Manual for panasonic stereo SA-AK40

Usually there a like five preset buttons...You hold them down like for 5 secs to set. Then just press a button to go back to what you saved

Tuning to radio stations

1. 1 Select TUNER source. ? TUNER is displayed briefly.
2. 2 Press BAND once or more to select your
   waveband.

1. 3 Press down on TUNING a? or a? and release button.
   ? The radio automatically tunes to a station with sufficient reception. Display indication during automatic tuning: SEARCH.? If a FM station is received in stereo, STEREO is shown.
2. 4 Repeat step 3 if necessary until you find the desired station.

To tune to a weak station, press TUNING briefly and repeatedly until you have found optimal reception.


Programming radio stations
You can store up to a total of 40 radio stations in the memory.
Automatic programming
Automatic programming will start with a chosen preset number. From this preset number upwards, former programmed radio stations will be overridden.The system will only programme stations which are not in the memory already.
Press PRESET 3 or 4 (on the remote control ¡ or TM ) to select the preset number where programming should start.
Note:
- If no preset number is selected, default is preset (1) and all your presets will be overridden.
Press PROGRAM for more than 2 seconds to activate programming.? AUTO is displayed and available stations are programmed in order of waveband reception strength: FM followed by MW and LW.The last preset automatically stored will then be played.
Manual programming
Tune to your desired station (see "Tuning to radio stations").
Press PROGRAM to activate programming. ? PROGRAM flashes in the display.
Press PRESET 3 or 4 (on the remote control ¡ or TM ) to allocate a number from 1 to 40 to this station.
Press PROGRAM again to confirm the setting. ? PROGRAM disappears, the preset number and the frequency of the preset station are shown.
Repeat the above four steps to store other stations.

The EUR7711150 remote works for several different Panasonic CD stereo systems. To switch between AM and FM, press the Tuner/Band button. (If you were in another mode, you'll need to press the Tuner/Band button once to get to the Tuner mode and then toggle if needed.) Then if you press Play Mode (above Repeat to the left of the number keys), you can toggle between Preset and Manual. In Preset, the rewind and fast forward buttons select between your preset stations. Alternatively, you can set the presets to numerical values and touch the appropriate number button. (Touch the >=10 button first to access Memories 10-15.) If you are on Manual, the rewind and fast forward buttons will let you move up and down between the frequencies. Pressing and holding Rewind or Fast Forward for a moment will let the radio scan to the next frequency in that direction with a signal.

The CD button enables the CD or MP3 disc player mode. AUX and Tape are for external audio devices and cassette tape mode, respectively.

These comments are based on using the remote with the Panasonic SA-PM19. Please add a comment with the specific model of your Panasonic radio if you need additional assistance.

I hope this helps.

Cindy Wells

There is most likely a short in the amp that needs to be repaired.

Hello
I think that you haven't the operating manual to your Panasonic system. I've the manual to your system, but I can't send it to you by this site, as it does not allow me to upload any files by it. If you send your email address by Fixya comment box, I'll send a copy of it to you by return mail, which have all details you need. OK.

I just dug out the manual and have now programmed a preset.

Instructions:
1) Make sure there are a pair of working AA batteries behind the second (inside) compartment door as these power the memory (mine were Duracells with an expiry of 2001 and had worked all the way through to 2010 before finally failing!)
2) Find the frequency you want with the Up/Down button
3) Press the M button - you will get a flashing M on screen
4) While the M is flashing, press one of the numbered preset buttons.

Manuallly set to the station you want,then pick a preset button & hold down until you hear a beep or 4 about 5 secs

have you tried just holding the preset button down ??

Find the station you want.... press and hold button or your chosing... (1-6) should beep when accepted.

My dear friend the belts of your tape sistem are damaged you need to change him.Good luck