Displaying PLEASE WAIT STARTING SYSTEM.how do i know the right OACB firmware do boot the machine and how do i save the firmware in the USB memory stick?

I found this
https://www.google.com/search?q=canon+ir2016j+firmware+download

iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
This machine and options can be upgraded by downloading system software programs from the personal computer (hereafter called as the PC) in which a service
support tool (hereafter called SST) has been loaded.

System software programs and upgrade tools are listed in the following table:

SST =Main unit System (main controller) The main controller also controls the reader.
Boot = (boot program)
Option PCL = (PCL printer kit-J1)
Fin_U1 (Finisher-U1) Dedicated service tool needed to update (Downloader PCB: FY9-2034)

Firmware.jpg

iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i

System software programs to be downloaded need to be registered in the SST.
The system software programs are registered with the names listed below.
<Software Programs Pre-Installed in Main Unit>
Machine name:iR2020
Unit name:
- Main controller: System
- Boot program: Boot
- PCL board: PCL

[System Software Registration Procedure]
Start the PC.
Start SST.
Click the "Register Firmware" button.
Select the drive in which the system was downloaded
Then click the "SEARCH" button.


A list of system software programs contained is displayed.

This machine does not allow two or more system software programs to be downloaded at the same time. If two or more software programs need to be upgraded,
register and download them one by one.

When the system software program registration result appears, click the OK button.

Connection
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
1) Turn off the main power switch of this machine, and then disconnect the cables connected to this machine.
2) Connect USB connector on the back of this machine to the PC using the USB cable
Downloading Procedure
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
1) Turn on the power switch of the PC and start SST.
2) When the power switch is turned on, the Found New hardware Wizard appears. Click "Cancel".
3) Select "MFP" in "Target Selection", and then select "iR2020" in "Model List".
4) Double-click the "System" folder in "Model List" to check the system software version. Select "USB" in "Interface", and then click the "START" button.
5) Turn on the power switch of the host machine.
6) Press the following keys on the control panel to enter the service mode.
Additional Functions Key > 2 Key > 8 Key > Additional Functions Key
7) Using the plus (+) or minus (-) key, select "#DOWNLOAD".
8) Press the OK key on the control panel to place the host machine in the downloading wait mode ("#DOWNLOAD CONNECTED" is displayed).
9) Press the OK button on the SST screen displayed on the display of the PC.
10) When connection is complete, Click the OK button in SST MENU.

Scanner image
processing board
(SCIPB)
• Memory control board /1
(MCB1)
• Overall control board
(OACB)
• Printer control board
(PRCB)


any one of the above boards$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ have tech come reflash the firmware first

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Step 1:
There are many good reasons for booting your computer from a USB drive. For instance, if you want to try out another operating system without disturbing the main hard drive on your computer, then installing the new OS on an external drive is a great way to run the system through its paces and decide whether you like it.

This approach will offer you the flexibility of being able to run both operating systems on your computer. However, before you can boot the new operating system from the USB drive, you will need to change the boot order for your computer in the system BIOS.

Connect the external USB drive or pen drive to the computer before you power it on. Press the "Delete" key as the computer performs the "Power On Self Test" (POST) to enter the BIOS area of the computer firmware. The POST performs a diagnostic of components on the motherboard and does a cursory check of the hard drive, memory and processor. The POST only lasts a few seconds; therefore, press the "Delete" key quickly. Enter the administrative BIOS password if prompted to do so. Once you enter the correct password, you will see the main BIOS screen. Use the right-arrow key to navigate to the "BOOT" menu option at the top of the screen, and press the "Enter" key. Press the down-arrow key until the cursor is on the "Boot Device Priority" label. Hit "Enter," and press the down-arrow key again to highlight the "1st Boot Device" option. Press the "+" or "-" keys to scroll through the available boot options until the "USB Drive" or "USB-HDD0" label is the highlighted option. Press the "F10" key to save changes and exit the BIOS setup program. When the computer restarts, wait for the "press any key to boot from external drive" prompt to display, and then press any key on the keyboard to boot from the USB drive. Award or Phoenix BIOS Connect the USB drive to the computer. Wait for the POST to display on the screen, and press the "Delete" key to enter the BIOS. Enter the BIOS password if prompted to do so. Tap the right-arrow key until the cursor is over the "BOOT" menu option. Press the "Enter" key. Press the down-arrow key until the highlighted cursor is on the "Removable Devices" option. Press the "+" key until the "Removable Devices" label is on the top of the boot device list. Press the "F10" key to save the changes for the boot order in the BIOS and to exit the utility. After the computer restarts, press any key on the keyboard to boot from the USB drive when prompted to do so.

