Question about HP Photosmart D7160 InkJet Printer

Open Question

It keeps saying :" No more paper, charge paper in the tray...then press OK" and i have done that many times w/o success. I have also try to shut down the printer and reopen it and it keeps saying the samr thing...???

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Wafik
  • 16 Answers

SOURCE: printer doesn't recognize paper

if u remove papaer from feeder u should c the paper sensor this sensor is located deep inside the printer try to move it (mayb stuck) with a screw or any thing tall then try to aprint again this sensor is responsible for detecting the presence of paper

Posted on Nov 28, 2007

Ad
  • 1 Answer

SOURCE: hp photosmart d7160

hp photosmart d7160

how can i print 4x6 photo paper ? it says load paper in the main tray its only printing with large plain paper , even if its set to photo tray , and if i put the 4x6 in the main tray it says wrong paper zize ...

Posted on Dec 13, 2007

  • 1 Answer

SOURCE: When I turn on my printer I get the message Error Press OK

You have to refit the micropump gear, this is happening because this gear should be out of its place. It's on the left side of your printer. I.ve just solved the same problem.

Posted on Nov 27, 2008

  • 1 Answer

SOURCE: printer will not start

This is likely a hardware problem. However you can try a sem-full reset to factory default conditions by 1. unplugging the power cord while the printer is powered on and 2. press and hold the OK and Cancel buttons while plugging in the power cord. If this this does not clear the error you probably have a hardware issue. On my printer, after going through a diagnostic procedure with the HP Chat Tech and concluding a hardware issue I did a bit more research and then took the printer apart. It turns out that a fairly common problem is for the large white gear on the left side of the printer that drives the ink pump comes off the shaft. I reassembled it to the shaft and put the printer back together. When I plugged in the power cord the printer started and did about a 5 minute maintenance procedure and now works fine.

Posted on Jan 29, 2009

  • 1 Answer

SOURCE: Tray which printer prints from.

Just had this problem and stumbled upon how to fix it. Check the guides in your tray 2. Our back guide was slightly off of the proper spot for letter size paper. This was causing the printer to think the tray had a custom size of paper in it. Your document is probably trying to print on letter size paper and when it doesn't think the paper is in there it switches to tray 1.

Posted on May 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I have a Dell printer, and it says "MPF Load Error" every time I try to print something. How do I fix this?


Verify the Paper Type Matches the Type Set in the Printer´s Operator Panel

To verify the paper type matches the type set in the printer's operator panel, perform the following steps:
  1. Press the MENU button.

  2. Press the down arrow until Tray Settings appears and press the return%20arrow%203100cn.jpg button.

  3. Press the down arrow until Paper Type appears and press the return%20arrow%203100cn.jpg button.

  4. Press the down arrow until the specific paper tray (Tray 1, Tray 2, or Multipurpose Feeder) appears and press the return%20arrow%203100cn.jpg button.

  5. Press the down arrow to select the specific paper type, as shown in Table 1, and press the return%20arrow%203100cn.jpg button.

  6. Press the MENU button.

Print from the Multipurpose Feeder (MPF)

To print from the Multipurpose Feeder (MPF), perform the following steps:
  1. Click the Start button, point to Programs, point to Accessories, and click Notepad.

  2. Type the word test.

  3. Click File and then click Print.

  4. In the Print window, verify that the Dell 3000cn / Dell 3010cn / Dell 3100cn printer is selected in the Select Printer dialog box.

  5. Click the Preferences button.

  6. In the Printing Preferences window, click the Paper Tray tab.

  7. Click the Paper Source drop-down and select MPF.

  8. Click OK.

  9. Click Print.


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Aug 19, 2011 | Dell 3010cn Laser Printer

1 Answer

Not printing black


To align the printer from the control panel

1. Load letter, A4, or legal unused plain white paper into the input tray.
2. Press Setup.
The Setup menu appears.
3. Press to highlight Tools, and press OK.
The Tools menu appears.
4. Press to highlight Align Printer, and press OK.
5. The HP All-in-One prints a test page, aligns the print head, and calibrates the printer.

