How come, when I answer a question then go back, it takes me to the beginning and not to my previous screen?

A previous answer on this site from Zann_e for another model of Shark sewing machines suggests that you unthread the machine, remove the bobbin, clean the bobbin chamber, turn off and leave unplugged for 45 minutes and put it all back together again. The previous answer suggests that when there is no tension that you encounter the problem you are posting about. Hope this helps.

press f8 vigorously as the computer begins to boot. this should take you to the windows start options screen, which includes diagnostic tools such as windows repair/restore and safe mode.

Windows repair (repair your computer) has a start up repair function which you can attempt, and if that does not work, there is a windows restore (from previous back up/restore point) in the repair utility as well.

If neither of those features work, choose "run in safe mode(/with networking)" at the f8 windows start options screen instead of "repair my computer". it may be usable in safe mode, and safe mode may reveal more clues about an actual hardware malfunction.

long story short, f8 before windows begins to cycle up.

You can access the answering system remotely by dialing your home telephone number from any touch-tone telephone. To remotely access the answering system
Dial your telephone number from any touch-tone telephone. When the answering system answers, enter the two-digit remote access code (19, unless you have changed it). The answering system automatically announces the number of messages (new or old) if there are any. If there are new messages, the answering system automatically begins to play new messages only. -OR If there are no new messages, the answering system automatically begins to play all old messages. You can also enter the remote commands: Play all messages
1 Press to listen to all messages. If there are new messages, the system plays back only the new messages (oldest first). If there are no new messages, the system plays back all old messages (oldest first). Play new messages
2 Press to listen to new messages only. Delete a message 3 Press during message playback to delete the current message. Delete all old messages
3 Press to delete all old messages. Replay current message or previous message
4 To repeat the message currently playing, press 4 after the answering system plays the day and time the current message was received. To listen to the previous message, press 4 while the answering system is playing the day and time the current message was received. Stop
5 Press to stop playback and recording. Play help menu * 5 Press to listen to a list of remote commands. Skip to next message
6 Press during playback to skip the current message and advance to the next message. Record a announcement
7 Press to record a new announcement. Begin speaking after the long beep. Turn system on or off 0 Press to turn the answering system on or off. Exit
8 or hang up Press to end remote access (the call is terminated). 1. 2. 3. 4.5
0 Answering system Remote access Hang up to end the call and save all messages.
NOTES: If you do not enter a valid remote access code, the system answers the call automatically. If the date and time is not set when a message is recorded, the system announces, "Time and date not set" before the answering system announces the number of messages. If there are no messages in the answering system, the system announces, "You have no message." If there are no new messages in the answering system, when you press 2 to play back new messages, the system announces, "You have no new message." If you pause for more than four seconds during remote access, you hear a help menu listing all features and commands. If there is no command for another 20 seconds, the call ends automatically. If the memory is full, the answering system answers after 10 rings and announces, "Memory is full. Enter the remote access code." Enter your remote access code to access the messages and announcements. When the answering system is turned off, the telephone answers after 10 rings and announces, "Please enter your remote access code."

If you have previously backed up your iPad, you can

• connect your iPad to your computer,
• open iTunes
• select your iPad
• in the Summary screen, press the "Restore Backup" button

After several minutes, your backup will be complete and your previous data restored.

If you did not back up your iPad previously (either to iCloud or to your computer), you won't be able to restore your old data. Also, be careful not to backup your new iPad until you have restored the old backup (in the Backups section of the Summary of your iPad in iTunes, it notes when your last backup occurred).

If you need further help, reach me via phone at https://www.6ya.com/expert/john_77bb351c0c06b354

Look on the back, or sides of your tablet. You are looking for a little reset button, you will need a paper clip,,this should take you back original factory reset screen

Your answering machine is in "Announce" mode, where it does not take messages. You want to be in "Answer" mode where it will take messages. Since you neglected to specify the model of your Uniden cordless system I can only suggest you select it from the list beginning here to download a copy of the manual.

Try resetting your google account password by going to https://www.google.com/accounts/recovery

Then after you have reset your password on a computer, try the password on your phone. 

If that doesn't work try this:

Have someone call your phone.  Answer.  Leave the call connected. Push the "back" key over and over (NOT the home key) while leaving the call connected.  Keep the keyboard retracted.

Go to the home screen, go to settings, google account, add another google account, sign in to that--- (must have wifi connected, as you're trying to communicate with the google servers while you're on a phone call-- it will prompt you to turn on wifi if you forget)--  then end the call, and go back to the lock screen.  This time, I use the google account that u just added.  

buy a new one

take a knife and scratch(quite deep, would recommend a butcher's blade) perpendicular lines across the surface area of the screen, then pour finite magnesium into the cracks/scratches that you previously formed (make sure you use a good amount!) then take a safety match and stroke it gently across the match box to light it and begin to move it closer to your screen, you will slowly see the screen brightness functions come into affect, you can also adjust contrast in this manner as well as save electricity.

If qz. see previous answer. If it's mechanical and absolutely all the moisture is not eradicated then rust may begin to form and will over time cause damage. So if it's mechanical take it to a watchmaker for servicing asap.
Please rate my solutions.