Question about Powerware 9120 UPS System

1 Answer

Powerware 9120 batt disconnected

When i plug it in, it just says batt disconnected on the lcd screen, any ideas?

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 130 Answers

Hi Anonymous,
I want to help you with your question, but I need more information from you. Are the batteries new? If you did recently replace the batteries in the cartridge, did you check the connections and make sure contact as being made?

Let me know!

Daniel • daniel@psihq.com • Power & Systems Innovations • 800.260.2259 • www.psihq.com

Posted on Aug 25, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Powerware 9120 DC Bus Fault Problem.

there is a 100uf/63v capacitor near the IRF630 fet. You need to replace this in order to fix this error. Along there is also a 2200uf/16v capacitor. It is a good idea to change the both at the same time.

Posted on Feb 05, 2008

  • 198 Answers

SOURCE: Powerware 9120. 1500i UPS

You can download the manual and other literature at
http://www.powerware.com/EMEA/UPS/9120_info.asp

The contacts for support in India are found at
http://www.powerware.com/India/Service_Support/IN_Office_Contact.asp

They offer a battery monitoring software package, at
http://www.powerware.com/India/Service_Support/IN_Battery_Services.asp

You can email support at http://www.powerware.com/pp/Check.asp?key=code1
Good luck

Posted on Feb 23, 2008

  • 195 Answers

SOURCE: I have a Powerware 9120 2000 UPS battery failure message

Hi,

After you replaced the batteries did you perform a manual battery test?

If not do so.

Regards
Alan Hood
ami-man
UK

Posted on Mar 03, 2009

tech240
  • 169 Answers

SOURCE: when the machine is power on it show disconnect

There may be a broken batt lead or a failed cell or bloc inside.
try checking with software or


take out batts and test with meter.

if you dont understand how then get a tech to help. batts are dangerous.

Posted on Sep 15, 2009

  • 4 Answers

SOURCE: replacement fans for powerware 9120

9120 fans are rare and uncommon, for alternate solution just replaced the bearing of the fan.

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a powerware 9120 (6kva) and about 1 week i replaced all 20 batteries after the UPS failed. but its displaying battery disconnected when i try to power it. i cant seem to figure the problem. i tried...


Did your UPS display "Battery disconnected" or did it display "Battery Failure"? If it was "Battery Failure", for some reason the Powerware 9120 will take almost 18 hours after plugging in to power after battery replacement to correct the Battery Failure indication. Charger has to charge up the batteries, followed by an automatic battery test by the UPS. If the indication was "Battery Disconnected", you will need to check the internal fuses to see if they are blown. If the UPS keeps blowing fuses, it will require a board repair.

Jun 12, 2011 | Powerware 9120 UPS System

2 Answers

Short backup time


Suspect battery failure/faulty cell in a batt
Remove batts and check outside unit
charge up to around 2.27V/cell then check discharge on each batt (12V car lamp is good dummy load)
faulty one will be obvious.

MAKE SURE YOU ARE VERY CAREFUL WITH BATTERIES, THEY ARE VERY DANGEROUS, AND ALWAYS LIVE!

Check you manual for safety procedures, BEFORE working on Batteries.


hope this helps

thanks for using Fixya

Jul 06, 2010 | Powerware 9120 UPS System

2 Answers

Replacement fans for powerware 9120


A good electronics supplier should have. Get the correct voltage and size, and get one with the largest CFM available.

Oct 01, 2009 | Powerware 9120 UPS System

1 Answer

When the machine is power on it show disconnect battery powerware 9120 2kva


There may be a broken batt lead or a failed cell or bloc inside.
try checking with software or


take out batts and test with meter.

if you dont understand how then get a tech to help. batts are dangerous.

Sep 13, 2009 | Powerware 9120 UPS System

2 Answers

My ups has is faulty i need a circuit diagram to fix it


I had a DC bus fault error displayed.

So I unplugged battery, then turned on UPS. It said Batt disconnected of course.

So when I plugged in the batt while the UPS was on, and held the power button for a few sec, the UPS displayed Batt testing.

After a few moments it was back online and had no faults!

Worth a shot.

May 20, 2009 | Powerware 9120 UPS System

1 Answer

Powerware 9120 UPS


yes..and that happens after a period of time. When you get new ones, check the instructions on the initial charge/discharge requirements, and use those methods. tends to help with the battery life extension.

Jun 16, 2008 | Powerware PowerRite Plus UPS System

Not finding what you are looking for?
Powerware 9120 UPS System Logo

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top Powerware Computers & Internet Experts

Marvin
Marvin

Level 3 Expert

84625 Answers

geekyshrink
geekyshrink

Level 1 Expert

43 Answers

B.Th. Pluijm
B.Th. Pluijm

Level 3 Expert

558 Answers

Are you a Powerware Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...