Question about HP Officejet 7210 All-In-One InkJet Printer

1 Answer

It will start to print and then stop in the middle and tell me that the cartridge is jammed. It will print the document after i say ok but it is not aligned correctly. I have tried a new cartrigde, cleaning and aligning it but these have not worked.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 192 Answers

Contact the manafactuer in this they may be able to help ypu our send you a new one.

Posted on Jul 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jam in top 3015d


Sir/Madam

Occasionally, media becomes jammed during a print job. An error in the software program and a jam message on the printer control panel display indicate a media jam. To prevent a jam, see the following instructions:
  • Only print on media that meets HP specifications.
  • Only print on media that is not wrinkled, folded, or damaged.
  • Make sure that the printer is clean.
  • Make sure that the input trays are loaded properly and are not too full. See the start guide for more information about loading input trays.
When adding new media, always remove all of the media from the input tray and straighten the stack of new media. This helps prevent multiple sheets of media from feeding through the printer at one time, which reduces media jams

Clearing a media jam


CAUTION: Media jams might result in loose toner on the page. Use cold water to wash toner off of clothes, as hot water will permanently set the toner into fabric. To remove toner from hands, wash hands in cold water.
CAUTION: Do not use a sharp object, such as a pencil or scissors, to remove jammed media.
NOTE: When clearing jams, including jams in the output bin, always push the print-cartridge-door release to open the top cover, and remove the print cartridge. Keep the top cover open and the cartridge out until the jam has been cleared. Opening the top cover and removing the print cartridge relieves tension on the printer rollers, which makes removing jammed pages easier.


Push the print-cartridge-door release and open the top cover.
Figure 1: Pushing release and opening top cover

3f0c0681-aab8-41b1-8ccc-edbc8d10b083.gif

Grasp the handle of the print cartridge and remove it. Set it aside.
Figure 2: Removing print cartridge


1135f64a-e54d-412a-a38c-2d53092ee8b0.gif

CAUTION: To prevent damage to the print cartridge, do not expose it to light any longer than necessary. Place the print cartridge in a paper bag or other opaque container until it can be placed back in the printer.

With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the device.
Figure 3: Jammed media most visible


38cea87e-25d6-4cfb-86b2-bbc3d933d279.gif

When the jammed media is removed from this area, replace the print cartridge.
Figure 4: Replacing printer cartridge


47beeaaf-6bbe-4681-9d09-8b877270789e.gif
Press the supporting springs, and close the top cover.
Open the media input tray and remove any media from the tray.

359bf88b-3c84-4de1-861e-08b6fe39b01f.gif
Slide the media guides inward as far as they will go. Press and hold down the tabs inside the media input tray, and slide the media input tray out of the printer.
Figure 6: Removing media input tray


92329010-15d2-4a56-a894-eacfba561eac.gif

With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the device.
Replace the input tray into the device.
Figure 7: Replacing input tray


141b20dd-a71b-4e53-86c1-b5e589fa0d60.gif

After clearing the media jam, it may be necessary to shut down the printer, and then turn it on again.

NOTE: To add new media, remove all of the media from the input tray, straighten the stack of media after adding the new media, and then place the stack in the tray.
Clearing other media jams
CAUTION: Do not use a sharp object, such as a pencil or scissors, to remove jammed media.
If the media has jammed where it exits the printer, grasp the leading edge of the media and pull the media out through the output bin.
Figure 8: Removing jammed media from output bin


b9b1737a-16cc-4bd2-b9a7-77bad78ef641.gif

NOTE: If the printer is shut off before clearing the media jam, turn it on again, and then restart the printing or copying job.
Tips to avoid media jams
Make sure the automatic document feeder (ADF) media lever is in the correct position for the media being used. Slide it to the single-sheet setting (to the right) when scanning on thick media. Slide it to the multiple-sheet setting (to the left) when scanning on regular media.
Make sure that the input tray is not overfilled. The input tray capacity varies depending on the type of print media that is used.
Check that the input tray is securely in place.
Do not add print media into the input tray while the printer is printing.
Use only HP-recommended media types.
Do not let print media stack up in the output bin. The print media type and the amount of toner used affect the output bin capacity.
Check the power connection. Make sure that the power cord is firmly connected to both the device and the power supply box. Plug the power cord into a grounded AC power outlet.
Media jams occur in the automatic document feeder (ADF)

Occasionally, media becomes jammed during a copy, scan, or fax job.

A software error message indicates a media jam, and the Doc feeder jam Clear, Reload message appears on the printer control panel display to indicate a jam.
  • The ADF input tray is loaded incorrectly or is too full.
  • The media does not meet HP specifications.
Typical automatic document feeder (ADF) jam locations Input tray areas: If the page is sticking out of the input tray, try to remove it gently from the input tray without tearing the page.
Figure 9: Removing jammed media from input tray


ec9c59d7-7daf-42c3-ba56-dc15042f3605.gif

Output paths: If the page is sticking out of the output bin, try to remove it gently without tearing the page.
Figure 10: Removing jammed media from output bin


e710c656-d551-4439-940d-878a82196f67.gif

  • Intermediate location: If the page is sticking out of the input tray and into the output area, see "To clear a media jam from the automatic document feeder (ADF)" below for instructions.

