The feed button does not work at all - Casio HR-100TMPlus Calculator

Try wiggling the hand wheel while pressing the button.

How do I reset the cash register?

116ER, 117ER, CE2300, CE2350, CE2400, CE280, CE285, CE300, PCR202, PCR204, PCR308, PCR408, PCR350, PCR355, PCR360, PCR365, PCR450, PCR460

This will erase all information - Remove AA batteries and unplug register from wall for 15 minutes.*

If resetting does not work this indicates issue is repair level.

PCRT465, PCR465A, PCRT2000,

This will erase all information - with the PGM key at Off press and hold down the Feed button, while holding the Feed button turn the PGM key down to the PGM mode Release the Feed Button ----INI should appear or a group of 8 zeros

If resetting does not work this indicates issue is repair level.

PCRT470, PCRT480, PCRT48S, PCRT2100, PCRT220S

This will erase all information - with the PGM key at Off press and hold down the Feed (journal) button, while holding the Feed button turn the PGM key down to the PGM mode Release the Feed Button ----INI should appear or a group of 8 zeros, now press one of the below

22500 Subtotal (PCRT40, 480, 48S)

Or

23000 Subtotal (PCRT2100, 220S )

Wait for a receipt to print.

If resetting does not work this indicates issue is repair level.

A fix from a forum:

Procedure 1 We found this procedure to work for the Stylus Photo 1270 type printer, and understand that it also works for the 870 range and even earlier models like the Stylus Color 740. The error is indicated on these printers by all four lights on the printer flashing. Even if you press the power switch on the printer, the lights continue to flash, and the printer does not turn off!

1. Turn off your printer, ensuring that the print head is at it's home location and locked in place as normal;
2. Power off the printer at the wall or by removing the power cable, for at least 20 seconds;
3. When you restore power to the printer at the wall socket or by reinserting the cable, if the lights come back on straight away, the printer's power switch was 'on' - switch it off and return to step 1;
4. Hold down the paper-feed button and the button with the ink-drops next to it, and then turn on the printer, still holding the buttons down;
5. When the paper-out LED flashes, release the buttons;
6. Press and hold the Cleaning button, until several lights flash - this will take a few seconds (i.e. then release the button);
7. The printer will now attempt to reset, including resetting the EEPROM memory and running a short (about 10 seconds) cleaning cycle.

Procedure 2

1. Turn off your printer, ensuring that the print head is at it's home location and locked in place as normal;
2. Hold down the paper feed button only;
3. Turn on the printer;
4. As the paper feed light starts flashing, release the button;
5. Immediately hold down the ink-drops button for some 10-20 seconds or until the printer springs into life;
6. Allow printer to complete it's processing, then turn off for a few seconds, and back on again for a newly working printer!

Procedure 3 - for 1290 and possibly 890 printers 1290 printer with green (power / data) and red (ink / paper feed) lights flashing alternately:

1. Switch off printer with panel switch;
2. Switch off printer at mains switch - leave off for 20+ seconds;
3. Hold down roll feed and sheet feed buttons;
4. Switch on at mains;
5. Switch on at printer panel;
6. Continue to hold down roll and sheet feed buttons until both green and red lights flash together in synchronisation, not alternately;
7. Switch printer off and then, after a few seconds, on again at mains switch;
8. When red and green lights are both flashing in synchronisation, release the roll and sheet feed buttons;
9. Press and hold down the ROLL FEED button (the one at the extreme left) and keep it down until the machine finishes whirring, cleaning etc and the green light comes on steady;
10. Release the roll feed button and all should be well.

Depending on what type of printer you have:

Procedure 1 We found this procedure to work for the Stylus Photo 1270 type printer, and understand that it also works for the 870 range and even earlier models like the Stylus Color 740. The error is indicated on these printers by all four lights on the printer flashing. Even if you press the power switch on the printer, the lights continue to flash, and the printer does not turn off!

1. Turn off your printer, ensuring that the print head is at it's home location and locked in place as normal;
2. Power off the printer at the wall or by removing the power cable, for at least 20 seconds;
3. When you restore power to the printer at the wall socket or by reinserting the cable, if the lights come back on straight away, the printer's power switch was 'on' - switch it off and return to step 1;
4. Hold down the paper-feed button and the button with the ink-drops next to it, and then turn on the printer, still holding the buttons down;
5. When the paper-out LED flashes, release the buttons;
6. Press and hold the Cleaning button, until several lights flash - this will take a few seconds (i.e. then release the button);
7. The printer will now attempt to reset, including resetting the EEPROM memory and running a short (about 10 seconds) cleaning cycle.

Procedure 2

1. Turn off your printer, ensuring that the print head is at it's home location and locked in place as normal;
2. Hold down the paper feed button only;
3. Turn on the printer;
4. As the paper feed light starts flashing, release the button;
5. Immediately hold down the ink-drops button for some 10-20 seconds or until the printer springs into life;
6. Allow printer to complete it's processing, then turn off for a few seconds, and back on again for a newly working printer!

Procedure 3 - for 1290 and possibly 890 printers 1290 printer with green (power / data) and red (ink / paper feed) lights flashing alternately:

1. Switch off printer with panel switch;
2. Switch off printer at mains switch - leave off for 20+ seconds;
3. Hold down roll feed and sheet feed buttons;
4. Switch on at mains;
5. Switch on at printer panel;
6. Continue to hold down roll and sheet feed buttons until both green and red lights flash together in synchronisation, not alternately;
7. Switch printer off and then, after a few seconds, on again at mains switch;
8. When red and green lights are both flashing in synchronisation, release the roll and sheet feed buttons;
9. Press and hold down the ROLL FEED button (the one at the extreme left) and keep it down until the machine finishes whirring, cleaning etc and the green light comes on steady;
10. Release the roll feed button and all should be well.

To change from "page mode" (protrait) to "line mode" (landscape) you need to complete the following steps.
1. turn the power off
2. hold the feed button down
3. turn power on, the feed button should blink, release the button.
4. when the feed button blinks green, press and hold until it turns red or amber. release the button.
5. turn the power off.
6. hold down the feed button and turn power on, the button should blink and release. it will now print a calibration page. 4 blanks followerd by 2 text pages, the last saying "Now in DUMP" press feed to exit. on the first print, the 4th line down will say either page mode or line mode.

Check your user manual for resetting the printer to factory default settings.

If that doesn't work, unplug your printer from the computer and uninstall your software through Add/Remove Hardware. Shut down your computer and reboot. Reinstall your printer software, following the instructions carefully.

This should clear up your problem.
Let me know if you still are having problems. :)

First thing you need to check power is coming to printer or not.
If power is coming check printer is feeding properly or not when you press feed button it should feed one blank label.
If it does not feed label then calibrate printer from driver or press feed button and switch on printer hold feed button for 2-3 seconds and leave it .It will calibrate and print test page.

Thanks for the response. It turned out to be a faulty power supply which did not send enough power to turn the printer. now it works like a champ

what is the printer brand and model#? also try making sure the paper is in far enough and isn't sticking, and the paper guide is tight

hope this helps