see this steps and fix it. God bless you

Lid Switch Assembly

If the washer stops mid cycle the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.


Enter your model number to see parts for your washing machine.
Help me find my model number

Door Lock Motor and Switch Assembly

If the washer stops mid cycle the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.


Enter your model number to see parts for your washing machine.
Help me find my model number

Water Inlet Valve

If the washer stops mid cycle the water inlet valve cold water side may have failed. Most washers have a cold water rinse and so if they can't fill with cold water they just sit indefinitely waiting for the cold water to enter. If there is cold water to the water inlet valve and the cold water works in other parts of the cycle - or to make warm water - the valve is not the problem.


Enter your model number to see parts for your washing machine.
Help me find my model number

Main Control Board

If the washer stops mid-cycle the main control board might be defective. This is not common. Check other causes first such as the lid or door switch and other components.


Enter your model number to see parts for your washing machine.
Help me find my model number

Timer

If the washer stops mid cycle the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

follow this steps and fix it. God bless you

Lid Switch Assembly

If the washer stops mid cycle the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.


Enter your model number to see parts for your washing machine.
Help me find my model number

Door Lock Motor and Switch Assembly

If the washer stops mid cycle the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.


Enter your model number to see parts for your washing machine.
Help me find my model number

Water Inlet Valve

If the washer stops mid cycle the water inlet valve cold water side may have failed. Most washers have a cold water rinse and so if they can't fill with cold water they just sit indefinitely waiting for the cold water to enter. If there is cold water to the water inlet valve and the cold water works in other parts of the cycle - or to make warm water - the valve is not the problem.


Enter your model number to see parts for your washing machine.
Help me find my model number

Main Control Board

If the washer stops mid-cycle the main control board might be defective. This is not common. Check other causes first such as the lid or door switch and other components.


Enter your model number to see parts for your washing machine.
Help me find my model number

Timer

If the washer stops mid cycle the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

Hi Guys,

My Lamona washing machine is also stuck on rapid wash? Dis you get it resolved?

Kind Regards

that is correct ,. pump water out then the door will open.

If this is a front load washer, yes it's normal.
You wouldn't want your laundry and all the water falling out on the floor because the door didn't lock, would you ?

unplug the washer an the door will open

Hello- If the drum does not turn in either wash or spin I would check the belt drive.

TURN MACHINE ON TO FINISH CYCLE THEN RE WASH WITH SOAP ETCH,DOOR WILL NOT OPEN MID CYCLE SAFTY LATCH,YOU CAN TURN PROGRAM TO FINAL SPIN TO EMPTY MACHINE AND FINISH PROGRAM THEN DOOR WILL OPEN

Sounds like the door lock unit isn't locking and may be bad. It is also a possiblity but not likely that there could be a problem with the computer board but start with the door lock unit first