Why does the internet port light only green? - Computers & Internet

Note that incoming traffic will cause the WAN (or Internet) light to blink even if it is 'probe' traffic trying to break in to your network. Such traffic is to be expected and is the reason you have firewall functionality in your gateway router.

On the inside, there is a bit of traffic on any LAN when the computers are turned on. Messages generated by the router itself are used to find computers and printers for a lot of different legitimate reasons.

only IPS can sure that. if model reset fails
no kidding call them. like millions do per day worldwide.
the ONLINE led must glow, the manual is clear about LED
and connected is no it, online is first. on modems and in this case the modem side of router./modem.
3347w = wireless
LED DSL goes green solid but blinks as DSK trains and conn.
and
LED interenet solid green connnected. blinks for data and red = fail.
page 205 in 3000 series manual
google it read it..

online means internet, and fails for you
and means call the ISP any time the internet led goes dead or red
it is that simple. do it.

Follow this steps
1. Connect the provided power adapter from the gateway's POWER port to an electrical outlet. The POWER light on the front of the gateway should be green. 2. Connect the provided gray phone cable from the gateway's PHONE LINE port to the DSL filter jack labeled DSL/HPNA. 3. Connect the yellow Ethernet cable provided with the gateway from the LOCAL ETHERNET port on the gateway to your computer's Ethernet port
With your computer completely started, verify the POWER and ETHERNET indicator lights on the front of the 2Wire gateway are green. If they are not, see "Understanding the Indicator Lights" on page 15. The INTERNET indicator light will not turn green until the gateway software has been installed and an Internet connection has been established.

you can run a direct line to that router and go to the cisco web site and get the information you need to run that router. its a pdf format and is 2.56 Meg. Try this

SecureEasySetup (Orange/White) The Cisco logo is the Router's SecureEasySetup button. It

lights up and will stay orange when the Router is powered on. The color orange indicates that

the Router is not using the SecureEasySetup feature, while the color white indicates that the

Router is using the SecureEasySetup feature. When the Router enters SecureEasySetup

mode, the Cisco logo will turn white and start flashing. After the Router has generated

the SSID and WPA Personal key, the Cisco logo will stop flashing and stay white.

To clear the SSID and WPA Personal key, press and hold down the Cisco logo for five seconds.

The Cisco logo will flash slowly as the Router resets itself. The Cisco logo will turn orange to

indicate a successful reset.NOTE: SecureEasySetup is a feature that makes

it easy to set up your wireless network. If you have SecureEasySetup devices, run the Router's

Setup Wizard CD-ROM and follow the onscreen instructions to use SecureEasySetup.

Power (Green) The Power LED lights up and will stay on while the Router is powered

on. When the Router goes through its selfdiagnostic mode during every boot-up, this

LED will flash. When the diagnostic is complete, the LED will be solidly lit.

DMZ (Green) The DMZ LED indicates when the DMZ function is being used. This LED will

remain lit as long as DMZ is enabled. WLAN (Green) The WLAN LED lights up when

the wireless feature is enabled. If the LED is flashing, the Router is actively sending or

receiving data over the network. 1, 2, 3, 4 (Green) These numbered LEDs, corresponding with the numbered ports on the Router's back panel, serve two purposes. If the LED is continuously lit, the Router is successfully connected to a device through that port. A flashing LED indicates network activity over that port.

Internet (Green) The Internet LED lights up when there is a connection made through the

Internet port. A flashing LED indicates network activity over the Internet port.

Good luck

1. Here is the user manual found at this site.
ftp://downloads.netgear.com/files/wgr614v5_ref_manual.pdf
save to hard drive >> desktop and read the "troubleshooting Tips " section page 3-8
check your router connections >> Ethernet cord to the LAN port in the back or the router to the computer.
Ethernet cord to the WAN Port from the DSL port

Connections

> Blue 15 pin or white 16 pin colour port is for monitor.
> 3 pin female port is for power cable for Computer Tower
>3 pin male power cable is for monitor
> Purple and green colour port is for Keyboard and mouse if they are ps2 (round connector) if usb then connect in any usb port.
>Small 3 colour ports Pink,Green,Blue is for sound.Connect only the Green colour cable coming from speaker to green port
>Connect the speaker Adapter cable to the wall socket for supplying power to speakers.
> RJ45 (Ehternet port-port which looks like phone connector but little bigger will connect Internet cable if you have internet.

Connect and Enjoy

Please make sure that the router is properly configured then only the internet light will be green

Talk to your ISP regarding the router configuration

is your router powered? make sure your router is powered properly.

are you connecting your computer to the LAN ports? (the ones with a number not the one that say WAN? connect your computer to one of the LAN numbered ports and check to see if you get a green light on the front pannel. if you don't have green light, try a different port until, if you run out of ports and still no green light try a different cable.

have you by any chance disable your lan ports? I don't know if it is possible on your router to disable some ports, if that's the case is better to start fresh and simply reset your router by pressing a reset button for a minute while your router is getting powered and retest to see if you a green light on the lan port where you are connecting your computer.

if all this fails, it's very likely that your router has died. replaced accordingly.

please use a different router and check. also check using a differen splliter first.

its a problem in your internet-router. try to reset it, and plug it into the back of your ps3, then you should be able to do something with it