Display on printer flashes on and off, and tells me to turn printer off and on. I do this and display still flashes when I turn the printer back on and no controls are accepted.

Ansewer
#

Enter the Service mode following the procedure below.

1) Turn off the printer.

2) Turn on the printer while holding down the [Paper Source] button and [Information] button.

* Keep pressing the above buttons until "Initializing" appears on the display.

3) "S" is displayed in the upper right corner of the display showing the version.
4) After display of "Online", pressing the [Menu] button displays the SERVICE MODE top menu and the MESSAGE LED flashes.

try to check carriage , if there is nothing , mean formatter is faulty

6C10 means you need to replace the ink absorber. After this it require to reset the error. Reset 6C10

This should help:

http://www.cameras.co.uk/cameraimages/fuji-finepix-Z20fd-back.jpg

Display button is DISP

Call sawgrass tech support for the reset.... it is straight forward and easy to follow. As per customer support, you will need better than 20% full cartridges, they recommend new ones, which they will provide overnight free if still warranted.(ERR28212) As discussed, here are the reset instructions.
1. Turn the printer off.
2. Open the cartridge door and leave it open until step 15.
3. Turn the printer back on.
[img id="Picture_x0020_1" alt="3110 Panel" src="file:///C:/Documents%20and%20Settings/Nancy%20Smith/Local%20Settings/Application%20Data/IM/Runtime/Message/%7B944CD05A-8C76-404B-84B9-E5D3FB8CED31%7D/Show/image0011.jpg" width="500" height="143"> (was a photo of machine front, the down button is also "menu")
4. Hold down both the Up & Down arrows together for 3 to 5 seconds (nothing on the LCD display will indicate the appropriate amount of time has passed)
5. Release the arrow buttons and press #Enter (if nothing happens, try again)
6. When successful the LCD will display SYSTEMver with 3 optional menu selections starting with Service Menu
7. Press the down arrow once to Engine Maint. and press #Enter
8. The LCD will display SP No. with the default 1000000 underneath
9. Using the Up & Down arrows, and pressing #Enter after each number, enter 3009002. Press #Enter when complete.
10. CARRIAGE CHANGE 3009002 will display on the LCD. Press #Enter.
11. CARRIAGE CHANGE EXEC will display on LCD. Press #Enter.
12. OK? will display on the LCD Press #Enter.
13. Then Running will flash on the LCD panel before going back to CARRIAGE CHANGE EXEC. Continue to next step.
14. Exit the SP mode by pressing the Escape button repeatedly until you are back at the Engine Maint. screen. Press the down arrow once to End. Press #Enter one more time to completely exit.
15. Turn the printer off.
16. Replace the four ink cartridges with new ones.
17. After the new cartridges have been installed, close the right front cover.
18. Turn the printer on.
19. Wait for the machine to fill go through an initialization procedure which may take about 7 minutes.
This 100% worked for me.... be certain that the screen displays EXACTLY what the directions tell you!! -NSmith

At back camera, have lamp flashes orange where to indicate flash is charging and to tell image will not recorded(disable). You will can not take another flash until that lamp is stop flashing orange to indicate charging is full. in other view, please check at lcd screen have appear flash icon.
click button play mode to display menu. change set flash to on if flash icon is not display


for user manual

User manual trobleshoot

Take the unit back to where you bought it, and get them to replace the defective unit.

The question is what light is flashing? One thing you can do is turn your system off. then unplug your system from your wall outlet...wait 15-30 seconds...plug it back in and then turn on your system..this may work out wise I need to know what light is flashing on your display.

try switch off, unplug, hold up and down & reset button at the back, swith on

Hi,

Find this in the web

http://h10025.www1.hp.com/ewfrf/wc/document?cc=hk&docname=c00489814&dlc=en&lc=en&jumpid=reg_R1002_HKEN

Use the instructions below to resolve the issue by restarting the product.

1. Disconnect the Universal Serial Bus (USB) cable from the back of the product, but leave the product turned on.
2. Open the cover of the product and remove the print cartridges.
3. Close the cover and wait for the Insert Ink Cartridges message to display.
4. Disconnect the power cord from the back of the product and wait for one minute.
5. Reconnect the power cord. If the product does not automatically turn on, press the Power button.
6. Open the cover and reinsert the print cartridges.
7. Close the cover. If prompted, print a calibration page.
8. Reconnect the USB cable, and try to print a print job from the computer.