How to reset Edimax BR-6204Wg router? default wireless password?

You will have to reset the router.
Step 1 : Power on the router.
Step 2 : Locate the hole below the word Reset on the rear panel of the
router
Step 3 : Press and hold the Reset button for about 10 seconds using a
paper clip or pen and then release.
Step 4 : After about 1.5 minutes, The router will then reboot itself and
return its default password, "1234".

IT NEED SOME SERVICE

It will have to be reset to factory defaults, and then re-configured

http://www.edimax.com/images/Image/FAQ/Router/General-Router/ForgetPassword-Router.pdf

Here is a quick install guide:


http://www.edimax.co.uk/images/Image/QIG/Wireless/BR-6204Wg/BR-6204Wg_QIG_English.pdf


Hope this helps you.

Reset everything including the Hard reset (a small probably hidden button you must press for 15 seconds) you will find somewhere on the wireless router. I trust your laptop is capable of connecting wirelessly???and you have done this before???

Try this link its your router's manual from its manufacturer's site. Drop down page then click manual it will download your manual. Then read from resetting the router and default user and password.

http://www.edimax.com/en/produce_detail.php?pd_id=11&pl1_id=1&pl2_id=2#03

Be aware that by doing the reset the router will be back from default settings.

Goodluck.

The default settings for your router are : 192.168.2.1 User name :admin and the Password is : 1234

The deal is that you can access that site only with the router identified by your connect. If you're trying to login from a different connection, it doesn't match the IP address. And it automatically locks it.
When the connection problem was resolved, the password and username worked.

Try reading the Quick Installationguide and see of that helps.
 
http://www.edimax.com/images/Image/QIG/Wireless/BR-6204Wg/BR-XXXX_QIG.zip

I believe I can help.

As I understand you use your Siemens to get to Internet and you like to use another Edimax 6204 WL Router on another floor.

You don't have to change much !

First check if DHCP on your Siemens Router is ENABLED (it should be) !

- RESET your EDIMAX Router (to be sure everything is set by default)
and disconnect any LAN cables from it.
- If you are using Laptop (or desktop with WL adapter), connect it to your EDIMAX by LAN cable.

- Set (if it is not) LAN adapter IP and DNS of your Laptop/Desktop
to 'Obtain an IP address automatically'
If it was seto to some STATIC IP, after this you may need to 'REPAIR' your LAN connection
to get a new IP from your Edimax router

- Open your browser and type http://192.168.2.1
(admin + pass: 1234)

- Go to Wan port and check it. It should be set to Dynamic IP.

- Go to LAN settings and type IP address of the Edimax Router in the same Class
as Siemens Router is. (e.g. if Siemes router is 192.168.1.1 then Edimax should be 192.168.1.2)

- Change the DHCP range too, but be carefull this range should be different from DHCP range on your
Siemens router. (e.g. if Siemens router range is 192.168.1.100 to 192.168.1.200, then you should
set Edimax DHCP range from 192.168.1.201 to 192.168.1.250)

- Now, connect the LAN cable from one of Siemens LAN port to WAN port of your Edimax.

That's it!

Now you may change SSID, Security, Time etc. on your Edimax router, and also try to connect via your Laptop's WL adapter. (also make sure it has no static IP address)

Hope this helped.