Question about Toro Lawnmower 20099 Mower Mowers Lawn

Open Question

How to replace traction contro cable part no 99-1586

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Toyota taca access abs light on Cruse light blinks traction light on.how to fix


Hi William the ABS and cruise contro are both linked it could be a wheel speed sensor or a damaged active bearing. The best way to be sure is to get it plugged in to diagnose correctly. Regards Jim...

May 17, 2015 | 2010 Toyota Tacoma

1 Answer

How is the traction cable adjusted on Toro Model 20027, Serial # 20005663. I'm replacing the cable and the new one is slightly different from the old one, but the Toro shop tells me it's the proper...


There is a large black plastic nut at the end where the cable attaches to the mower transmission. Turning it clockwise tightens the cable (engaging traction bar is tighter) and counter-clockwise is loosening the drive. If the cable is a little too long, you have to tighten it more.

Sep 27, 2017 | Toro Power Lawn Mower

1 Answer

Abs light, traction fault light on, radio does not operate


THE 1ST THING TO CHECK I BOTH SPEED CONTROL SENSORS LOCATED ON THE BACK SIDE OF YOUR WHEEL HUB...SOMETIMES THEY CAN BE CLEANED..TRUN WHEEL HARD RIGHT FOR RIGHT CABLE HARD LEFT FOR LEFT CABLE...PULL PIN OUT THEN CABLE VERY EASY TO REPLACE

Apr 12, 2014 | 2000 Jaguar S-Type

1 Answer

Me enciende la luz del ABS Junto al la luz del sistema del contro de Traccion (STC).


you have a bad wheel sensor you must get it scanned to find out which one it is.abs and traction control use the same information from the wheel sensors.

Nov 25, 2010 | 2001 Volvo S60

1 Answer

How do you replace a drive cable on a toro recycler 6.5 hp.


Its a bit of a pain - but with ordinary tools, it can be done. Get the replacement cable first. You can see how the bottom spring wraps around the cable with a universal joint sort of arrangement. Remove the belt protector (three screws from the top deck; if you have a battery compartment, that will temporarily need to go. Release the old cable from the top and middle attachment points, then unhook the spring from the traction lever. You might need to destroy the old cable lock to the mower deck to remove the old cable. Remove the plastic cup next to the cable where it exits the mower deck. Replace parts in this order: New spring/cable to the traction lever, snap in plastic interface to mower deck, small plastic cup top cable attachment, then middle attachment. You might need to move the middle attachment after you give it a test run. Replace belt cover and battery compartment if necessary. A lot of steps but, except for a difficult fit to get the spring hooked up, nothing is really difficult. I paid about $30 for the replacement cable from a local dealer; Overpriced, but I wanted to get the job done today.

Oct 15, 2010 | Toro Lawn Mower With Toro Power Tools

1 Answer

Why does my abs and traction contro light stay on


one of the wheel censors mite need to be replaced or the module under the hood may need to be

Apr 10, 2010 | 2003 Chevrolet Impala

1 Answer

Can a traction clutch cable on an Ariens 520 be repaired/replaced as a do it yourself? IF so, how do you repair it?


Yes, it can be replaced. Normally, cables are attached to the handles and then to the engagement bar for traction near the belts. You may need to tip the unit on it's nose to remove access panel to expose mechanisms. Also the inspection cover over the belts in front of the engine may help identify the cable routing

I’m happy to assist further over the phone at https://www.6ya.com/expert/rolandw_c013176d62ee17ae

Dec 21, 2009 | Ariens Garden

1 Answer

Traction Belt (new) continues to slip off of drive plate.


Sounds like you may need to replace the pulley as well. It has likely worn out of specification.

I recommend that you contact your nearest authorized service center, or contact Toro directly for assistance.

I trust this information proves useful.



helpful-uszrzov2vpx0k2p2rdejuao1-1-0_3.png

Oct 02, 2009 | Agri-Fab Agri - Fab Snow Blower - 42"

1 Answer

Cable traction needs adjusted


To adjust the self propel cable, loosen the cable
clamp, pull the cable downward to remove all the slack
then push the cable jacket up 1/8”
and secure with the cable clamp
good luck

Jan 26, 2009 | Toro Lawn Mower With Toro Power Tools

1 Answer

Replacing traction cable


Go to toro.com then customer care then manuals and parts type in model then find owners manual to download.

Jan 22, 2009 | Toro Lawn Mower With Toro Power Tools

Not finding what you are looking for?
Toro Lawnmower 20099 Mower Mowers Lawn Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toro Garden Experts

Joseph Mueller
Joseph Mueller

Level 2 Expert

346 Answers

lnbn1975

Level 2 Expert

204 Answers

roeb

Level 3 Expert

819 Answers

Are you a Toro Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...