Office Equipment & Supplies Logo

Related Topics:

A
Anonymous Posted on Aug 15, 2014

Recalibrate a printer - Konica Minolta Office Equipment & Supplies

1 Answer

Konica Minolta Error Codes and Solutions

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

  • Expert 210 Answers
  • Posted on Aug 21, 2014
Konica Minolta Error Codes and Solutions
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Joined: Aug 23, 2009
Answers
210
Questions
0
Helped
153620
Points
393

Can you tell us the model name of the printer? The calibration is different from machine to machine.
---------------------------------------------------------------
Konica Minolta Error Codes & Solutions - http://www.kmcodes.com
Drum, Transfer Belt and Fusing Unit Firmware Reset - http://www.bizhubreset.com
Drum and Toner Chip Reset - http://www.chipreset.eu
Transfer Belt and Fusing Unit Reset Kit - http://www.resetkit.eu

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My dell 5110 is recalabrating after every sheet when I am printing duplex postcards

U HAVE 2 print the postage stamp first u dont no how to use a printer i guess. its ok.

call samprt to help you mabe? idk
0helpful
1answer

Recalibrating my Konica Minolta bizhub 250

What do you want to recalibrate. have recently had the Developer and drum changed? Bizhub 250 is good machine adjusting the gray scale is printing out the Go to admin setting printer setting ,test prints print's a gray scale and bird picture along lazy brown fox saying.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

Recalibrating bizhub 250

What do you wan to recalibrate a Bizhub 250 B/W machine????

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

My printer is not printing everything. What is

If you are getting blank printouts try the ff:

Recalibrate the Printer
Recalibrate the Media Sensor of the printer by pressing photo and cancel buttons simultaneously make sure to load one piece of 8.5x11 normal white paper
Print demo page
If the printout is still blank call the technical support with the number 18004216699

Hope this will help

Thanks
Byron
0helpful
1answer

RX560 photos smudged

Try to recalibrate the printer, it is provided with the installation CD came with it. OR you can also try to look for recalibration in the control panel printers. Make sure that your cartridges are not short of ink. Sometimes there is an option of alignment. These things should help you out.

Thanks.

Do rate me if my help is helpful to you.

Thanks again
1helpful
2answers

It shows flashing red light for both black and color ink and a flashing E...but I have replaced both inks....still won't reset and allow me to print

The flashing E may mean you might need to recalibrate the printer. Put a sheet of paper in and press the Continue or Resume button on the printer and see if it will recalibrate. If not, unplug the printer from the electric outlet, wait about 10 seconds, plug it back in and see if that works.
0helpful
1answer

Printer head replacement

Hello junebug88,

Yes you need to recalibrate the printer after replacing the printhead. If it's a 5100 printer just press the "Photo" and the "Copy" button at the same time. It will calibrate the printer and after that you need to put the calibrated paper into the scanner glass and press start to start the media calibration sensor.

I hope I have been some of help... Take care.
0helpful
1answer

Plotter needs recalibration

You need to enter the service calibrations menu, to do this select the set up menu, once inside the set up menu press the up arrow & enter keys together. This will take you to the service tools menu, from here select service calibrations (printhead alignment and colour calibration are both in this menu). If you still here problems after you have calibrated your machine or the calibration fail replace the printheads.
0helpful
1answer

Won't print

nope..did you recalibrate the print heads after refilling the tank? Check the oil too? just kidding on the oil...usually after refilling, recalibration is recommended.
Not finding what you are looking for?

95 views

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman Weimar
Norman Weimar

Level 3 Expert

7035 Answers

Cindy Wells

Level 3 Expert

6688 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...