<!-- from fixya rte -->How do I solve F1 code problem - Whirlpool 24 in. ADP5966 Free-standing Dishwasher

All questions need FULL 'year make model' as the first 3 words in all questions, or we guess.

The FI light is the equivalent of a CEL in your car. The ECU has detected an abnormality with one of the sensors, check the code and see what's up. Yes what he said...you will need a service manual to guide you through it.
Jun 18, 2012

Why is my FI light coming on during riding? - Wrist Twisters

wristtwisters.com https://www.wristtwisters.com > ... > Bikes

SOLVED: What does the f1 light mean my bike wont run that

Fixya https://www.fixya.com > motorcycles > t24308805-f1...
Nov 20, 2019 - The F1 light is the FI fuel injection light. Your bike needs to be diagnosed and scanned by your dealer or trusted mechanic. There is a problem with your fuel ...

SOLVED: F1 light comes on bike runs fine
Nov 20, 2019
SOLVED: F1 light comes on, bike dies. Is it air filter,
Feb 25, 2010
SOLVED: F1 light comes on bike cuts off
Apr 11, 2010
More results from www.fixya.com

FI light comes on - bike won't start!

StromTrooper https://www.stromtrooper.com > threads > fi-light-com...
I tried to start the bike and the FI light came on (red light) and it said FI in the odometer gauge. The bike would turn over but wouldn't start. It's done ...

Hello & Welcome to FixYa

Error code F1 is displayed due to electronic oven control failure and the only way to solve this problem is by replacing the control board which is bad. Sorry for the bad news but hope you understand... Please get back to me if you have any other questions.

Kevin

Hi

F1 Error indicates a bad control board and the control board (electronic control) should be replaced to solve this issue. Hope this helps...please post back for further assistance.

Daniel

F1 - E1
EEPROM checksum error

1.
Disconnect power for at least 30 seconds.
2. Re-apply power and observe for
at least one minute.
3. If code re-appears, replace control board (also
called ERC or clock).

Note: Applies to all F1-E...
codes except F1-E3.

Hello & Welcome to FixYa

Error code F1 is displayed due to electronic oven control failure and the only way to solve this problem is by replacing the control board which is bad. Please get back to me if you have any other questions.

Kevin

Hi,


The reason for F1 fault code in your dishwasher is due to the flood switch that has been activated in your unit. The best way to solve your problem is to turn off the water supply and power supply to your unit and call an authorized service center. These problems cant be fixed on your own.

Thank you !!

good day,
hope this link below will solve your problem.

kitchen appliances

Hi Van,
Happy to help you!

Go online to www.Frigidaire .com and you can enter your model #
and download the manual.
But I think that this problem will be solved only by service!
A & E factory service is good and nation wide!
1-800-905-9505
They answer 24/7
Thank you Neil

PS.Please do not forget to give me a problem solved rating

This code is in responce to a fault/failure in the lower keypad assembly. It is possible the keypad was bumped.

Maytag Gemini fault codes.
Fault code Suspect area Fault code Suspect area
F0 - 0 None
F1 - 1 Runaway cook upper oven
F1 - 2 Runaway cook lower oven
F1 - 3 Runaway clean upper oven
F1 - 4 Runaway clean lower oven
F1 - 5 Keypad cancel upper
F1 - 6 Keypad cancel lower
F1 - 7 Keypad disconnected
F1 - 8 Keypad shorted
F1 - 9 Slave