Front load washer LG wm2140cw with error code up side down FE. Any ideas what this means? Will start to run then error code shows up and it stops.

Here is the LG site for washing machine error codes, you can scroll down and find the FE code there:
http://www.lg.com/us/support/product-help/CT10000010-20150140270078-other-error-codes

The site shows the following:

The FE error code indicates the washer is overfilling. This is usually the result of a faulty water valve.

1. Close both water taps.

2. In order to drain out any trapped water, power the washer back on and press the Spin Speed button until No Spin is selected and press the Start/Pause button.

3. Once the washer has drained, restart the wash cycle.

This fe error or fault code indicates that the washer is overfilling due to a defective water inlet valve. The valve is not repairable and will need to be replaced.

I found this information on the internet. I hope that it helps.
" Getting fe code on lg washer.
"This means that the washer is overflowing. This is a built in fault that turns on the drain pump so that the water doesn't get so high that it gets into the floor. If water is continually flowing into the washer you will get this problem. If this is the case the water valve is most likely the problem. To confirm unplug the washer and if the water doesn't stop flowing into the washer the water valve is the problem.

Thank you,
Shawn"

I hope that this helps you out

FE = Fill Error. Not a faulty water valve in your case. (FE codes if it takes too long to fill the machine, but if the water is leaking out, the valve is not the problem, the leak is) If you take the back cover off, you might be able to see where the water is comming from. Possibly the black rubber hose from the tub to the pump has a leak.

Hi dear.OE code meaning on Lg washer's"machine unable to drain in 10minutes". You can make a little test.Please remove the filter & pour some water in side drum ,watch for water coming out of filter.If it's slow, tub to pump hose clogged.(there must be some sort of fluff or coin clogging hose)if it's not slow,waters comes out freely, run machine on drain cycle & check the pump motor is it running smoothly?If not change the pump.I hope that helps.Thanks.

Hello,
Here are the common error codes for the LG machines.

LG Washing Machine Error or Fault Codes

If you have a LG Washing Machine you may see an error code come up and wonder what it is. Here are the common error or fault codes that will be displayed on the LG machine.

OE

This means that the washer has tried for ten minutes to drain the water out of your machine and the water did not drain out.

UE

This means that the load in the drum is out of balance causing excessive vibration when spinning.

IE

This means that the washer has not filled with water in 8 minutes.

LE

This means that the motor and the control panel are not talking to each other properly

PF

Power Failure – The power has gone out to the machine and then has come back on

FE

This means that there is too much water in the machine

PE

This means that the water level sensor is not working properly

CE

The washer motor has received and over current condition

TE

This means that your heating sensor is not working properly

SE

This means that you had a temporary sensor error

HE

This means that you had a temporary heater problem

DHE

This means that you had a temporary dry heater problem

This will give you a basic idea of what has caused your error code.


Heatman101

From the manual ,FE means Water level is too high due to a faulty water valve. hence the possible leak

EU --- error means ---Unbalanced load is sensed three times during a spin operation. to resolve the issue ----Open lid. Rebalance laundry load and close lid.· Check wiring harness
· Check unbalance switch
· Check circuit board

my lg senseclean wash mashine shows the sign Cl on the display and the door cannot be open what does it mean?