Can't find my right password.

Question edited for clarity.

Manually set time for Avaya IP Office

IP Office Assistance https://www.ipofficeassistance.com > manually-set-tim...
Feb 28, 2013 - Manually Setting the System Time in IP Office · The current system time is displayed. · Enter the new time using 24-hour clock format. Use the * ...

This sounds like an electrical 'short', a bad earth connection or a faulty sensor. The car will have shut down because the vehicle diagnostics have detected a problem that the system has listed as 'serious'. This is a 'Safe' or 'Limp Home' mode to protect the vehicle's engine and electronics.
You should get it scanned for Trouble codes as this is one of the easier ways to find electrical issues. Modern vehicles have a silly number of electronic sensors in them any of which can cause problems when they start to fail.
Unfortunately, unless you have your own OBD2 scanner you will have to pay for the diagnostic scan. Ask at 4 or 5 different places as the prices charged can be VERY different.
These trouble codes will give clues as to where the issue is likely to be. If you get the codes comment below and I'll try to help explain them.

If you want to reset your IP Camera to factory defaults, you can use the following 3 methods. After resetting the device you will lose all your settings except Client Settings.

Method 1:Hard reset/ By pressing the RESET button
Step 1- Keep the device powered on for at least 30 seconds to complete its normal startup.
Step 2- Find something like a pin to press the Reset button on the camera and hold it for 15 seconds to restore the settings to factory defaults.
Step 3- Afterwards release Reset button, and the camera will be restored to factory defaults after rebooting.
Note: Reboot process takes about 1 min, please be patient.

Method 2:By using Intelligent IP Installer
Step 1- Install the Intelligent IP Installer with the CD.
Step 2- Run the Intelligent IP Installer. Click Search to find your device.
Step 3- Select your Camera in UPnP device list, click Factory default on the right side.
Step 4- Type the username and password in the login page, the default username and password are both admin. Wait for the device to reboot.
If you changed the username and password before and forgot the username and password, you have to follow
Method 1, make a hard reset.
Note: Reboot process takes about 1 min, please be patient

Method 3:By using Web-based Utility (management page)
Step 1- Open the web browser and type the IP address of the IP Camera into the address bar, press Enter. If you have changed the default port number is 80, Then type the IP address of the camera: new port number into the address bar of web browser.
Step 2- Type the username and password in the login page, the default username and password are both admin. Then click OK to connect to the device.
Step 3- Click SETTING -> BASIC -> Initialize on the left side, and then click Factory default to reset this IP Camera to the factory default settings.
Step 4- Keep waiting until the progress bar shows completion.

Open the Start Menu, right-click on Network, and select Properties. The Network and Sharing Center opens...click on Manage network connections. Right-click on the network adapter you want to assign an IP address and click Properties. Highlight Internet Protocol Version 4 (TCP/IPv4) then click the Properties button.10 Nov 2013

How to Assign a Static IP Address in Windows 7, 8, 10, XP, or Vista

www.howtogeek.com/howto/.../how-to-assign-a-static-ip-address-in-xp-vista-or-window... HOW TO PUT MY IP ADDRESS IN Google Search

And the next some steps may help you to get rid of your problem
1. Right click on the .pst file name in your folder list.
2. Choose Properties (Data Files Properties in Outlook 2010/2013), then Advanced button.
3. Click Change Password button.
4. Type your password in the Old password field.
5. Leave the New password and Verify fields blank.
6. Click Ok and work your way back to Outlook.
This dialog is also accessible from File, Account Settings, Data File tab. Select the pst file and click Settings.

Also there is a Recovery Toolbox for Outlook Password
Tool is free-to-try, but as ultimate way, you may try it
http://www.outlookpassword.recoverytoolbox.com/

One more variant see here:- http://www.filerepairforum.com/forum/microsoft/microsoft-aa/outlook/1456-lost-pst-password-for-outlook-2003

Check the switch down by the gear shift lever, and the wiring to the switch, if one of the wires has come off the switch it will give problems.

Most likely the laser has failed and needs replaced. Here is the documentation.

CA1 Indicates that the polygon motor in the ROS has failed.
Procedure Enter output test, code 103, GP 10.
The polygon motor runs. Yes No Unanswered
Perform the following:

• Check the connector CN26 on the Interface PWB. Refer to Wiring Diagram 4.
  
• Check the harness and the pin connectors.
  
• Check the Interface PWB for damage.
  
• Install a new ROS, PL 9.10 Item 15.
  
• Install a new Interface PWB, PL 9.30 Item 5.
  

Check at connector CN26 pin 4 on the Interface PWB for a low signal. Refer to Wiring Diagram 4.
The signal is low. Yes No Unanswered
Perform the following:

• Check all the connectors to the interface PWB are pushed fully home.
  
• Check the interface PWB for damage.
  
• Install a new ROS, PL 9.10 Item 15.
  
• Install a new interface PWB, PL 9.30 Item 5.
  

Perform the following:

• Check all the connectors to the interface PWB are pushed fully home.
  
• Check the interface PWB for damage.
  
• Install a new interface PWB, PL 9.30 Item 5.
  

Well, to make a long story short, I finally unlocked my ipod after perilous hours of invalid guesses. What did I do? I have a habit of making obvious passwords-I simply goofed this time. I used the last four digits of my mother's cellphone number! Yes, yes, silly me silly me. However, I was quite relieved when I finally unlocked it. Thanks! =)

Belkin Routers can be accessed by typing the following IP address in the address bar of Internet Explorer: I will give you two alternatives as off the top of my head I cannot remember!! When you have typed in your IP address for the Router, you will then be asked for a username & password. Try these: Router IP 192.168.2.1 USERNAME admin Password password If the password does not work try admin or just leave it blank If this is not the right IP try 192.168.1.1 and follow the same Username/Password as suggested above. Hope this works for you.