Check performance - Dell Desk Top Computer--and Lcd Monitor 17 "

Question edited for clarity

https://www.copytechnet.com/forums/toshiba/142847-toshiba-estudio-3508a-error-f101-1-a.html

HDD, SYS board, Setting 1. Turn the power of the equipment OFF and check the
connection of the HDD.
- Connector and harness check
- Check if the connector pins of the HDD are bent.
- Check if HDD for other equipment is not installed.
- Check if SRAM for other equipment is not installed.


2. If the error still occurs after step 1, perform the following.
- Perform HS-73 Firmware Assist mode -> Key
Backup/Restore and check that each Key Status is
"OK".
- If not, recover the key (press [Key] and select the
menu, and then press [Execute]).


3. If the error still persists after step 2, perform the
following.
- Perform HS-73 Firmware Assist mode -> Format
HDD, and then install "System software" (HS-49
Firmware Update mode -> SYSTEM SOFTWARE
(HD Data)).
Notes:
The following items will be deleted by HS-73
Firmware Assist mode -> Format HDD.
• Message Log
• Job Log
• Spool Data (Print, Email reception)
• Template
If F101_1 occurs with secure HDD or the error
persists after performing step 3, perform step 3 after
performing HS-74 HDD Assist mode -> Revert
Factory Initial Status HDD.


4. If the error persists even after step 3, replace the HDD.


5. If the error persists even after step 4, replace the HDD
harness.

https://www.google.com/search?q=Toshiba+estudio+4508A+has+an+error+code+of+F101

..

1. Turn the power of the equipment OFF and check the
connection of the HDD.
- Connector and harness check
- Check if the connector pins of the HDD are bent.
- Check if HDD for other equipment is not installed.
- Check if SRAM for other equipment is not installed.
2. If the error still occurs after step 1, perform the following.
- Perform HS-73 Firmware Assist mode -> Key
Backup/Restore and check that each Key Status is
"OK".
- If not, recover the key (copy "SRAM Key Status" to
"FROM Key Status" or vice versa).
3. If the error still persists after step 2, perform the
following.
- Perform HS-73 Firmware Assist mode -> Format
HDD, and then install "System software" (HS-49
Firmware Update mode -> SYSTEM SOFTWARE
(HD Data)).
Notes:
The following items will be deleted by HS-73
Firmware Assist mode -> Format HDD.
• Message Log
• Job Log
• Spool Data (Print, Email reception)
• Template
If F101_1 occurs with secure HDD or the error
persists after performing step 3, perform step 3 after
performing HS-74 HDD Assist mode -> Revert
Factory Initial Status HDD.
4. If the error persists even after step 3, replace the HDD.
5. If the error persists even after step 4, replace the HDD
harness.
6. If the error persists even after step 5, replace the SYS

1. Turn the power of the equipment OFF and check the
connection of the HDD.
- Connector and harness check
- Check if the connector pins of the HDD are bent.
- Check if HDD for other equipment is not installed.
- Check if SRAM for other equipment is not installed.
2. If the error still occurs after step 1, perform the following.
- HS-75 File System Recovery mode ? Recovery F/S ? /
imagedata, and then restart the equipment.
- Perform FS-FAX ? 11 FAX CLEAR MODE ? [CUSTOM
INITIALZE] ? [CLEAR DATA], and then restart the
equipment.
3. If the error persists after step 2, perform the following.
- Perform HS-73 Firmware Assist mode ? Format HDD, and
then install "System Software (HD data)" with HS-49
Firmware Update mode.
Notes:
The following items will be deleted by performing HS-73
Firmware Assist mode ? Format HDD.
• Message Log
• Job Log
• Spool Data (Print, Email reception)
• Template
4. If the error persists even after step 3, perform the following and
then reattempt step 3.
- HS-74 HDD Assist mode ? Revert Factory Initial Status
HDD.
5. If the error persists even after step 4, replace the HDD.
6. If the error persists even after step 5, replace the HDD
harness.
7. If the error persists even after step 6, replace the SYS board.

PDF EVO Battery Instructions - Ballistic Performance Components

https://www.ballisticparts.com/pdf/BT0071B-instructions.pdf

starting procedures" video on our website: www.ballisticparts.com. WARNINGS ... your vehicle has trouble starting, check voltage of the battery and recharge the ...

Evo Battery Instructions - Ballistic Performance Components

https://www.ballisticparts.com/batteryInstruct.php

Congratulations on your purchase of a Ballistic Performance Components ... If your vehicle has trouble starting, check voltage of the battery and recharge the ...

[PDF]INSTRUCTION MANUAL - Ballistic Performance Components

https://www.ballisticparts.com/pdf/BT0071A-instructions.pdf

Please check voltage before installing to insure that your battery has at least 13.2 ...13.2 volts, please charge the battery according to the charging instructions ...

