How do I remove 3 button switch? - Jacuzzi Home

it doesn't have an external memory card that you can remove... it does have an internal though but removing it might completely break the phone...
you can refer to the link to checkon the complete specification of you phone: http://www.gsmarena.com/nokia_n81_8gb-2085.php
but you can reformat the memory to factory settings though:
reformatting NOKIA N Series phone:
simple ways to format your Nokia NSeries cell phones.
(Please do remember that some of the steps below will clean up all your data in phone so remember to make up backup copy of it. Otherwise you will end up loosing them forever.)
Method:1
1. Switch off the phone.2. Hold down the following three buttons: Green (call answer button, * button, and '3? button. 3. While holding these buttons, press the power button and switch on the phone. 4. When the message 'Formatting' appears on the screen, release all of the buttons.
Method: 2 ( Hard Format)
1. Switch off the phone.2. Hold down *#7370# button. 3. While holding these buttons, press the power button and switch on the phone. 4. When the message 'Formatting' appears on the screen, release all of the buttons.
Method: 3 Soft Reset
1. Switch off the phone.2. Hold down *#7780# button. 3. While holding these buttons, press the power button and switch on the phone. 4. When the message 'Formatting' appears on the screen, release all of the buttons.
just leave a comment if you have additional queries...
---a score of 4 is highly appreciated----- ---if you think this resolution is helpful kindly click on "YES"----
Thank you for choosing fixya
Roger

To remove turn switch, make sure steeing wheel is staight and remove horn button and steering wheel...Now you will need a special tool called LOCK PLATE REMOVAL tool . that will expose the turn swith.Unscrew the turn switch handle and emergency flasher switch.Remove 3 screws to remove the switch.At he bottom of the steering colum is a half-moon shaped connector that you need to disconnect and install a 3 foot piece of wire securelly so when you pull switch out the wire will be able to guide new switch wire into place and reinstall

follow these steps:
1) remove the back case 2) press the power on button 3) remove the battery (button still pressed) 4) insert the battery (button still pressed)

repeat 2-3 times, this will solve the issue...

if it helps plz vote it

follow these steps:
1) remove the back case 2) press the power on button 3) remove the battery (button still pressed) 4) insert the battery (button still pressed)
repeat 2-3 times, this will solve the issue...
if it helps plz vote it

1. Switch off the phone.
2. Hold down the following three buttons: Green (call answer button, * button, and ‘3′ button.
3. While holding these buttons, press the power button and switch on the phone.
4. When the message ‘Formatting’ appears on the screen, release all of the buttons.
Method: 2 ( Hard Format)
1. Switch off the phone.

Programming
When
Key added or replaced. System malfunction.
How
Obtain all keys. A maximum of 3 keys can be programmed. Close all doors and boot/tailgate. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press key lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press key lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press key lock or unlock button. Within 10 seconds: Press lock or unlock button of first key. System should now lock or unlock vehicle. Press lock or unlock button of second key. System should now lock or unlock vehicle. Press lock or unlock button of third key. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed keys.
NOTE: If less than 3 keys are to be programmed, remove ignition key after programming last key.

Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. A maximum of 3 remote controls can be programmed. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press lock or unlock button. Within 10 seconds: Press lock or unlock button of first remote control. System should now lock or unlock vehicle. Press lock or unlock button of second remote control. System should now lock or unlock vehicle. Press lock or unlock button of third remote control. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed remote controls.
NOTE: If less than 3 remote controls are to be programmed, remove ignition key after programming last remote control.

Method:1
1. Switch off the phone.
2. Hold down the following three buttons: Green (call answer button, * button, and ‘3′ button.
3. While holding these buttons, press the power button and switch on the phone.
4. When the message ‘Formatting’ appears on the screen, release all of the buttons.
Method: 2 ( Hard Format)
1. Switch off the phone.
2. Hold down *#7370# button.
3. While holding these buttons, press the power button and switch on the phone.
4. When the message ‘Formatting’ appears on the screen, release all of the buttons.
Method: 3 Soft Reset
1. Switch off the phone.
2. Hold down *#7780# button.
3. While holding these buttons, press the power button and switch on the phone.
4. When the message ‘Formatting’ appears on the screen, release all of the buttons.

1. Disconnect the battery ground cable.
2. Depending on the year and model remove the wiper/washer and fog lamp switch knob if they will interfere with the headlight switch knob removal. Check the switch body (behind dash, see Step 3) for a release button. Press in on the button and remove the knob and shaft assembly. If not equipped with a release button, a hook tool may be necessary for knob removal.
3. Remove the steering column shrouds and cluster panel finish panel if they interfere with the required clearance for working behind the dash.
4. Unscrew the switch mounting nut from the front of the dash. Remove the switch from the back of the dash and disconnect the wiring harness.
5. Install in reverse order.

Good luck.....