When i press the power key ,get a lock signal

Does your fusion have Power Door Locks - Without Memory or Power Door Locks - With Memory ? Do you know about ford SJB - smart junction box ?

Power Door Locks - Without Memory
Regardless of the key position, the smart junction box (SJB) is supplied voltage at all times. When the SJB receives a signal from the remote keyless entry (RKE) transmitter, the keyless entry keypad, or the door lock control switches, the SJB supplies a ground signal to the appropriate lock or unlock relay. The ground signal closes the relay which supplies voltage to the door lock actuators. The door lock actuators then actuate to a lock or unlock position.
Power Door Locks - With Memory
Regardless of the key position, the SJB and the driver door module (DDM) are supplied voltage at all times. When the SJB receives a signal from the RKE transmitter, the keyless entry keypad, or either door lock control switch, the SJB sends a command to the DDM, through the controller area network (CAN), and a ground signal to the lock and unlock relays. When the LH door lock control switch is pressed, the DDM receives the lock or unlock signal. The DDM will send a request through the CAN network to the SJB to lock or unlock the passenger doors. The SJB then responds to the DDM request, authorizing a lock or unlock of the driver door by the DDM. The DDM then supplies voltage and ground to the driver door lock actuator based on the lock or unlock request. The ground signal in the SJB closes the relay which supplies voltage to the remaining door lock actuators. The remaining door lock actuators then actuate to a lock or unlock position determined by the relay.

• A single or all passenger door locks are inoperative - with memory

• Circuitry
• Door lock actuator (part of the door latch)
• DDM
• SJB

• Go To Pinpoint Test A .

• A single or all passenger door locks are inoperative - without memory

• Circuitry
• Door lock actuator (part of the door latch)
• SJB

• Go To Pinpoint Test B .

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Unlock procedure and to override the password lock to many popular brand TVs are given.

You might have a bad ignition switch. Do the other accessory power features stay on too? Eg .... Radio, blower fan... Do the turn signals still operate when key is removed? But a bad multifunction switch (turn signal, headlight switch) coukd also be bad.

Press the Power key& Volume - key at the front panel of the TV simultaneously. For most Technica brand TVs, will be unlocked by this procedure. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy.
http://electronicshelponline.blogspot.com/
Unlock procedure to most popular brand TVs are given by one post.

First check the num lock status on key board after power up the computer press num lock key then check the num lock led status if it is on and off when you press num lock then cpu is working fine only issue with screen resolution for that when you power up the computer press F8 key 5 to 6 times untill you can see safe mode and other menu enter in "enable vgamode " then if you are able to enter then go to display property and change screen resolution to 1024*768 then apply and check.but if you are not able to enter then open cpu cabinet cover then reconnect RAM memory pull cmos cell from motherboard for 10 minutes then put it back also try with another RAM memory make sure motherboard is not ground with cabinet cover.Let me know if you need further assistance.Thanks for using FixYa.

iPhone setting:*
- Auto-Lock: 1 Minute;*
- Passcode Lock: On, require passcode immediately, after 15 min or 4 hours etc;*
- Network: Turn 3G Off

Scenario 1: Home screen is active with screen on*
1. Press power button for seconds until asked to '"slide to power off"
2. Slide to power off
3. press power button to turn on iPhone
4.*When asked to enter passcode, touch the "Cancel" key, then slide to unlock
5. bypassed passcode

Scenario 2:*
1. On the screen of being asked to enter passcode, press power button for seconds until asked to '"slide to power off"
2.*Slide to power off
3. press power button to turn on iPhone
4.*When asked to enter passcode, DO NOT touch any key on the screen, press power button for seconds until asked to '"slide to power off"
5. Slide to power off
6. press power button to turn on iPhone
7.*When asked to enter passcode, touch the "Cancel" key on the right bottom corner, then slide to unlock
8. bypassed passcode

Notes:
1. When Network setting changes to Enable 3G: ON, "3G" signal shows up, passcode CANNOT be passed through
Go to a underground parking lot or a lift where 3G signal is weak, when 3G signal switches to "E" (Edge), passcode CAN be passed through following above steps
2. When no 3G or Edge signal, above steps don't work

Conclusion:
Seems passcode security is related to network status
Possible security hole under Edge

I think you need to reprogram the module, you deleted the horn chirp and light flash confirmation. he dealer can reprogram for you.


Customer Preference Items NOTE: If using the WDS, select Module Configuration and Programming, then follow the screen prompts.
NOTE: Make sure module is listed as supporting customer preference items and supports the specific item to be configured in the Module Configuration Index in this section.

1. Select Service Bay Functions on the diagnostic tool.

1. Select the module that contains the customer preference item to be programmed. Refer to the Module Configuration Index in this section.

