How do I fix the lcd panel on my aquasmart washing machine?

15.5 Size Setting
If a new motor control module is fitted, the size switch settings will have to be set in the memory.
To size set a L.C.D AquaSmart™ machine:
1. Press and hold the left SCROLL button, then press the HIGH EFFICIENCY button until two
beeps are heard.
2. Press the SCROLL button to select the machine size (600 for WL70, 650 for WL80).
3. Press the POWER button.

javascript:;To size set a L.C.D AquaSmart™ machine:
1. Press and hold the left
SCROLL
button, then press the
HIGH EFFICIENCY
button until two
beeps are heard.
2. Press the
SCROLL
button to select the machine size (600 for WL70, 650 for WL80).
3. Press the
POWER
button

A reconditioned motor controller board is cheaper than a new one.
First six digits under the bar code on the yellow label
is the part number for the motor controller board
The Pump you will have to buy new. Sorry

these are a common problem for AquaSmart machines.
Your AquaSmart machine requires 4 new suspension damper rods & 4 top bands,

You need to size set the LCD panel to your motor controller.
1. Press and hold the left SCROLL button,Then press HIGH EFFICIENCY button until two beeps are heard.
2. Press the SCROLL button to select machine size
(600 for WL70,650 for WL80).
3. Press the POWER button to set in memory.

shouls not make any diffrence but i dont know you original question ?

maybe it could be the board is not crrectly in place so look at that first

Hi and welcome to FixYa. I am Kelly.

You did not provide a make and model number so here is my best model to problem guess....

Your new control board is missing the size information.

AQUASMART-SIZE-SETTING. Size information must be programmed when a Motor Control Module or Display Module has been replaced. If the size is not set, the display will show fault code 9, or the water levels and wash actions will be incorrect. If the machine displays fault code 9, the machine must be switched off at the wall and then back on again before it can be sized.

Setting the size:

Unplug at the wall and then re-plug it in.

Press and hold Temp Up, then press Power. Wait for the 4 beeps, then set your machine size as follows to YOUR machine size:

5/5.5kg machines - press Temp Up. Cold led should light.
6/6.5kg machines - press Water Up. Low water led should light.
7/7.5kg machines - press Spin Speed up. Spin hold led should light.

Power off, try a programme.
Thanks for using FixYa!

_____________________________________


From the Tech Sheet:

IWL12 and GWL 11 are different models. One of the two procedures will work for your machine.

The machine size must be set into the machine
memory if a Motor Controller or Display Module has
been changed.

To set the size:
1. Turn the power on at the power point and off
at the console.

2. IWL12 - Press and hold the FABRIC CARE
button, then press the POWER button. This
will present a set of options in the LCD
screen. The LCD screen has within it a
number of options. Push the Adjust button to
highlight the 650mm (L) machine size.
Pushing the POWER button will lock the size
into the module’s memory.

GWL11 – Press and hold the WASH TEMP
UP button then press the POWER button.
Press the SPIN SPEED UP button (the HOLD
LED should be on.)
3. Press the POWER button to return to normal
operation.

Kelly

Tom,
I don’t believe you will find a schematic for the control board. I have a FAV6800AW all I have be able to find is the wiring schematic found in the FAV6800AW/FAV9800AW Service Manual.
Is your machine out of the 5yr warranty period for the Control Board? I got Maytag to send me one.
Saw this on e-bay
NEW - Maytag Washer LCD Control # 25001189
Good luck … Rich

Error 245: SmartPump Stall
Pump Impeller is jammed cannot turn.