Question about Mitsubishi VS-50111 50" Rear Projection Television

1 Answer

On my vs 50111 my power button stopped working about 6 weeks ago but i used the remote however now i plu it in and the reen light comes on indicating power but then shuts off right after. it seemed to

Tried unpluin and replugin tried to et an error code dionostic with no luck checked power chord & connectin plug at the end where it actually connects to the set seemed rather loose not sure whats what

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 115 Answers

It could be a simple loose or broken wire,so
take back off and check it.Make sure unplugged first.
Could also be plug end.I have this with our Samsung,
but push the remote two to three times and it stays on.
LUCK

Posted on Sep 25, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1153 Answers

SOURCE: TV turns off right away relay clicks

1. MAY BE INTERMITTENT, SELF-DIAGNOSIS ERROR 23 OR 24. CHECK SOLDER CONNECTIONS AT CONNECTOR "DY" ON THE YOKES. 2. SHUTDOWN AT POWER WITH SELF-DIAGNOSIS ERROR 23 OR 24. CHECK C411 2200 UFD 35 V AND C412 10 UFD 50 V, BOTH LOCATED ON THE MAIN PCB.

Posted on Aug 27, 2007

  • 1 Answer

SOURCE: Mitsubishi HDTV 1080 WS-55859. Error Code 12

Did you push in the device and the menu buttons at the same time and get the error code...  I have the same problem and I get a 1,2 code....   I am looking for what the codes stand for...
Have you got any help on this....
Scott
mu email is smartin38@verizon.net

Posted on Oct 09, 2008

localwonder
  • 6784 Answers

SOURCE: WD 52525

This is a sign of a failing capacitor set on the power board. there may have been a small or minimal pulse that went threw the set during the power outage and when the power was restored. this could also be overheating as well due to dust forming on the power boards components. i would remove the back cover and clean as much dust off the power board as possible with some sort of canned air if possible. make sure the cooling system is working properly as well.

please rate and god bless.

Posted on Mar 16, 2009

  • 12 Answers

SOURCE: My Mitsubishi WS-65511 won't turn on.

I have had my WS-65511 fail like this, first at 4 years, second 2 weeks later, then 3rd time yesterday (4/14/2009). In past, the tech replaced a thermal sensor p/n 299P313010A (but Mitsubishi says that part is not for WS-65511 and that it does not have a thermal sensor - go figure). It is a white rectangle with about 30 pins in 2 rows and is soldered onto a board in the TV. List price is about $25. Might be your problem.

Posted on Apr 15, 2009

  • 668 Answers

SOURCE: I own a Mitsubishi HD 1080 series HD TV;

I believe it is going to be a major repair and I would hesitate to invest much money into it. I think the age of this set is older than 5 years. The VS model series were manufactures before the WS model series and they have been around for 8 years or so. Never the less, parts availability is getting tougher. If your pain thresh hold is 300.00 or 400.00
go for it. If not, check out new sets.
Hope this helps,
Sky Assoc

Posted on Oct 22, 2009

Testimonial: "Thank you very much for the advice. I agree it may more cost effective to "bite the bullet" and buy a new TV."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Mitsubishi parental lock removal/v-lock redo


Models:

Color Televisions
CS-20EX1, CS-20301, CS-26EX1, CS-26201, CS-26301, CS-2725R, CS-27EX1,
CS-27MX1, CS-27TX1, CS-27200, CS-27201, CS-27301, CK-27304, CK-27306,
CS-27401, CS-27403, CS-3135R, CK-3136R, CS-31AX1, CS-31FX1, CS-31MX1,
CK-31MX2, CS-31301, CK-31302, CS-3525R, CK-3526R, CK-3527R, CS-3535R,
CK-3536R, CS-35X7, CS-35AX1, CS-35FX1, CK-35FX2, CS-35MX1, CK-35MX2,
CK-35MX3, CS-35201, CS-35201A, CS-35203, CS-35205A, CS-35301, CS-35401,
CK-35402, CS-40FX1

Projection Televisions
VS-40VA2, VS-4517S, VS-45VA1, VS-45VA2, VS-4561, VS-4562, VS-5016R,
VS-5017S, VS-50VA1, VS-50VA2, VS-50VF1, VS-50VF2, VS-50VX2, VS-50VX3,
VS-5061, VS-5062, VS-6017R, VS-6026R, VS-60VA2, VS-60VF1, VS-60VF2,
VS-60VX2, VS-60VX3, VS-6061, VS-7017R

This system locks only the entire TV. The TV will display a screen that
will indicate "Parental Lock ... Now the lock is on" and request the
personal four digit code when the TV is powered on.

IMPORTANT> You must use the original remote control that came with the
TV to release the Parental Lock, you cannot use a remote
that came with a VCR, Audio System or from any other
manufacturer.

1. Depending on which remote came with your TV, press the button at
the top labeled TV,OR set the TV/VCR switch in the upper left
corner of the remote to the TV position. .

