Hy can't I receive Gems TV channel 43 on two TV's - all other programs are OK?

Hm..
So you want to connect your receiver thing to your tv ?
or your cable ?

Well if the antenna cable is hooked up, you should be able to simply run it up behind your tv and put it on the antenna plug.

The reveiver should attach to your tv with a cable provided.

where did you buy the tv, might not the same broadcast signal in your location. by the way have you been tried to have manual fine tune of any local channel or auto search so you can get available channel in the area.

You can often find the digital channel numbers for your local stations in a guide like http://www.titantv.com/ or https://tvschedule.zap2it.com/?aid=gapzap . Alternately, check if the local stations websites offer a link to their schedule. This will usually list the channel/channel digital identity. Another source for the digital channel numbers are the antenna choice/position/direction guides. Look at http://www.antennaweb.org or http://www.tvfool.com . Tvfool.com gives the direction and signal strength for all channel transmitters in your general area. Antennaweb.org is much more conservative and will only give the strongest stations in your area. That conservative list assumes an external antenna and clear path between the transmitter and your antenna.

In my area, the analog channel 7 became digital channel 7-1 . However, the channels 12 and 16 now transmit at 43-1 and 46-1 . However, after letting the TV do the auto-search, they are 12-1 and 16-1 when I type in the channel numbers on my remote.

I hope this helps. I might be able to provide a list of your local digital channels if you add a comment with your general location.

Cindy Wells

Hello
First of all reset the TV. for that

press and hold the POWER button
on the TV control panel for 5 or more seconds to reset the TV.
Then connect the TV tt any source like outdoor areiel or cable box etc, select the appropriate input, and retune the TV. First of all, connect it to an external antenna, and set it to autotune.

• You must configure the ANT/CABLE input source before

programming channels (-left-hand column).

• If the ANT/CABLE input signal type is set to Cable, the

automatic channel programming process erases channels

that were previously programmed into the TV's memory.

• If the ANT/CABLE input signal type is set to Antenna, the

automatic channel programming process adds newly found

channels to the existing set of programmed channels (and

does NOT erase channels that were previously

programmed into the TV's memory.) To remove an Antenna

source channel from the memory, you must manually delete

it.

• To tune the TV to a channel not programmed in the channel

memory, you must use the Channel Number buttons on the

remote control.

• Programming channels when the ANT/CABLE input is

configured for Cable will take substantially longer than when

the antenna input is configured for Antenna. This is normal;

however, once channel programming is finished, you should

not have to repeat the programming process again unless
your Cable TV service lineup changes significantly.
Find out the received channels are clear or not. If they are clear, your TV is perfect, and the input device you connects ot the TV is faulty. OK.

Hello
You can autotune your Sony TV without a remote control. Fist connect it to an external antenna or cable whatever may be, to its antenna socket at the back side.

After you have finished connecting your TV, you can use Auto Program to set up your

channels. During Auto Program, the TV will automatically search for available channels and
program receivable channels.

[1] Press POWER button on the TV to turn it on. The Initial Setup screen appears.

[2] Press CH+ button on the remote control or on the TV front panel to start Auto Program, or press CH-- button to exit.

The Initial Setup screen appears each time you turn on the TV until you perform Auto Program.

To perform Auto Program again

1 Press"MENU" button on the front panel of your TV.
2 Press "RIGHT ARROW button to highlight Channel Menu.
2 Press DOWN ARROW BUTTON to highlight CABLE or ANTENNA AND PRESS [+} to select.

4 Press UP arrow or DOWN arrow to highlight On or Off according to how you connected your TV. Press [+] to select.

4 Press F or f to highlight On or Off according to how you connected your TV. Press to
select
5 Press DOWN arrow button to highlight Auto Program. Press [+]to search for channels
6 After Auto Program finishes, press MENU button to exit.
OK

Make sure the tv is set to "std cable". You can find this in the menu under antenna settings.

I carried my Westinghouse TV to the basement. Unplugged the antenna from the digital converter box and connected it to my digital TV. I then re-scanned for channels and found channel 9. After carrying the Westinghouse TV back upstairs, I connected the original set-up and tuned to channel 9 which was now showing on the screen as no signal. From that point I moved my VHF dipoles until I had located the correct position for reception. A little labor intensive, but I was fortunate to have another antenna that was receiving channel 9.

Hi there!
If you cannot receive all channels it may be a fault with the antenna or the tuner may be faulty. If you have a VCR, you can tune that into the TV first and then tune the VCR to see if you then receive all channels. If so, use the VCR position on the TV to view and select or change channels on the VCR only. Good Luck,JUS004

FIXED! LG DAT-250W INSTRUCTIONS: TURN OFF THE MAINS POWER AT THE WALL UNPLUG ANTENNA FROM THE BACK TURN POWER BACK ON AT THE WALL & START AS NORMAL IT WILL COME UP WITH "POOR SIGNAL" THEN WE FLICKED THROUGH THE CHANNELS & TURNED IT OFF AGAIN AT COMPONENT & AT THE WALL PLUG THE ANTENNA BACK IN TURN EVERYTHING BACK ON Note: **Just avoid the channel that keeps locking up** LG are aware of this issue