How can i clean/disinfect my tub/jets really really well? Im not sure what is safe to use in my tub.

Hi Claude.
If your spa jets appear to be pulsating or pausing, first check to make sure your filter isnot clogged. If your filter appears to be okay, you should next take a look at your hot tub's water level. If there is too little water, air could be working its way into the system through the jets.

Why are My Hot Tub Jets Not Working? ' Master Spa Parts

How to Replace Water Jets in a Hot Tub

1. Turn off your hot tub. ...
2. Reach into the tub and grasp the outside edge of the damaged water jet. ...
3. Place your water jet face down on a level surface. ...
4. Line up the notched tab on the back of the jet with the groove inside the jet housing. ...
5. Turn on your hot tub.
6. Things You Will Need. ...
7. References (3) ...
8. About the Author.

How to Replace Water Jets in a Hot Tub ' Home Guides ' SF Gate

How To Clean Bathtub Jets with Basic Household Ingredients

1. Fill the tub until the jets are covered by 2-3 inches of hot water.
2. Add 2 Tablespoons of a low-sudsing dishwashing liquid and 1/2 cup of bleach. ...
3. Run the tub's jets for 15 minutes.
4. Empty the tub, and refill it (cold water is fine this time). ...
5. Drain the tub and rinse it well to get the gunk off.

More items...
•
4 Sep 2014

How To Clean Bathtub Jets with Basic Household Ingredients ...

or read up more at this link.

https://www.google.com/search?q=Aeromax+tub+some+jets+not+blowing+air&rlz=1C1AVFC_enGB797GB798&oq=Aeromax+tub+some+jets+not+blowing+air&aqs=chrome..69i57.7532j0j9&sourceid=chrome&ie=UTF-8

I would keep the washer lid open and the agitator and drum dry. However, you will have to, from time to time clean the machine.
Run a full cycle (tub empty of garments) with hot water and Clorox or other liquid disinfectant. Then air or towel dry the inside components. Read the manufacturer's cleaning instructions that came with your owner's / user's manual.

No they do not here is a simple way to clean the jets and the piping.

Regular Jet Cleaning

To clean the entire whirlpool system and tub exterior, follow this process every month or more frequently if needed. Don't let dirt and grime build up or you'll have more scrubbing to do to get the tub clean.

1. Fill the tub with hot water, approximately an inch above the highest jet.
2. Make sure the water temperature reaches at least 140? F (60? C).
3. Add 1/2 cup of laundry detergent or the amount used to clean 1 load of laundry as recommended by the detergent manufacturer.
4. Run the jets for 15 minutes.
5. Drain the tub and refill with clean lukewarm water.
6. Run the jets for another 15 minutes.
7. Drain the bathtub.
8. Dry the tub completely by wiping it down with a clean towel.

Always clean you jet tub as directed by the manual. If you don't have one, than fill tub above the jets, add liquid dishwasher gel (not tabs) with bleach and run through the jets for 20 minutes. Drain, fill with clean water and run two times to clean the tub and jets and then use. Be sure your metal filter is clean of hair and soap debris. This will keep your tub and jets nice and clean. Also recommend using Epsom salts and either essential oil of lavender or eucalyptus to your bath. Both essential oils have antibacterial properties. If you want it simpler, purchase Dr. Teal's lavender soak from the drug store. Happy soaking!

Here is a place you can go, the link is to Kohler however it dont really matter what brand you may have. The link will take you to the cleaning of an Acrylic Jetted Tub and there is also a link once there how to flush out your jetted tub and how often it should be done. Please give a 4 THUMBS UP if this free answer was helpful in any way. Good Luck and have a nice day.
www.us.kohler.com/tech/careandcleaning/wb_acrylic.jsp

It depends on the brand of jet and tub, if it is a gold or silver trim ring, they will generally pry off with a screwdriver, just be careful not to damage the tub when doing so. When prying, move the screwdriver around the jet an inch at a time, just like opening a can of paint. Some rings will screw on, but most just pry off.

Well.. Ummm... Yes. really to be safe & responsible & to prevent any more damage. Just having it hot & using for a little bit, may be OK, but no water jets etc. No Water Pumping jets etc.

Your system is infected with virus so your system has to be disinfected from safe mode with command prompt.

1. To disinfect the virus please download the latest sdat????.exe from this site and save it C:TEMP

2. Now restart the System and press F8 key
3. Select Safe mode with Command Prompt
4. Then change directory to C:TEMP
5. There type the filename and give the parameters as follows:

C:TEMP>sdat5372.exe /e

After few seconds in that directory you will find some files that extracted from the dat file.

6. Give commands as follows:

C:Temp>SCAN /all /adl /clean /report Report.log

This will clean all the virus in the system.

Hope this will helps you..

If this works please comment me.....

If they are just in the ceramic liner and not really through it you should be ok, they are caused by temprature fluctuations, maybe youve added vegies from the fridge part way through to an already hot dish...
I still use mine all the time with no problems, i mix a little bleach in a sink of hot water and rinse it well to really disinfect it after using it to be sure its health inspector clean
www.rivalproducts.com
customer support can give u more info if you wish