2. Press the button on the remote labeled POWER.
The TV will turn on and display an information
screen that indicates "Parental Lock ... Now the
lock is on" and ask for the four digit personal code.

3. Press the #9 and the QV buttons at the same time.
The TV will turn on.

4. Press the button labeled MENU.
The "TV Main Menu" will be displayed.

5. Press the ADJUST UP or DOWN button to move the arrow next to the
"Advanced Features" selection and then press ENTER.

The "Advanced Features" menu will appear and
indicate that the lock is ON.

6. Press the ADJUST button to move the arrow next to the "Parental
Lock" option, and then press ENTER.
The screen will change to indicate "Parental Lock
... Now the lock is on" and ask for the four digit
personal code.

7. Press the #9 and QV buttons at the same time.
The screen will return to the "Advanced Features"
menu and indicate that the lock is off.

8. Press the MENU button twice to return to normal viewing.

The original lock code has now been erased and the lock canceled.

on May 16, 2010 | Audio Players & Recorders

1 Answer

Motor will not come on everyday. comes on some days and then others, you have to start it manually. Replaced control panel 6 weeks ago and worked fine, now same problem again. Motor runs at lowest speed...


FIRST: When you shut the breaker off and then back on was it because the breaker was "tripped" ?

SECOND: Does the motor run "hot"? Feel the outside of the motor casing when its running to check. ****becareful - it may be really hot****

As soon as you get back to me with the information I can tell you what is going on and what direction to go in. Thank's

Dec 08, 2010 | Pentair IntelliFlo VS-3050 & VS+SVRS...

1 Answer

Mitsubishi VS-50111 Tv does not stay on.Turn Tv on and shuts off after a few seconds.


Mitsubishi VS-50111 Tv does not stay on.Turn Tv on and shuts off after a few seconds.

Aug 06, 2010 | Mitsubishi VS-50111 50" Rear Projection...

1 Answer

Need to program my tv and dvd player to the remote


Hi,

Please follow the steps below

Program the First Device by Entering Direct Codes

1.Turn all of your devices off, and then manually turn on the device you want to program.
2.Press the Setup button on your the universal remote and continue to hold it down until the indicator light stops flashing and remains solid.
3.Release the Setup button
4.Press the TV button.
5.Release it immediately and make sure the indicator light is illuminated.
6.Enter the first possible four-digit code on the universal remote, and then press another button on the remote to see if the device is now programmed, such as the volume control or power button.
7.If the device responds, you have successfully programmed your Philips universal remote.
8.If not, turn the device off and back on and follow the steps again using the next code on the list. Repeat until the device successfully responds.

How to Program a Remote Using Code Search
1.Turn all of your devices off, and then manually turn on the device you want to program.
2.Press the Setup button on your the universal remote and continue to hold it down until the indicator light stops flashing and remains solid.
3.Release the Setup button
4.Press the TV button.
5.Release it immediately and make sure the indicator light is illuminated.
6.Press either the Channel button or the Play button until the device responds. Each time you press the button, the Philips universal remote tries a new code.
7.When the code works, press the Mute button on the Philips universal remote and the code will be stored.


To get the universal remote codes please visit below solution

http://www.fixya.com/support/t5395701-universal_remote_code_phillips
Thanx

Jul 27, 2010 | Philips Universal PH301S Remote Control

1 Answer

Mitsubishi 50111


Run the diagnostics.

With the TV power cord plugged in, press the 'INPUT and 'MENU' buttons at the same time -- use the buttons on the front of the TV, NOT the buttons on the remote; a diagnostic Error Code Operational Check will begin, utilizing the 'POWER ON' LED (the green 'POWER ON' indicator light).

There will be a pattern of two sets of flashes, with a pause in bewteen flashes; this sequence of flashes will be repeated a total of five times.

The Error Code designations are listed below:

Error Code Description
12 No eror has occurred.
21 X-Ray Protect circuit.
22 Short Protect circuit.
23 Horizontal Deflection failure.
24 Vertical Deflection failure.

I hope this information helps.

Jun 17, 2009 | Mitsubishi VS-50111 50" Rear Projection...

2 Answers

2002 Mitsubishi VS-50111 Won't stay on


No you will need to search vancebaldwin, or Mcmelectronics, tritronics, any electronic online part store. RS does not carry it. Also there are fuses need to be changed also. More info at ctechnicians.com

Dec 18, 2007 | Mitsubishi VS-50111 50" Rear Projection...

2 Answers

Mitsubishi va-50111 television


You have to hold the menu button for about 8 seconds. You'll get a sign at the bottom of the screen that says "Front Panel Lock Disabled"

May 04, 2006 | Mitsubishi VS-50111 50" Rear Projection...

Not finding what you are looking for?
Mitsubishi VS-50111 50" Rear Projection Television Logo

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76099 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...