How do i retreive meessages from remote loaction with the security code on 5.8 system

this is pertinent to uniden dect 1653 series and may work on yours as most uniden systems use the same format
1--call your phone number and wait until the system answers( if it is turned off , it answers after 15 rings and sounds a series of beeps
2--- during the greeting or beeps , press the # and immediately enter your security code . If you enter it incorrectly 3 times , the system hangs up and returns to standby
3--- the system announces the time and the number of messages in the memory and a help prompt. It beeps to let you know it's waiting for a command
4--when you hear the beeping , enter , enter a 2 digit code command from from the chart for example to play a message press# then 2
if you don't press any keys for 15 seconds the system hangs up and returns to standby
the chart codes are
#1---repeat message
#2-- play message
#3--skip message
#4 --delete message
#5--stop play back
#6 turn system on
#9---turn system off
#0 hear help prompts
to get your security code -- programming a security code
the default security code is 80
1-- with the phone in standby, open the menu from any handset
2-- select ans setup, the select security code
3-- use the number keypad to enter a 2 digit security code ( any numbers in the 00-99 bracket) Press menu/ select when you are finished
remember to note your security code
if this doesn't work on your set up go google and type in user manual for (make and model ) cordless phones-- and print out any pdf version down loads

For RC-LRN Remote (5 digit coding)
Before starting, retreive the 5 digit codes for you device - I found all my codes at http://2getdtv.com/directv/remote_codes.html
1. Press button for the device you want to program ie DVD.
2. Press and hold Setup button until it blinks twice.
3. Enter 5 Digit Code (ie LG DVD =31531), the power button will blink once slowly
4. Then press power button to turn on/off device.
5. If code fails, try next code.
Note: Some codes work better than others.
Source: http://www.fixya.com/support/t7582447-program

1. Call your telephone number.

2. After you hear the beep that follows the greeting, enter your 4-digit security code. To bypass the greeting, you can enter your 4-digit security code at any time while the greeting is playing.

3. The unit plays the remote menu after the correct security code has been entered. Menu selections can be made at any time while the menu is playing.

The above is from page 19 of the manual at
http://www.home-electronics.net/ge/pc/IB/29869GE2_IB.pdf

To use your system from a remote telephone, you must first enter a 3-digit remote operation security code. The security code label is located on the bottom of the system.

1. Dial your phone number.

2. When your outgoing message is playing, enter your remote operation security code. Bd appears on the display to indicate the system is in remote mode.

If there are no new messages, you hear three beeps.
These are the remote codes available to you:

2 # Play all messages.
2 5 Play new messages.
3 # Delete all old messages.
7 # Record new outgoing message.
7 # Stop recording outgoing message.
8 # Record memo.
8 # Stop recording memo.
9 # Turn system off/on.
0 # Monitor the room..

hello after a long search through the net the only solution to retreive the code is through LG themselves you will need to send them an email with your dvd model they will email you the code
another solution would be to purchase a all in one remote this i think would be best as the codes come in the manul goodluck

For RC-LRN Remote (5 digit coding)
Before starting, retreive the 5 digit codes for you device - I found all my codes at http://2getdtv.com/directv/remote_codes.html
1. Press button for the device you want to program ie DVD.
2. Press and hold Setup button until it blinks twice.
3. Enter 5 Digit Code (ie LG DVD =31531), the power button will blink once slowly
4. Then press power button to turn on/off device.
5. If code fails, try next code.
Note: Some codes work better than others.
jm

Provided that your system is not programmed for coded override, the standard emergency override is as follows:

1. Enter the vehicle (the security system will trigger.)
2. Locate but do not press the valet/override switch yet (it should be a small black button installed under the dash within reach of the driver)
3. Turn the ignition key to the ON position.
4. Press and release the emergency override button (The security system will turn off).
Note: If the automatic arming feature is enabled on your system. The security system will re-arm the next time the ignition key is turn off and the vehicle's doors are closed.


If the coded override feature was enabled by the installing dealer, you will need to follow these procedure:

1. Enter the vehicle (the security system will trigger).
2. Locate but do not press the valet/override switch yet (it should be a small black button installed under the dash within reach of the driver)
3. Turn the ignition switch to the ON position.
4. Within 5 seconds press the emergency override button the number of times corresponding to the first digit of your personal code (Default digit is 1).
5. Within 5 seconds turn the ignition key OFF, then ON.
6. Within 5 seconds press the emergency override button the number of times corresponding to the second digit of your personal code (Default digit is 1).
7. Within 5 seconds turn the ignition key OFF, then ON.
8. If entered correctly the security system will turn off.
9. Turn the ignition key to the OFF position.

If the coded override feature is enabled and the code is lost, the system will need to be reprogrammed by an authorized dealer.

As long as you know your security code you can retreive your lock code. On the Lotus dial ##3282# scroll down to Advanced, choose View, then scroll down to option 5 which should be the Lock Code and select it. You will need to enter your security code here which typically is 6 zeros.

here's what my instruction booklet says:

Changing the Security Code

The default security code for accessing the answering system from another location is 1 2 3. You must use the handset to change the security code. With the phone OFF (not in TALK mode), follow these steps:

1. Press the FLASH/answerer/Call wait button to display ANSWERER REMOTE.
2. Press the *EXIT/TONE button.
3. Enter the new 3-digit security code.
4. Press the *EXIT/TONE button again. The unit announces the new code, pauses, beeps, and then announces the menu options again.

hope that helps

Remote transmitters have to have the program in it for the device you are trying to use it with, and the codes simply retreive the progrom, so there are no codes to install as it simply cannot be done. An original replacement can be gotten here: http://www.remotes.com/remotes/servlet/rs?a=Search&o=c&m1=HT-DB600&uid=11758875673120, or the original remote from Samsung is less expensive and can be gotten here: http://www.samsungparts.com/part_detail.asp?catalog%5Fname=Parts+and+Accessories&product%5Fid=AH59%2D01169L&search%5Fmodel=HTDB600 Good Luck