My Weather station is not working. I have tried to reset and have replaced batteries with new one but it still does not turn on. Anyone have any help?

This says it is easy to set up, but there is a Fixya post that says there are a reset button in both units. In mine, I have to put a new battery in the main unit and then remove and replace the button in the remote unit.

https://www.techwalla.com/articles/sharp-wireless-weather-station-instructions

Instructions for sharp SPC595 wireless weather station - Fixya

https://www.fixya.com > support > t21517987-instructi...
Nov. 17, 2013 - Try pushing the reset button on the inside of the battery compartment of the remote unit then push the reset button on the back of the main unit ...
Owners manual for sharp weather station spc 595
Feb. 10, 2013
How do i set the time zone on my sharp weather station
Oct. 20, 2014
SOLVED: Set spc 595 sharp weather station
Jan. 29, 2014
How to set clock on sharp spc595?
May 27, 2014
More results from www.fixya.com

There is a Manual for the SPC775 unit here

https://fccid.io/ZY9-SPC775/User-Manual/Users-manual-1542888

..

There are a couple of possibilities for the failure to transmit/receive outdoor data. First, resynch the two units. This will depend on the manufacturer. For some brands, you need to take the batteries out of both the indoor and outdoor units for 10 minutes. Then put the batteries into the devices with both side by side (working inside is easier). Wait until the outdoor data is displayed. There are some weather station systems where the outdoor unit isn't weather-proof. You may need to dry the outdoor unit for several days after removing the batteries before resynching it to indoor sensor.

If the data displays properly when the outdoor unit is inside, you may have the outdoor sensor too far away from the indoor unit. (The distance will depend on the number of walls and the composition of the wall studs/siding.) Try keeping the two units closer together.

If the outdoor data isn't displayed when the two units are side by side and the reset procedure doesn't work. One device has an internal malfunction (transmitter or receiver failed). It's probably best to replace the unit. If it is under warranty, contact the manufacturer.

I hope this helps. For specific details on resetting the indoor and outdoor units to synch them, please add a comment with the make/model of your weather station.

Cindy Wells
(I've seen Davis Weather stations damaged by a close lightning strike. The outdoor unit had to be replaced.)

Remove the batteries from both the sensor and weather station. Keep both units close together on the same table. Press any button on the weather station 20 times to remove any random energy from it. Replace batteries in sensor and then in weather station. Do not press any buttons on the weather station until the sensor data appears on screen. It worked for me!

Hi,
I always have trouble getting mine to work after changing the batteries, but I have just managed to get it going by doing the following:
taking batteries out of main unit
putting new battery in remote unit and pressing remote unit reset button
re-inserting batteries in main unit and pressing reset button.

i think the trick is to ensure that the batteries go in the remote unit first, then the main unit after that. It has taken me days to work this out!

http://www.acurite.com/advancedsearch/result/?q=1099RX

There is no reset button, installing new batteries causes the sensor to reset itself.

Try removing and re-installing the batteries.

Good luck,
Steve

Is the outside unit LED on? I replaced the battery on the outside unit and in doing this reset the outside information.

I have an Oregon WMR928NX weather station. I have replaced the alkaline batteries in the wind and rain sensors. These did not communicate with the main unit, so I reset both units but only the wind sensor communicates. I have checked both battery voltages on the cuircuit board and both are correct, I don't know a solution. Thanks Rob

Push and hold down the channel button, wait for beep, then on the sensor, push and hold the tx button, wait for beep.

check if you have the US standard or international standard, like FD. or CD...........

and check your pda the loation where you set is right.

and try to reset a new website for your PDA weather software for updating. becasue different websites may be vary