Question about Whirlpool Cabrio 7.0 Cu. Ft. Super Capacity Plus Electric Dryer

1 Answer

Moisture sensor location and picture of moisture sensor

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 137 Answers

Posted on Nov 20, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Samsung frontload gas dryer DV218AG moisture sensor doesn't work properly. Dryer adds minutes to drying cycle even when cloths are completely dry.


Clean the sensors with windex or like cleaner. Farbic soften can build up on the sensors and cause you trouble, Also, the time displayed is an estimate not actual drying time.

Jan 26, 2014 | Samsung Dryers

1 Answer

Moisture sensor location


Never heard of it.
What's the actual trouble code ?

Jan 20, 2014 | Dodge Cars & Trucks

1 Answer

Where is the sensor located on a lg tromm elect dryer


The moisture sensor is located in front grill area inside the dryer. If you look inside the drum where the filter screen mesh is, you will find 2 curved metal bars. Those are your moisture sensors.
Hope this helps.

Nov 06, 2011 | LG DLE5977 Electric Dryer

1 Answer

Where is the moisture sensor on a GGW9868KQ5


It is located inside and behind the lint screen. Here is a picture to show you what it looks like.

Jan 18, 2011 | Whirlpool Dryers

1 Answer

Camera has a black LED screen when in the shooting mode. If a picture is taken it also is black. Previous pictures can still be viewed from the memory stix.


probably ur sensor is dead or there is dirt and moisture accumulation over ur sensor.... it is a mechanical cover and the dirt-moisture ghlue is preventing it from opening and stimulating the sensor. take it to prf repairer and get the dirt removed.

i had the same problem with my POWERSHOT A610

Dec 18, 2009 | Canon PowerShot G10 Digital Camera

2 Answers

Error code c2100


your vcr is having condensation symptom.you can try 1,let it on for 2 hour, 2, you can open the upper body then you can use hairdryer the mekanik near where you push the cass, the sensor near the left reel.

Apr 16, 2009 | Sony DSR-45 Mini DV VCR

1 Answer

Kenmore Gas Extra Capacity heats only on timer,not Fabric Master.


get some windex and clean the sensor strip located behind the filter ousing similar to this picture. Their might be something on it that is interfering with its moisture sensing ability. Check out my youtube channel about section for a link to a free dervice manual for you model. Thanks
2011-04-10_152724_dryer-moisture-sensor_330x200-j2rqmywrjn05nkl43ld3f3b0-5-0.jpg
Dan Webster

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61


Jun 18, 2017 | Kenmore 73952 Gas Dryer

1 Answer

Dryer turns off in 10 minutes.


To check the moisture sensors. Make sure the dyer is plugged in and all controls are set to off. Next to get into the diagnostic mode press more time, less time, more time, less time, all within 5 seconds. Now all indecator lights on the console are lit up with 88 in the " time remaining" display, if the test mode has been entered. Now this how to check the moisture sensors. Open the dryer door. You may hear a beep sound and the software revision number will be displayed on the console. If this happens there is a short in the moisture sensor system and the moisture sensors need to be checked and probably replaced. If this doesn`t happen,locate the moisture sensors on the face of the lintscreen housing and lay a wet cloth or towell across them. You should hear a beep and the software number will be diplayed on the console. If this happens then the moisture sensors have past the test and your problem is even deaper into the electronics and may reqiure a technician to trace this problem down.I hope this has helped you.

Nov 10, 2008 | Whirlpool GEW9200L Electric Dryer

1 Answer

Moisture Sensor Location


It could be the sensor. However, check the exhaust vent for restrictions first. you can test the moisture sensor Damp Dry Test 1. Set the following Timer- DAMP DRY Fabric Care/Temperature switch- COTTON HIGH Wrinkle Guard switch- OFF Signal switch- LOUD Door- must be closed 2. Press the PUSH TO START switch. After approximately 16 seconds, the Timer will start to advance to the OFF position, and the ?End of Cycle? signal will sound. If one or more of these functions do not occur, proceed to the Factory Test. Factory Test The Factory Test allows factory/service personnel to test and verify all inputs to the Even Heat control. The basic operation of this test is to notify the operator with an audible beep every time the status of an input to the control changes state. Activating the Test Mode 1. Set the following configuration: Door- must be open Fabric Care/Temperature switch- AIR FLUFF Signal switch- LOUD Timer- TIMED DRY OR AUTO MOISTURE SESING PLUS selection 2. Turn the Wrinkle Guard switch from OFF to ON three times within a five second period. A single beep will sound to indicate that the factory test mode is activated. NOTE: If any of these initial conditions are not satisfied, the control will not enter the test mode. Test Mode Functionality When the control is in the Factory Test mode, every input change of state will result in a beep (with the exception of the Signal switch). This includes: Door switch Moisture Sensor (short/open Sensor will result in a beep) NOTE: A moistened finger or damp cloth may also be used. Fabric Care/ Temperature switch Wrinkle Guard switch Push to Start (PTS) switch (with the door switch closed) Timer (any cam input change will result in a beep) NOTE: Timer will advance during test. If any of the inputs do not result in a beep, proceed to the following component tests If the dryer shuts off too soon when set to the AUTO MOISTURE SENSING PLUS cycle, check the following: -HARNESS/CONNECTION -MOISTURE SENSOR -THERMISTOR -EVEN HEAT CONTROL Procedure: 1. Test the Moisture Sensor by following the procedure outlined in ?Factory Test?, beginning on page 3. If the Moisture sensor fails the ?Factory Test? (does not produce a beep sound), check the Moisture Sensor. a. If there is continuity to Ground for Yellow/Red (Y/R) wire with no load, look for a short in the Sensor or Y/R wire. Verify harness connections both at the Sensor and the Even Heat control. b. If the Sensor and Y/R wire are good, replace the Even Heat control. 2. If Factory Test passed, verify thermistor by performing test procedures outlined in ?Thermistor Test? 3. If problem persists after replacing Moisture Sensor and thermistor

Aug 27, 2007 | Kenmore 62972 Electric Dryer

Not finding what you are looking for?
Whirlpool Cabrio 7.0 Cu. Ft. Super Capacity Plus Electric Dryer Logo

Related Topics:

552 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dryers Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Donni Steen

Level 3 Expert

687 Answers

Are you a Whirlpool Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...