Recycle or discard the page.

A success or failure message appears.

Note If you have colored paper loaded in the input tray when you align the printer, the alignment will fail. Load unused plain white paper into the input tray, and then try the alignment again.If the alignment fails again, you might have a defective sensor or ink
cartridge.

6. Press OK to continue.
7. Recycle or discard the page.

Oct 13, 2009 | HP Photosmart C7280 Laser Printer

1 Answer

Konica Minolta c451: Tray 1 is not available


look behind the tray for paper....
if not do the folowning
power machine off from main switch sould be on the side or open the front door it;s on bottom left side.hold down the utility botton while powering on keep holdin untel prompted with message ...TROUBLE RESET press it should say ok than powr machine off wait 20sec power back on
hope that help
keep us posted

Mar 06, 2009 | Konica Minolta Office Equipment & Supplies

1 Answer

HP C5250 All in one says "out of paper"


Try to do the following reset on the machine: disconnect the power cable from thr back of the all in one, than press and hold the button ok and help together while reconnecting the power cable. Release the buttons when machine shuts down automatically. Reboot the machine. Reset is done.

Jan 26, 2009 | HP Office Equipment & Supplies

1 Answer

Printer won't print properly.


Hi,


Please perform the following steps:

  1. Load unused plain white letter or A4 paper into the input tray.
  2. Press the Setup button.
  3. Press the down arrow button to select Tools and then press OK .
  4. Press the down arrow to select Align Print Cartridges and then press OK . An alignment page prints.
  5. After the success or failure message displays, click OK to continue. Recycle or discard the alignment page.


Regards,

Sagarjd

Nov 08, 2008 | HP Photosmart C4180 All-In-One InkJet...

1 Answer

Would not print C5280 Flashing Failure Print Cartridge allignment


Solution
  1. Load unused plain white letter or A4 paper into the input tray.
  2. Press the Setup button.
  3. Press the down arrow button to select Tools and then press OK .
  4. Press the down arrow to select Align Printer and then press OK . The unit prints a test page, aligns the printhead, and calibrates the printer.
  5. After the success or failure message displays, click OK to continue. Recycle or discard the alignment page.
Cause An incorrect type of paper is loaded in the input tray. If you have color or photo paper loaded in the input tray when you align the printer, the alignment might fail.

Nov 04, 2008 | HP Office Equipment & Supplies

2 Answers

3010 dell color laser


Ok,

I've went around and around with the same problem (bug) and finally found a solution. Here is the deal. You have to exactly match the settings for the MPF tray in the aplication softwares to the MPF tray settings set from front panel on the printer.

I found this problem when trying to print on gloss paper. The MPF tray had to be set for "Coated 1 Side 2" in both the application and on the front of the printer.

Lets say I'm printing a Word Document. Go to file, print, select the Dell printer, then select properties, select paper tray, set paper source to MPF, set MPF settings to ""Coated 1 Side 2". Click OK.

Now do the printer setup. From the front panel on the printer.
Press Menu, press the down button to Tray Settings
Press center button to select.
Display now asks for paper type. Press center button.
Displays MPF. Press center button.
Push down button until you see Coat1 Side2
Push center button to select.
Press Menu to exit.

I only print on gloss so I have to set the MPF tray to Coated 1 Side 2. I was told this slows the feed and that is needed for coated papers. Now you could probably use another setting as long you set both the MPF tray in both the application and the control panel to match exactly.

Aug 19, 2008 | Dell 3000cn Color Laser Printer

2 Answers

Out of paper problem


maybe you might consider scanning the picture, saving it, and then printing from another application?

Apr 28, 2008 | HP Photosmart C4150 All-In-One InkJet...

Not finding what you are looking for?
HP Photosmart D7160 InkJet Printer Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...