How do I stop Lights flashing

moved this post to toy trains.
TOY TRAIN

"This is an HO scale electric train, the fault is in the bachmann brand EZ COMMAND control"

Based on symptom and details, the control has detected a component failure. Since your model does not have digital display window in order to display a fault code, it will flash the four indicator lights of

Drying, Cool Down, Wrinkle Rid (Press Saver), and Clean Lint Filter will flash the number of times for the first digit of the code and the START indicator light will flash the number of times for the second digit.

Take separate counts of each indicator light, then repeat to confirm in order to be accurate in identifying the proper error code. The code is obtained by counting the number of times the lights flash. Example E24: The four indicator lights would flash twice indicating the 2 and the START indicator light will flash four times indicating the 4. The four indicator lights and the START indicator light

start flashing at the same time. The control will pause for 2 seconds, then repeat the code.

The failure is likely because of a faulty thermistor or because the heater is not working. It could have a broken heating element or a burnt wire connection at the control board. I would begin by accessing the thermistor and disconnecting it. The thermistor can be tested with an Ohm meter. The thermistor should measure approximately 50,000/5K Ohms at room temperature.

The heating element is located behind the drum and it can be disconnected and tested for continuity with an Ohm meter.

NOTE: Disconnect the dryer from the power supply before servicing.

My only guess would be that you disconnected the cable to the sensor while cleaning your Xbox. Have you checked all the connections before reassembling it? Check out the video I linked, maybe it'll help you!

Have you charged it? If you have plugged it in and no lights blink you may have a defective controller. If so check with Sony support/

Hi. Is a Fisher and Paykel scooter? While the lights are flashing, press the horn button. The lights will stop flashing and display a fixed pattern, this is the fault code. Once you have done this let me know what it is, and I will be able to tell you what the fault is.Neil.

Four lights around the power button flash red on your Xbox 360 console. Four flashing lights indicates that the console does not detect an audio/video (AV) cable.
Note Four flashing red lights will not appear on consoles that have both an AV port and an HDMI port.
Solution
http://support.microsoft.com/kb/906652

i just sync both of mine to my ps3 it was giving me difficult at first, but i noticed the when u first put in ur usb wireless thing it starts to blink really fast and when u push the p3 button on the controller twice it flashes really fast. so i took out the wireless usb thing then put it back in so the light on it would be flashing really fast like it was searching for somthing, then press the p3 button twice to make the lights flash really fast aswell so it will sync with it. Thats how i got both of my controllers synced we my ps3. the lights on on the wireless usb thing and the controller lights must be flashing fast at the same time to sync.

hold both the connection buttons on the consel and the controler untill it conectes. if it dosnt connect then your controller mit be damaged and cant remember the software for it. try to get a different controller to conect to it to see if it conects.

I had to pull the J3 connector off of the control module located just behind the dispenser panel. That eliminated the cycling and the flashing lights. Maytag guy came out and told me there is a control board located on the back of the refrigerator. Circuit board cost is $180 and installation labor another $300. I think because the refrigerator and freezer are still functional I will not repair this problem at this time.

I had the same problem, so I called customer service and had me do this:

1) with the USB cable plugged into the controller, power down the ps3 and turn the on/off switch in the back to "off".
2) hold your thumb down on the front button (where you normally can turn it on) while turning the switch on the back to "on" again. keep your thumb or finger on the front switch.
3) You will hear the normal "beep" that you usually hear when the PS3 boots up, but after a few seconds later, you will hear a secondary beep. Remove your thumb or finger after this second beep and the PS3 will reset itself after a few seconds. I have a projector connected to it, so I had to set the display screen back to HDMI afterwards, but when I disconnected the USB cable the controller worked wirelessly again. The customer service rep said that this allowed the controller to pair with the PS3 again. Note: You probably do not have to have the controller plugged into the USB cable at all while doing this. I just happened to have it plugged in. Hope this helps.