How to recover system files on H10?1.2. LCD on H10 displays "USB Connected" and then double click "My computer".
3. Click right mouse on "H10" drive and select "Properties"
4. Go to Tools -> Error checking -> Check Now -> Check "Automatically fix file system errors" and click start.
5. It will take you around 1~2 minutes, 5 minutes at maximum.
6. Go to "Tools -> Folder Options -> View" on Windows Explorer. Uncheck "Hide protected operating system files(recommended)". Click OK to save properties.
7. Double click on "H10 drive" and delete "System" folder.

8. Open iriverplus and transfer music.

If your device was detecting by USB cable. Then update the firmware for this device:
1. Please open iriverplus3 and connect your device with USB cable.
2. After connecting your device, please follow the steps below to upgrade New Firmware
** Tools -> Portable Device -> Firmware Upgrade **
3. After upgrading the New Firmware, please check the firmware version before playing device.
** Setting -> Advanced -> System information **

Hope this will resolve the issue.

Regards
Nandu

All you have to do is

Step One
To save data, use EASEUS Data Recovery software (free version - 1GB of data recovery). how:
1. Download and install EASEUS Data Recovery
2. Insert micro SD
3. Open EASEUS Data Recovery, choose Complete Recovery - Next
4. Select the drive micro SD - Next
5. Save the data to the hard disk (max. 1GB)
6. Because of your micro SD 2GB, repeat the process of recovery (repeat step 2, 3, 4, 5)
After all data is secure, do the process repair micro SD

Step Two
The first alternative - use the software HP Drive Key Boot Utility

Using the HP Drive Key Boot Utility, for Win XP
1. Download and install the software HP Drive Key Boot Utility
2. Then, double click the file cp006049.exe - select Install.



3. Insert micro SD
4. Then, open the program "HP Drive Key Boot Utility" - Next - select drive - Next - Create new or replace exiting configuration - Next - Hard drive - Next - Create new file system - Next - wait until the process is completed - Next - Create firmware flash package - Next - Finish.
5. Remove the micro SD from the USB port, then insert it again.
6. Quick format micro SD (FAT file system)
7. Restore all data, to the micro SD.

Using the HP Drive Key Boot Utility, for Win Vista or Seven
1. Download and install the software HP Drive Key Boot Utility
2. Then, double click the file cp006049.exe - select Extract



3. Insert micro SD
4. Then, double click file hpdkbu.exe - Next - select drive - Next - Create new or replace exiting configuration - Next - Hard drive - Next - Create new file system - Next - wait until the process is completed - Next - Create firmware flash package - Next - Finish.
5. Remove the micro SD from the USB port, then insert it again.
6. Quick format micro SD (FAT file system)
7. Restore all data, to the micro SD.


The second alternative - use software HDD Low Level Format Tool
1. Download and install HDD Low Level Format Tool
2. Insert micro SD
3. Open program HDD Low Level Format Tool, select micro SD - continue
4. Click S.M.A.R.T - click Get Smart Attributes
5. Click LOW LEVEL FORMAT - click Format this device
6. Wait until the process is complete - press OK
7. Remove the micro SD from the USB port, then insert it again.
8. Quick format micro SD (FAT file system)
9. Restore all data, to the micro SD.

I hope this information helps.

Hello 3G,

To resolve the issue Error e225,

Turn the main power switch off and then back on-ICMF 4000 series/D400 Series

or

Update the firmware :

There is a risk that the MF4150 will not operate if power interruption occurs
during the firmware update. Please make sure MF4150 is connected to
reliable AC power source.

1. Save the downloaded file "MF4150_FirmwareUpdateTool_V0xx.exe on local drive. (i.e. desktop)
Computer Requirements for update
- Microsoft Windows 2000 or XP (32bit)
- Equipped with a USB port (either 1.1 or 2.0)
- Free disk space: 100 MB or more
2. Make sure that Processing/Data indicator (Green LED) on the MF4150's operation panel is turned off.
If the light is lit or blinking, wait until all the jobs are finished (i.e., COPY, PRINT, and SCAN), and that the Processing/Data indicator is turned off.
3. Make sure that Error indicator (Red LED) on the operation panel is turned off. If Processing/Data indicator (Green LED) is lit and Error indicator (Red LED) is blinking at the same time, jobs are held in the printer memory due to an error, possible cause is out of toner or paper has run out, or toner cartridge is not installed. Check the LCD for and error message and refer to the documentation that came with the printer to resolve the error.
4. Disconnect Fax line cable from the MF4150 to prevent Fax reception interruption during firmware update.
5. Make sure the USB cable is directly connected to the MF4150 and your computer.