F101-4: Partition mount error (The HDD cannot be connected (mounted) caused by damage to the "/work" partition.)

1. Turn the power of the equipment OFF and check the connection of the HDD.
- Connector and harness check
- Check if the connector pins of the HDD are bent.
- Check if HDD for other equipment is not installed.
- Check if SRAM for other equipment is not installed.

2. If the error still occurs after step 1, perform the following.
- Perform [3C] - [5] (Key Backup Restore) and check that each Key Status is "OK".
- If not, recover the key (copy "SRAM Key Status" to "FROM Key Status" or vice versa).

3. If the error persists after step 2, perform
[5]+[C]+[POWER]?2. Recovery F/S?3. /work, and then restart the equipment.

4. If the error persists after step 3, perform
[5]+[C]+[POWER]?3. Initialize HDD?2. /work, and then restart the equipment.

5. If the error still persists after step 4, perform the following.
- Perform [3C] - [3] (Format HDD), and then install "System Software (HD data)" with [49] - [4].

Notes:
The following items will be deleted by performing [3C] - [3] (Format HDD).
• Message Log
• Job Log
• Spool Data (Print, Email reception)
• Template
If the error persists after performing step 5, perform step 5 after performing [4]+[C]+[POWER]?1. Revert factory initial status HDD.

6. If the error persists even after step 5, replace the HDD.

- The service mode functions are same as those of the previous models.
1) Test pattern 1: Service test print pattern 1 will be printed.
2) Test pattern 2: Service test print pattern 2 will be printed.
3) Test pattern 3: Service test print pattern 3 will be printed.
4) Cleaning at the service test print: Check the Cleaning box and perform the service test print.
Cleaning will be performed before the service test print is printed.
5) EEPROM initialization at the service test print: Check the EEPROM Clear box and perform the
service test print. EEPROM will be initialized.
6) Destination setting: Select the device ID to set the destination.
7) Ink absorber counter resetting (Main): Main ink absorber counter will be cleared.
8) Ink absorber counter resetting (Platen): Platen ink absorber counter will be cleared.
9) Device ID acquisition: Device ID will be displayed on the PC.
10) EEPROM information acquisition (Dump): EEPROM information will be displayed on the PC with
the HEX dump.
11) EEPROM information acquisition: EEPROM information will be displayed on the PC.
12) Nozzle check pattern print: Nozzle check patter will be printed.
13) Cleaning A: Cleaning A will be performed.
14) Cleaning B: Cleaning B will be performed.
15) Cleaning C: Cleaning C will be performed.
16) Cleaning D: Cleaning D will be performed.

Definition of Diagnostic Trouble Code P1346 Audi: Ignition Coil Power Output Stage 3 Short to B+ BMW: Misfire During Start Cylinder 3 Buick: Intake Camshaft Position [CMP] Sensor System Performance Cadillac: Intake Camshaft Position [CMP] Sensor System Performance Chevrolet: Intake Camshaft Position [CMP] Sensor System Performance Ford: Fuel Level Sensor B Circuit GMC: Intake Camshaft Position [CMP] Sensor System Performance Lexus: VVT Sensor Rang/Performance Problem (Bank 1) Lincoln: Fuel Level Sensor B Circuit Mazda: Fuel Level Sensor B Circuit Mercury: Fuel Level Sensor B Circuit Oldsmobile: Intake Camshaft Position [CMP] Sensor System Performance Pontiac: Intake Camshaft Position [CMP] Sensor System Performance Saturn: Intake Camshaft Position [CMP] Sensor System Performance Toyota: VVT Sensor /Camshaft Position Sensor Circuit Range/ Performance Problem (Bank 1) Volkswagen: Ignition Coil Power Output Stage 3 Short to B+

Hi ...

I would suggest you try and clean the print head and that should resolve the problem. Follow the below steps to clean the print head:

Perform a Cleaning of the print head:
Caution: Cleaning consumes a certain amount of ink. Perform Cleaning only when necessary.
Note: The pattern varies depending on the printer and version of Windows being used.

1. Click 'Cleaning' to perform print head cleaning from the Pattern Check window and proceed to step 3 of the print head cleaning instructions. If the Pattern Check window is closed, skip this step and proceed to step 2.
   
   
   
   
   
2. To perform a print head cleaning from the Maintenance window, click 'Cleaning'.
   
   
   
   
3. When the Print Head Cleaning window is displayed, select the target ink group for 'Cleaning'.
   
   
   Note: When performing Cleaning for all colors, check 'All Colors'.
   
