My pgm key won't activate the pgm - Casio TE-2000 Cash Register

Error 01 means that a previous activity has not been completed. Here is a link to the manual: http://totalpos.co.nz/wp-content/uploads/2012/10/Casio-TE2400-Operator.pdf

How do I reset the cash register?

116ER, 117ER, CE2300, CE2350, CE2400, CE280, CE285, CE300, PCR202, PCR204, PCR308, PCR408, PCR350, PCR355, PCR360, PCR365, PCR450, PCR460

This will erase all information - Remove AA batteries and unplug register from wall for 15 minutes.*

If resetting does not work this indicates issue is repair level.

PCRT465, PCR465A, PCRT2000,

This will erase all information - with the PGM key at Off press and hold down the Feed button, while holding the Feed button turn the PGM key down to the PGM mode Release the Feed Button ----INI should appear or a group of 8 zeros

If resetting does not work this indicates issue is repair level.

PCRT470, PCRT480, PCRT48S, PCRT2100, PCRT220S

This will erase all information - with the PGM key at Off press and hold down the Feed (journal) button, while holding the Feed button turn the PGM key down to the PGM mode Release the Feed Button ----INI should appear or a group of 8 zeros, now press one of the below

22500 Subtotal (PCRT40, 480, 48S)

Or

23000 Subtotal (PCRT2100, 220S )

Wait for a receipt to print.

If resetting does not work this indicates issue is repair level.

To program a known frequency into your scanner:
- Power the scanner ON
- Press the E/PGM key
- Enter the number of the channel to be programmed
- Press HOLD
- Enter the frequency, including decimal point
- Press E/PGM to store the data in the scanner's memory

To continue programming, press the up or down arrow to advance to the next channel.

Press HOLD or SCAN to exit the programming mode.

More detailed programming instructions are in the factory operating manual which you can download and print, at no cost, here:
http://www.radiopics.com/1.%20Manuals/Bearcat/Bearcat%20BC340CRS%20%28Manual%29.pdf

For a comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit:
www.RadioReference.com

Bill B.
Listening in since the 60's

To program a known frequency into the BC340CRS:
- Power the scanner ON
- Press the E/PGM key to enter programming mode
- Enter the number of the channel that you wish to program
- Press HOLD
- Enter the frequency, including the decimal point (e.g., 156.225)
- Press E/PGM to enter the frequency into memory

Press the UP or DOWN arrow to advance to the next channel you wish to program

Press HOLD or SCAN to exit the programming mode.

More detailed programming instructions can be found in the factory operating manual which you can download and print, free of charge, here:

http://www.radiopics.com/1.%20Manuals/Bearcat/Bearcat%20BC340CRS%20%28Manual%29.pdf

For a comprehensive database of active frequencies in your area, visit:

www.RadioReference.com

Bill B.
Listening in since the 60's

For a comprehensive database of active frequencies in your area (they're really NOT codes), visit:

www.RadioReference.com

To program known frequencies into your scanner,

1. Press PGM. PGM appears. Then enter the channel number (1-200) where you want to store a frequency, then press PGM again.
2. Use the number keys and DELAY/. to enter the frequency (including the decimal point) you want to store.
3. Press ENT to store the frequency into the channel.
Your scanner automatically rounds the entered frequency down to the closest valid frequency. For example, if you enter a frequency of 151.473, your scanner accepts it as 151.470.

Press DELAY/.if you want the scanner to pause 2 seconds on this channel before it proceeds to the next channel after a transmission ends. The scanner also stores this setting in the channel.

To program the next channel in sequence, press PGM and repeat Steps 2 and 3.

Need the full manual for your scanner? You can download/print it here:

http://support.radioshack.com/support_electronics/doc69/69887.pdf

BillB

First you'll need a list of frequencies to program. For a comprehensive database of active frequencies in your area, visit:

www.RadioReference.com

Once you have your freq list, power the scanner ON,and:

1. Press PGM. Then enter the channel number (1-200) where you want to store a frequency, then press PGM again.
2. Use the keys to enter the frequency (including the decimal point) you want to store.
3. Press ENT to store the frequency into the channel. Press DELAY if you want the scanner to pause 2 seconds on this channel before it proceeds to the next channel after a transmission ends.
4. To program the next channel in sequence, press PGM and
repeat Steps 2 and 3.

Operation
• To listen to a weak or distant station, turn SQUELCH counterclockwise. If reception is poor, turn SQUELCH clockwise to cut out weak transmissions.
• If SQUELCH is adjusted so you always hear a hissing sound, the scanner will not scan or search properly.

Need the full manual for your scanner? You can download/print it here:

http://support.radioshack.com/support_electronics/doc69/69290.pdf

BillB

You might need a special key to program this change, but try this:

1. Turn the key to PGM
2. Enter 9910 . @/FOR CA/AT

If you don't get an error, you're done. Turn back to REG sign on one more time, and try two or more sales in a row.

If you get an error, this kind of programming is disabled in PGM mode. you may have to take it to a Sharp dealer who has a Service key. Your MA (Manager) key can get you to any position marked on the Mode Switch, but the SRV key goes to two more unmarked positions beyond PGM. If you have that key or find a dealer who has, turn it one notch past PGM (to 7 o'clock position).
Enter 910 . @/FOR CA/AT
[Yes, it's a different number than in PGM mode.]

If you ever want to make cashier entry compulsory again, do the same thing, except enter 100 just before touching the CA/AT button.

The reason Sharp doesn't pass SRV keys with its registers is that you can totally mess up your register if you make mistakes with this key. Don't experiment with it, or your only hope may be to wipe all machine memory to get it working again.

move the pgm key to pgm mode 3 subtotal 125 subtotal ( tax table) rate tax and subtotal beginning  level tax ejemplo : for ten cent = 10  and subtotal 5002 subtotal subtotal. 
to applay the tax to dept or plu 
move the pgm key to pgm mode 3 subtotal 366 subtotal 1 and all dept o plu  subtotal 

move the pgm key to pgm mode 3 subtotal 125 subtotal ( tax table) rate tax and subtotal beginning  level tax ejemplo : for ten cent = 10  and subtotal 5002 subtotal subtotal.
to applay the tax to dept or plu
move the pgm key to pgm mode 3 subtotal 366 subtotal 1 and all dept o plu  subtotal

You can only enter PGM mode as manager.(our manager key is #1). The, you are brought to a admin menu.