• Do NOT use a USB hub to connect the cable, as it may lead to a connection error.
• Make sure the machine is not in the Sleep mode (i.e., [Energy Saver] key on the operation panel is leit). To exit the Sleep mode, press [Energy Saver] and confirm that the Energy Saver light is off.
• You need to log on as an administrator to perform this update.
• Make sure that no other applications are running on your computer.

6. If [Found New Hardware Wizard] appears on your PC screen, click [Cancel] to exit the screen.

• [Found New Hardware Wizard] screen may be displayed multiple times. Cancel anytime you encounter this screen while performing this update.

7. Double-click ?MF4150_FirmwareUpdateTool_V0xx.exe? that you downloaded and saved.
8. Double-click "MF4150_V0xx_FirmwareUST.exe" that is in the newly created folder as a result of uncompressed downloaded file.
9. Confirm that the machine is in the ready status, and then click [Transfer]

• If the printer is not detected: Check if the printer's power is turned on and the USB cable is properly connected. Then click [Retry] to proceed.

10. The firmware is transferred to the printer.

• Never turn of the power to the MF4150 while firmware is updating. If power interruption occurs while the firmware is being updated the control board will be damaged and will need to be replaced. The replacement of the control board and labor will not be covered under warranty.
• If an error occurs while transferring the firmware: Check if USB cable is properly connected. Click [Retry] to proceed.

11. When [Firmware transfer is complete] appears, click [Exit].
The printer starts the update process automatically.
<ERASE FLASH ROM> appears on the printer's display while the existing firmware is being erased.
Then printer's display shows <FIRMWARE UPDATE> while updating the firmware.
When the firmware update is complete, the printer's display shows <FIRMWARE UPDATE OK> <MACHINE POWER OFF/ON>
12. Turn printer's power switch OFF, wait 2 seconds then turn the power switch back ON. Check that there is no error on the printer display. Reconnect removed fax line cable.

Make sure you read this all before starting anything and if this helps please leave me a rating, if not let me know and I will try to help you farther.
Thank You
ETRONIC

Symptoms:
On start, PS3 Green light comes up but nothing happens. No sound or video
Insert game or any disc into the slot, blue blinks and again nothing happens
Try to assign wireless controller, nothing happens.
Try restart the console, unplug it for a while, or keep it on for long time again does not solve the problem.
Solution:
With the PS3 in Standby mode (Red light on), press and hold the Start button until you hear a single beep, followed by double beeps.
Connect the controller using USB cable and press the PS button on the controller.
Now, the system restore screen (or whatever they call it) will come up like the Picture at the bottom of this writing.

You have several options here for restoring the system, some will unfortunately wipe up all your data, others will make you lose the file naming. For me, I tried the option top-bottom and eventually had to do the Restore PS3 System. Luckily, all I had were demos, trailers, and game saves. only game I was really playing now was Prince of Persia. I felt terrible still though, but much better than if I was playing Ninja Gaiden or MGS right? Or let’s say a game Fallout!
-----------------------------------------------------------------------------------------------------------------
"I have found a way to keep all your saved data with this problem.
Follow the steps above but first download the latest firmware update from the playstation website and save it onto a USB key. Follow the steps and choose the bottom option "SYSTEM UPDATE". Wait for it to update and it should restart with all your music, videos and gamesaves."

You can save the scanned data on a USB memory or a memory card by using the control panel.

IMPORTANT

- You can not use USB memory card and memory card simultaneously.

1 .Select Scan (Scan) on page HOME (HOME) and then press the OK button.

The screen where you select where the data should be saved is displayed.

2 .Turn the USB memory card direct print port or memory card into the slot.

3 .Select USB flash drive (USB flash drive) or memory card (Memory card) and then press the OK button.

4 .Select Save on USB disk (Save to USB flash). The screenshot Scan documents (Scan document) is displayed.

