My topfield wont go past main recording on the screen. How do i reset it

https://www.manualslib.com/manual/807951/Topfield-Trf-2100.html


Topfield TRF 2100 User Reference


Page 30 of online manual shown.

On some models this reset may work, disconnect TV from outlet, press and hold the power button on the TV itself for about 30 seconds. Wait a minute, plug the set back in and press power button once.
Hope this helps cuz I don't know otherwise..but thought i'd share.

Why wont my rca tablet load past the RCA logo screen? - I ...

www.askmefast.com > Consumer Electronics > TVs > Tablet

Laptops & Notebooks .... My rca tablet wont go past the first logo screen and i have factory reset it and ... Some how the factor reset button on the back of my rca 7in tabletgot pushed and ..... Rca tablet will not play games it just goes back to home screen ....My rca 7 tablet is stuck at the main screen and it won t go any further.

my rca tablet won't turn on I tried charging but it's not working ...

www.tomsguide.com/forum/id.../rca-tablet-turn-charging-working.html

Dec 15, 2015 - 12 posts - ‎10 authors
My rca tablet isn't working I tried charging it but it's still not turning on ... Hold them both in this position until you get a menu on the screen. .... I've repeated this attempt to turnit on it just flashes on the battery logo with an exclamation point ... SolvedMy Asuslaptop model Q551L won't turn on or charge what ... Tablet keeps turning off - Battery
9 posts
Nov 16, 2015
My tablet won't turn on! - Battery
10 posts
Jun 19, 2015
RCA tablet no power-up - Power Up
5 posts
Mar 30, 2015
Help! My tablet won't turn on! what do I do?! - Asus
50 posts
Nov 5, 2013
More results from www.tomsguide.com

If at all possible, a whole new fresh start means, "Reformat".

Backup if at all possible and then go ahead & follow the steps to Reformat.

Note:.... Reformat will erase everything and you will have a laptop, like when you first bought it.

Good Luck

Try holding many buttons at one time for 30 seconds...use toes if needed.

follow this test and fix it. God bless you
However if after your did this, you need to open the r. control and clean the keypads from dirty, oxide, corrosion with contacs cleaner and replace the old batteries, clean the springs contacst from oxide, corrosion and try again.
The connections between the tape deck and the amplifier's L and R TAPE OUT jacks are incorrect or loose. Turn off the amplifier and correct the connections. The source selector is set to the wrong audio source. Set the selector to the source you want to record.

out put from the dj stuff to the input lines on the amp your using to record on, once the CD or tape, or whatever your recording onto, is set to record, it should pick it right up , now if your doing all of this off your DJ equipment everything that's used, from record players, to CD to tape, will be run through the main amp your using, if the selection switch is set to whatever, you should be able to just turn on the unit your recording to, and it will pick it up , everything leading to the main amp will be plugged into, a line in, and some, ( tape player ) will also have a line out, ( so should the cd player if its a recordable one, which in turn would be supplying the lines output to each unit .

Hi,
If both your yahoo messed up, kindly create another yahoo ( carefully record the data of this yahoo as this will as alternate email from yahoo). After done , please loggin again the dixebaby....., then click forget password ( you should asked alternate email, then write down your new yahoo). Then open your new yahoo to reset / get new password your [email protected]). Do the same way with [email protected]

Regards,

just bought a Topfield trf-2460 PVR and I have got everything working except the remote control (that came with pvr) sound funtion. I can record and playback with the audio working fine but even after setting the TF remote control to work on the TV funtion, it just doesn't like it, except for the mute button, that and the off function. Any suggestions would be appreciated. Joe

From SP510 camera switched off:
1. Turn dial on top plate to movie mode (selections from the menu screen apply to the mode the camera is set in);
2. Switch on SP510 power;
3. Press "MENU" button on back plate;
4. Select "Camera Menu" from screen if not already on it, using navigation buttons on back plate
5. Scroll down yellow "Camera menu" tabs to microphone picture (below "Digital Zoom"), which may be showing "off". Select OK and toggle yellow tab from "off" to "on", then press OK button.
6. Microphone tab should now show "on".
7. Return to main menu (press MENU button).
8. Return to image screen (press MENU button).
9. Test to see if video now records sound.
10. If is still doesn't record sound, try "reset" from video menu screen (this will reset the movie mode to factory settings, including microphone on).