Question about Generac Inverter Ix2000 Gas Portable Generator......new

1 Answer

I have a generac ix2000 and has an overload light on with no AC power out. what do i need to check?

The only thing i've done is check the voltage coming out the plugs but i get no readings

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,162 Answers

When you have a generator with a inverter in it you have to be careful of overloads an static electricity. More than likely one or more otf the MOSFETs has blown. An inverter is really a switching supply. Not very hard to replace parts but if you have spme skill with electronics take it apart an give it a go. If transistors have not blown you may find a blown fuse inside on circuit board. You will never find a schematic for any of these units. They are protected because the dealers pay to much for selling rights you cant hardly get them. But i would take it apart an see what you have. Or find a good electronics guy an ask him to check it

Posted on Jan 28, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car has dieing while going dwn rd. Sometimes wjll start rght back up, other times we wait sometimes hrs. I've checked the coil pack& module both pcm &ecm were checked by g&s auto and said...


Code 17 & 18 are crank/cam correlation codes. Depending on what car you have, some sensors are dual sensor, crank and cam in one. Some are set up with up to three sensors. One crank and one or two cam sensors. I you have a dual sensor, I would replace it, but check the plug first. Sometimes corrosion can mess with sensors. Just unplug it and plug it back in. This usually takes care of contact issues. Clear the light and see if that code comes up again. If you have two or more sensors, then we are talking timing belt issues. To check code 26, you will have to check for voltage on that wire. Pinout and color codes are needed to find the wire from the ECM. Again not knowing your car, voltage could be 5,8, or 12 volts. Or real close to these numbers. If you don't see any voltage from here, the ECM is bad. Quad drivers either work or don't work. 56 is an 02 heater code. This could make the car run a little rough, but not cut out. Now the injector test, if you didn't get a reading from the injector, it is bad. This will make the run real bad, Because you lost that cylinder.

Jul 13, 2013 | Cars & Trucks

1 Answer

Obd2 code p0562


Low battery charge, Battery Defective(Could have a bad cell), Loose or missing alternator drive belt, Faulty Alternator, Open or short system voltage circuit

Apr 11, 2017 | Mazda RX8 Cars & Trucks

1 Answer

OBD2 CODE READER P0562


Make sure your 12V grounds to engine and chassis are good.

Apr 11, 2017 | Mazda RX8 Cars & Trucks

1 Answer

Random misfire/distributor problems


IF you have a seperate coil (1 coil only) check for correct voltage for the coil as most start on 12 volts and run on 7 volts and have a resistor in the circuit. Randomj misfire may be the coil breaking down as it gets too hot from the incorrect voltage

Feb 23, 2013 | 2002 Chrysler Sebring

1 Answer

Centurion 5000W/6250W starting - little voltage at outlets. I plugged in a voltmeter into the 110 plug and voltage is present, just a magnitude of 10 less than what it should be. so, there is 's


Try to find a way to ascertain if it is up to speed. Either check rpms or frequency of the AC voltage. If it is < 60 hz the engine is likely running too slow, thus the low voltage.

Sep 18, 2017 | Electrical Supplies

1 Answer

Brothers sewing machine


first check the outlet to see if it works
next check to make sure the power cord is plugged into the machine
correctly.
if you've done the above things, & you push the switch to turn the machine on & it still won't come on, then the machine needs to be
checked.

Sep 05, 2012 | Brother Sewing Machines

1 Answer

I have changed the spark plugs on my 2005 C2 VTS and now when I start the car the engine warning light comes on and it beeps at me. Don't think I've done anything wrong, have checked everythin


try to recheck the spark plug distribution cable arrangement otherwise check your spark plug may be one of it is short or the gap is not proper.

May 04, 2012 | 2004 Citroen C2 VTS

1 Answer

I have a 2001 Explorer Sport Trak and it don't want to start. We have checked all the sensors (crankshaft, cam trigger, fuel pump pressre is 65). What is the tank fuel pressure sensor voltage reading. ...


The first thing to check would be spark. This can be done by connecting a spark plug tester to a plug wire while the engine is cranking. The tester must be grounded to the engine block for a good electrical connection.. Your fuel pump pressure is OK.
The problem should be electrical so check
1. No voltage to the fuel injectors (blown injector fuse or bad relay)
2. No pulse signal to the injectors from the PCM (no crank or cam sensor input to the PCM, or a bad driver circuit in the PCM, or a wiring harness problem)
3. A shorted fuel injector (robs voltage from the other injectors so none will operate)

Jan 08, 2011 | 2001 Ford Explorer Sport Trac

Not finding what you are looking for?
Generac Inverter Ix2000 Gas Portable Generator......new Logo

4,839 people viewed this question

Ask a Question

Usually answered in minutes!

Top Generac Electrical Supplies Experts

Sheldon Dedek

Level 3 Expert

909 Answers

Bob Janelli

Level 1 Expert

26 Answers

JOHN LAPIER

Level 3 Expert

2591 Answers

Are you a Generac Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...