5. State the necessary settings and then press the OK button.

6. Place the original on the glass plate as shown on the LCD screen.

7. Press the [color] (Color) for scanning in color, or button [Black] (Black) for scanning in black and white.

When the preview is enabled, press the OK button after viewing the preview pane on the LCD screen.

The machine starts scanning and the scanned data is stored either on the USB memory card. Remove the original from the glass plate, the scan is complete.

REFERENCE

- You can only scan images continuously when you select PDF. Continue to scan the confirmation screen. You can save up to 100 pages of images in a PDF file.

- If the USB memory card or memory card becomes full while images are scanned, saved only images that are already scanned.

- You can save up to 2000 files of scanned data in both JPEG and PDF formats.

- Folder and filename of the scanned data stored on USB memory or memory card is as follows:

• Folder Name: (extensions: PDF): CANON_SC \ DOCUMENT \ 0001

• Folder Name: (File Extension: JPG): CANON_SC \ IMAGE \ 0001

• Filename: Serial number, starting from "SCN_0001"

• File dates: 01/01/2008

It is under the Administrator Menu:

From an Idle state, Press:

Menu

Next - you should see "configuration administration" on the display.

Press the left or right arrow key until "Administration Startup Options" is displayed.

Press "select"

Press the left or right arrow key until "do start page" is displayed.

Press select.

Press the left or right arrow until "no" is displayed.

Press "online" (save changes *no? should be displayed)

Press "next" (right arrow) "save changes? yes" should be displayed.

Press "select" to save settings.

Press the select to reboot the system.

This came directly from the operators manual, and may differ depending on the firmware version of your machine. If this does not work, please let me know and I will research it further.

Hai

I understand that your Isue is "After installing the HP All-in-One software, the computer stops responding during start up when the All-in-One is connected and turned on. The computer will start correctly if the All-in-One is not connected or is turned off."

SOLUTION:

This problem can be resolved by changing the "USB Emulation" in the Computer BIOS settings.
If you are using a DELL Computer just follow my instruction below.

Caution:
If you are using a USB keyboard, do not disable “USB Emulation”, “USB Keyboard Support”, or “USB Legacy Support”. If the settings must be disabled, use a PS/2 keyboard

Changing the BIOS on a Dell Dimension computer
Follow the steps below to turn off the ability to boot from USB devices but still support a USB keyboard while starting. Contact Dell for assistance if necessary.

1. Shut down the computer.
2. Unplug all USB devices other than a keyboard.
3. Start the computer. When the Dell logo displays, press the F2 key to enter the System Setup (BIOS) program. If the Windows screen displays, wait for the computer to finish starting up, shut it down, and then try again.
4. Press the Down Arrow key to highlight Integrated Devices (Legacy Select Options).
5. Press the Enter key.
6. Press the Down Arrow key to highlight USB Emulation .
7. Press the Space Bar until the “ No BOOT ” option displays.
8. Press the Esc key twice to go to the Exit menu.
9. Plug the USB devices back in.
10. Ensure that “ Save Changes and Exit ” is highlighted, and press the Enter key. Contact Dell for assistance if the problem still exists

Changing the BIOS on a Dell Laptop PC.
Follow the steps below to turn off the ability to boot from USB devices but still support a USB keyboard while starting. Contact Dell for assistance if necessary.

1. Shut down the portable.
2. Unplug all USB devices including USB keyboards.
3. Start the laptop. When the Dell logo displays, press the F2 key to enter the System Setup (BIOS) program. If the Windows screen displays, wait for the computer to finish starting up, shut it down, and then try again.
4. Press and hold the ALT key while tapping the P key until a screen displays that includes the words “ USB Emulation ”.
5. Press the Down Arrow key to highlight “USB Emulation”.
6. Press the Right Arrow key until the “Disabled” option displays.
7. Press the Esc key once to go to the Exit menu.
8. Plug the USB devices back in.
9. Ensure that “Save Changes and Exit” is highlighted, and press the Enter key. Contact Dell for assistance if the problem still exists

Change the BIOS on computers from manufacturers other than Dell If you do not have a Dell computer, contact the computer manufacturer for assistance. If the manufacturer does not know how to disable starting from USB devices, they may be able to change the order (boot order) of the disks the BIOS uses to start the computer. Move the bootable USB devices selection lower on the list than the computer hard disk drive. If you have any further queries or if the problem still persists, reply me. Thanks Riz ([email protected])