1. Select Customer Preference Items on the diagnostic tool.

1. Select Module Option Content.

1. Select the item to be enabled or disabled.

1. Enable or disable the item as necessary to reflect the customer preference.

------------------------------------------------------------------------

----------------------------------------------------------------------------
Principles of Operation
Power Door Locks
The generic electronic module (GEM) controls the power door lock and keyless entry system. Lock and unlock operation is achieved through the use of internal relays in the GEM. The relays are all door lock, all door unlock and driver door unlock. The normal path of the relays is to ground.
Pressing the door lock control switch to lock or unlock sends a ground signal to the GEM. The same GEM pin is used for unlock and lock input. The unlock signal is a direct connection to ground. The lock signal is altered by an internal resistor in the door lock control switch. This varied resistance identifies lock or unlock command to the GEM.
The door locks can also be controlled by the door key cylinder switches. For the liftgate door lock switch, turning the key to lock or unlock sends a ground signal to the GEM. The GEM will then ground the all door lock or all door unlock relay supplying voltage to the actuators. Turning the driver door key cylinder to the lock position sends a ground signal to the GEM. The GEM will then ground the all door lock relay supplying voltage to the actuators. Turning the driver door key cylinder to unlock sends a ground signal to GEM. The GEM will ground the driver door unlock relay and supply voltage to only the driver door actuator. If a second unlock ground is received within three seconds of the first, the GEM will ground the all door unlock relay supplying voltage to the passenger door actuators (if 2-stage unlock is equipped).
Keyless Entry
The keyless entry remote transmitter sends a signal that is received by the GEM internal antenna. Depending on the signal received, the GEM module will ground the appropriate internal relay and lock all doors or unlock the driver door. If the unlock signal is received again within three seconds of the first unlock, the GEM will ground the internal all door unlock relay unlocking all doors. The lock and unlock relay output to the actuators is controlled by the GEM, the same as power door lock operation from the control switch.
If the signal received is for the panic button, the GEM will cycle ground to the park lamp relay coil and horn relay coil. The park lamps and horn will continue to cycle until the panic button is pressed again or the ignition switch is turned to the RUN position, or after the timer expires.

Hello barbarafreel,

Your machine type is a FAV6800A correct? If so I would try to recycle 120VAC power to the machine. Pull the washer power cord for 30 seconds then repower backup. Do you still have the Lid Lock LED lit? If so further trouble shooting is required. I would next have you go into Service Mode. Once in Service Mode we need to go Board Output Test on page 16 of the Service Manual I will summarize below.

Here is the FAV6800A/FAV9800A Service Manual for your machine. Follow all safety warnings when working on the machine.

Let’s see if you can get into Service Mode, from the Service Manual slightly modified;

Enter Service Mode by pressing and holding the Enviro Plus and Spin Only keys simultaneously for three seconds or the display reads “00”

Now look at page 16 of the service manual let’s see if you can with the Board Output Test function unlock and lock the Left and Right Lid Locks.

Now press the Delicates key.

The LED display should show ot and the Quick Wash led will be lit.

The Left and Right Lid Locks will lock.

Now press the Extra Rinse key pad.

A few seconds should elapse and the Whites led will go lit for a short duration then off and in a few seconds the Lid Locks should unlock. Do the Lid Locks unlock?

Now press the Colors / Jeans key pad again.

Do the Lid Locks lock?

Let me know what action took place and we will go from there.

You can get out of Service Mode by pressing Enviro Plus and Spin Only keys simultaneously or press the Off key.

What I suspect is one of the lid lock is not releasing completely which moves a slide switch in the lid lock to signal the control board that the Lid is Unlocked and the Lid is Locked.

If you still have the issue I would release the washer top form the base and unplug the Right Lid Lock and see if that right lid lock is signaling incorrectly and possibly causing the issue. The Service Manual will show you how to release the washer top from the base. The left lid lock because of its dual signaling function “the Lid is Open/the Lid is Closed” and “the Lid is Locked/the Lid is Unlocked” can’t simply be unplugged. If you pull the Left Hand Lid Lock plug you will show a OP or OD error from the Control Board. If you are up for the troubleshooting I will help you proceed further.

Only the Left Lid Lock assembly needs to be plugged in for the washer to work as designed. I removed my Right Lid Lock a year ago and would never spend the money to replace it my choice.

A: The TV is in Showroom mode. The following steps will help you switch to Home mode. 1) Press Menu button from the remote,
2) Press Down arrow key until you see the word Picture, then press the Right arrow key,
3) Press Down arrow key until you see Mode, then press the Right arrow key,
4) Press Down arrow key until you see Power Up, then press the Right arrow key,
5) Press Down arrow key until you see Home, then press the Enter key,
6) Press Menu button four times to exit out from the OSD Menu.

see there is power in monitor and check also that your monitor is getting signal from cpu just remove the data vga data cable from cpu and see is it showing any massage on screen like check signal or any other massage. and check your keybord also by pressing num lock key see the light is on and aoff when you pressing the num lock button . if nothing is happen that mean your monitor is not getting signal from cpu and it is not monitor problem . bye