Automatic document feeder (ADF) media lever If a thick media is being used, slide the media lever to the single-sheet setting (to the right). Load a single sheet of media into the ADF.
When the copying, scanning, or faxing jobs are complete, slide the ADF media lever back to the multiple-sheet setting (to the left).
Clearing a media jam from the automatic document feeder (ADF)
  1. Using both hands, pull the printer control panel door toward you.
    Figure 11: Opening printer control panel door.
c5ce49eb-752a-4d44-bf67-99b4b9a44cc5.gif

  1. Remove any jammed media. Figure 12: Removing media
0cf6dfd4-a8b2-4153-8e19-52b3105abfda.gif

NOTE: Use only your hands to remove jammed media. Using other objects can damage internal parts.
Make sure that all of the pieces of media are removed, and then close the printer control panel door.
Figure 13: Closing printer control panel door


375c734d-e4be-4fed-b8ec-47628408dd9f.gif

I Hope Your HP Printer Problem Resolved By Now,In Case You still Having HP Printer Problem Then Visit Official HP Printer Website Below Link URL:

HP Printer Issue:
HP Support document HP Support Center

Or

If You still need HP Printer assistance Then Follow Us On :


HP Printer Support

Feb 13, 2014 | HP LaserJet Enterprise P3015d BW laser...

1 Answer

Jam cartrige Area


Clear jams from the print-cartridge area




1. Open the print-cartridge door, and remove the print cartridge.
Figure 18: removing print cartridge





2. With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the product.
Figure 19: removing jammed media


3. Replace the print cartridge and close the print-cartridge door.
Figure 20: reinstalling the print cartridge



For any other Jam types Visit the following link : HP Lasterjet M1522

Regards,
Shrey

May 30, 2011 | HP LaserJet M1522nf Multifunction Printer...

2 Answers

Red light stays on and printer won't print


My C60 Epson Stylus printer is not printing. First of all the paper jammed, I pull the paper from the front and since then the catridge holder is not going to the middle to print. also the green light keepon flashing and the red light stays on. I need your help.

Jan 16, 2010 | Epson Stylus C60 InkJet Printer

2 Answers

Paper Jammed. Have appeared to remove all paper. But I keep getting "Carriage Jam, open door, clear carriage jam then pres OK" message. Message on my computer screen says "The print cartridge carriage is...


HP support has extensive documentation for both paper and carriage jams for your model:

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00304007&lc=en&dlc=en&cc=us&lang=en&product=391182

I hope this helps!

Dec 10, 2009 | HP OfficeJet 7310 All-In-One InkJet...

1 Answer

Print half of full page


If the printer starts to print and stop in the middle check the eletricity of your place, this may have a variation. If the printer prints a half page and give you the paper, with no jam, check the cartridges and then the main board.

Aug 13, 2009 | Lexmark X5470 All-In-One InkJet Printer

1 Answer

It starts printing, then stops, the printer cartrige is jammed


Try emoving the duplex cartridge on the back (return printer to it's original configuration) and try printing. If the printer prints OK, then re-attach the duplexer checking for anything that could interfere with the print cartridge.

If the printer doesn't print, then I suspect something has fell into the printer and is creating enough resistance for the printer to detect and report. Turn the printer off, Remove all the cables from it. Try inverting the printer and gently shake it to see if anything falls out that could be jamming the printer cartridge.

Jun 02, 2009 | HP OfficeJet Pro K8600 Printer

1 Answer

Incorrect Cartridge Print cartridge in right stall not supported?


I changed the cartridge and it now works. I resent this though because it had been merrily printing before it decided it would stop and I have had to waste a three quarters full cartridge! I just hope the new one does not go the same way

Apr 08, 2009 | HP PhotoSmart C4180 All-in-One Color...

1 Answer

Vertical middle badly printed band


Hello sir; Make sure the glass is clean before you change another new cartridge.

Mar 31, 2009 | Sharp Office Equipment & Supplies

1 Answer

Printing Dillema


Flashing resume light also can mean:

1. cartridge is missing or an incorrect print cartridge is installed
2. cartridge is out of ink
3. dirty cartridge contacts
4. paper jammed

Check are cartridges firmly snapped into place and not empty. Use water to wash copper on cartridges if contacts are dirty.

Oct 30, 2006 | HP DeskJet 690c plus InkJet Printer

Not finding what you are looking for?
HP Officejet 7210 All-In-One InkJet Printer Logo

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...