Nec front loader keep beeping with E2 on the screen

If you're experiencing an error on your LG front loader M80490CL washing machine, here are some steps you can try to clear the error:

1. Power off the washing machine by unplugging it or turning off the circuit breaker that powers it.
2. Wait for a few minutes to let the washing machine cool down.
3. Press and hold the "Start/Pause" button for about five seconds.
4. While still holding the "Start/Pause" button, turn on the washing machine by either plugging it back in or turning the circuit breaker back on.
5. Release the "Start/Pause" button once the washing machine begins to beep and the display shows "CL" to indicate that the error has been cleared.
6. If the error persists, refer to the troubleshooting section of the washing machine's user manual or contact LG customer support for further assistance.

Could be something hung up in drain pump

I have the same problem too ....
When turned power on it starts beeping E2

yes the intake valve has failed
or the machine is fitted with a low pressure valve and your using high pressure water supply
i recon the valve spring or something has failed
youll need to replace the cold water intake valve {ebay or local shop}
then clear the error by resetting the machine
mains off press button on the front main on wait 5 secs
usually they beeeep one long beep and your done

1 Beep/E10--Error: Water doesn't enter Cause: Water supply problem, Check kinks and faucets
1 Beep/E10--Error: Water leaks Cause: Water connections loose,household drain clog,oversudsing. Correct problems.
1 Beep/E10--Error: Dispenser drawer is open Cause: Washer will not operate if drawer is open.
2 Beeps/E20--Error: Water dosen't drain. Cause: Drain is kinked or household clog. Correct.
3 Beeps/E30--Error: Drum overfilled. Cause: Inlet valve,pressure switch or control board failure.Select drain/spin to remove water. Restart.
4 Beeps/E40--Error: Door is open. Cause: Washer will not operate if door is open. Close door.
5 Beeps/E50--Error: Motor is overheated. Cause: Wait 30 minutes to cool down. Restart.
7 Beeps/E70--Error: Cold water doesn't enter. Cause: Hoses crossed,faucet problem.
15 Beeps/EF0--Error: Oversudsing. Cause: Too much detergent,or improper detergent for machine.
15 Beeps/EF0--Error: Hot water doesn't enter. Cause: Hoses crossed,faucet problem.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

The error means that the water level (pressure) sensor is not working, you will need to replace it or call someone to so it for you.

Yes.
Child lock active.
Hold start button 10 seconds.
Then it will deactivate.

If this is not the case, door lock fault or main board fault.

I'll just take a swing at this one, without model number.............F-02 is typically a Whirlpool error code for " slow drain". If this is a Kenmore or Whirlpool front loader, pull off the bottom panel and check the pump filter, (pump should be right up front, turn counter-clock-wise to remove filter) clear of any debris, check hose from tub to pump as well. NOTE! If there is water in the machine, it will pour out of the pump, first remove the water either with a wet-vac, or just do it very slowly and carefully at the pump, draining the water into a pan.

The machine beeps E2 all the time. Actually E2 error code means washer door is not closed properly. However washer door does close properly, but the machine still beeps with showing E2 error code. Please help solve this problem.

Many thanks,

Robert

HATE TO SAY IT BUT THE BOARD WOULD NEED REPLACEMENT.BEEPING NORMALLY INDICATES A FAULT CONDITION WHICH WOULD STOP THE CYCLE(WASH) OR THE COMPLETION OF A CYCLE.