   
   
   
   Note: When performing Cleaning for Black only, deselect 'All Colors' and check 'Black'.
   
   
   
   
   Note: When performing Cleaning for Color only, deselect 'All Colors', and check 'Color'.
   
   
   
   
4. After selecting the target ink group click 'Execute' to perform the cleaning of the print head nozzles.
   
   
   
   
5. When the confirming message is displayed, check the contents, and click 'OK'.
   
   
   Caution: Although the Nozzle Check window is displayed, do not perform any other operations until Cleaning is completed.. Cleaning will take about 40 seconds.
   
   
   
6. Print a Nozzle Check Pattern and examine.
   
   
7. Perform Cleaning again if necessary.
   
   
   Memo: If the pattern is still abnormal after two Cleanings, perform up to two Deep Cleanings.
   
   
   

Perform Deep Cleaning of the print head
Caution: Deep Cleaning consumes a larger amount of ink than normal Cleaning. Perform Deep Cleanings only when necessary.

1. In the Maintenance window, click 'Deep Cleaning'.
   
   
   
   
   Note: The layout varies depending on the printer and version of Windows you are using.
   
   
2. When the Deep Cleaning window is displayed, select the target ink group for Deep Cleaning.
   
   
   
   
   Note: When performing Cleaning for all colors, check 'All Colors'.
   
   
   
   
   Note: When performing Cleaning for Black only, deselect 'All Colors' and check 'Black'.
   
   
   
   
   Note: When performing Cleaning for Color only, deselect 'All Colors', and check 'Color'.
   
   
   
   
3. Click 'Execute'.
   
   
   
   Memo: By clicking 'Initial Check Items' before clicking 'Print Check Pattern', you can see the specific confirmation items in Nozzle Check.
   
   
4. When the confirming message is displayed, click 'OK'. (The Power lamp will blink green and Deep Cleaning starts. The blink stops when Deep Cleaning is over.)
   
   
5. When Deep Cleaning starts, check the contents, and click 'OK'.
   
   
   Caution: To prevent interruption of the Deep Cleaning process, do not perform any other operations until Deep Cleaning is completed. When the operation of the printer is stopped, Deep Cleaning is completed. Deep Cleaning will take about 75 seconds.
   
   
   
6. Print Nozzle Check again.
   
   
   Note: If the printed pattern is still not normal, perform steps 1 through 4 of the Deep Cleaning process one additional time.
   
   
   Caution: If after two Deep Cleanings the Nozzle Check Pattern is still not normal, turn the printer off and let it sit for 24 hours or more before attempting another Deep Cleaning again. The wait time may allow dried ink in clogged print head nozzles to liquefy, and resolve the problem
   

If this does not resolve the problem, please reply back and we'll try the next step ...

Don't forget to vote if this helps ... Cheers :)

Print Head Cleaning / Head Refreshing If the printed nozzle check pattern is broken, missing, or a specific color is not printed, clean the print head. NOTE:
a. Cleaning the print head consumes a small amount of ink. Cleaning too often reduces the amount of ink in the ink tanks.
b. Print head cleaning is performed when you connect the power cord. Your machine may perform print head cleaning periodically to avoid clogging.

1. Press <COPY> or <PHOTO>.
   
   
2. Press <Menu> repeatedly until <USER DATA> appears.
   
   
3. Press < (left arrow) or > (right arrow) to select [MAINTENANCE].
   
   
   
   
4. Press <OK>.
   
   
5. Use < or > to select [CLEANING] or [HEAD REFRESHIN] as necessary.
   
   
   
   [CLEANING]: Performs normal print head cleaning.
   [HEAD REFRESHIN]: Performs deep print head cleaning.
   
   
6. Press <OK>.
   
   
   
   
7. Print a Nozzle Check Pattern to see if print quality improved.
   
1. Press <COPY> or <PHOTO>.
   
2. Press <Menu> repeatedly until <USER DATA> appears.
   
3. Press < (left arrow) or > (right arrow) to select [MAINTENANCE].
   
   
   
4. Press <OK>.
   
   
   
5. Press <OK> again.
   The machine prints a nozzle check pattern (A).
   
   
   
   
8. If broken or white lines appear in the pattern, perform two Head Refreshings (from steps 1 through 6) then print another Nozzle Check Pattern.
   
   
9. If print quality does not improve after two Head Refreshings, replace the appropriate ink tank.

Confirming The Nozzle Check Pattern
Broken lines
White lines
Click here to return to step x to perform Head Refreshings

check to make sure the bag isn't being sucked into the air filter. open the access door where the bag is and you'll see the air filter at the bottom. to check, leave the door open while you would see the performance indicator light on, and then pull up the bag. this is one of many solutions i'm sure to the performance indicator problem.