How do i reset the curcuit breaker on pront m51

Make sure the power draw on the AC doesn't exceed 3000 watts. 2300 running, 3000 surge watts. You may have an AC problem developing. The circuit breaker on the generator seems weaker when you reset it because of internal heat. Let the breaker cool a while before resetting.

There is no reset button on a M51 chair. Invacare puts fuses in the battery harnesses. The manual may say there is a reset but trust me there is not.

All moder fuel injected cars and trucks have an Impact switch in the fuel pump curcuit . which can trip if the veihcel is hit hard Ie run into by anothe car in parking lot. You also have a fuel pump relay in that fuel curcuit and usually a curcuit breaker which is self resetting and not a fuse. How ever if there is a fuse in that curcuit and the fuse has blown it will be out forever. Hope this is some help
Regards

It has a breaker but most of the time it's the main switch "driversdoor". The breaker will reset itself.

Turn off curcuit breaker. Mop up suds and water with towel. Remove kick panel mop up water here and dry out with a fan. Replace Kick Panel. Reset Curcuit breaker. Add one cup of Vingar to bottom of tub. Run a rinse and hold cycle. Repeat if necessary.

So this is how you remove the fuse that's underneath the machine, under the power button? Thanks!!

I don't know how technical you are so here are a few easy tests you can try:

plug a known, working lamp into each plug of the receptacle (top and bottom). This minimizes other potential issues.
Switch each circuit breaker FULLY off and then, Fully on. Yes, it is tedious but sometimes, breakers trip and it doesn't always show.
Still not working? Open up the cover plate and look at the contacts. You should have a black wire going to a gold colored screw and a white wire going to the other side, silver colored screw.

The best test you can conduct is using a simple voltmeter (AC) to test if you are getting voltage to the outlet. No AC Voltage? Try going to the known circuit breaker and measure the voltage coming from the known breaker while the other lead is on your neutral bus. Of course, if you aren't experienced with electricity, I recommend you get a licensed electrician to troubleshoot the issue.

As well, I know you mentioned that you tried resetting breakers but with a load on the circuit and someone else verifying it for you, you may just get lucky. More than likely, you will either encounter a faulty outlet, faulty wiring or a faulty breaker.

http://www.invacare.com/doc_files/1125085.pdf

Here's the manual. Locate battery cables follow them to the motor and Joystick. you'll see the reset button

It's possible that the first breaker that you said does not trip - it could be that breaker is failing to trip on a bad circuit. That is, it could be you have a bad circuit but that first breaker is not detecting it and pretends everything is OK. If your new breaker trips on the first breaker's circuit, the curcuit it probably bad and the breaker in not working properly. The most common problem for failed circuits is a stray ground wire in a box somewhere in the curcuit resting against a hot or neutral wire. You'll have to take apart every connection on that curcuit to find it. Not fun.

If it's tripping a breaker that usually means there is to high of an amp draw on that curcuit.

Are you plugging more things into that particular curciut (or just different but higher amp draw items) than you did last year?

It's also possible that one of the items plugged into that curcuit is wearing out and drawing more amps than before.

If you have an amp meter, plug everything back up just the way it was when you were having problems. Check the main wire going to that curcuit. (right at the breaker)

If your amp draw is greater or nearly the same as the amprating of that particular circuit, then thats your problem.
To many things/to high amp draw on one circuit.

If it is not near the amp rating, and you are getting proper voltage to the breaker, then I would replace that breaker.