Question about Universal MX-900 Remote Control

1 Answer

Why won't MX 900 turn on even after putting in new batteries

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 28 Answers

The obvious question here is: are the batteries installed the correct way? Here is a web page to download the operator manual:

http://www.universalremote.com/pdf/MX-900OwnerManual.pdf

Also; are your batteries good? are they making good contact? Has the remote been damaged by leaking batteries? Inspect and test.

Do you have the original remote controls for the devices you are trying to control? If so... do they work? Remember... they will need batteries too!

Are there manual switches on the device you want to control? Do they work? Can you turn it on and off?

We are moving through a process to identify which items work, which are good and which are faulty.

Posted on Jul 20, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Genesis mx 900


Your remote needs to be cleaned internally.

Aug 31, 2014 | Universal Remote Universal Genesis Remote...

1 Answer

Mx-900 wasn't switching channels. Tried new batteries but it is now reading loader. is there a way to get back to normal operation


Try removing the batteries, then short out the terminals in the remote. This should discharge any residual power in the components in the remote. Re insert the batteries and it should then work ok

Aug 06, 2014 | Universal MX-900 Remote Control

1 Answer

Why will the mx 900 not turn on even with new batteries


You should set up the remote control with the set-up codes to your device brand.
Check the remote control for its infrared emission. Check it with fresh batteries. If you wish to get more details about how to check a remote control, please visit this site. One among the posts has details about it. Surf the site in "Mosaic" or "Magazine" view. It will make surf easier.
http://electronicshelponline.blogspot.com/
If remote control is found OK, and have infrared emission, set it up with your device by using the set-up codes.
If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes used for devices too are given, in the order of device brand name list in alphabetical order. Do a search by type in the brand name of your device, at its search box, and press "Enter". Or, pull up older posts.
http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/

Jul 19, 2014 | Universal MX-900 Remote Control

1 Answer

1993 Triumph Trophy 900 will not turn over


Hi, Anonymous before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. The electric starter is working but starter clutch has failed.
14. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
900 Trophy Won Start
What to do When Your Motorcycle Won Start
Triumph Trophy Service Manual
http://www.triumphestore.com/
Triumph Trophy Handbook

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jun 21, 2017 | 1993 Triumph Trophy 900

1 Answer

My razor mx 500 motor won't turn.


I think you are talking about an electric motor on your bike . If the motor is New you may have a bad throttle switch . You can use an ohm meter to check the throttle switch . Connect the two leads of the ohm meter to the wires of the throttle switch ( dissconected) . As you turn the throttle the ohm reading should coraspond to how much you turn it .

Jan 15, 2018 | Razor MX500 Dirt Rocket

1 Answer

The brushes won't spin. I put new brushes on and it still doesn't spin.


Usually when the brushes won't turn it is due to a bad turbine. Insert a screwdriver into the square hole that the pin on the brush fits into, and see if it turns. If it is seized up, the turbine assembly will need to be replaced.

Jun 28, 2011 | Hoover SteamVac F5914-900 SpinScrub...

3 Answers

Where can I purchase a Lithium battery 046067 for an MX 3000?


Do you favorite search engine and type your model number and then batteries. What I got is www.buy.com

Aug 18, 2009 | Universal Remote Control MX-3000 LCD...

3 Answers

I can not get my MX-900 Universal Remote to connect to my compute


Turn off CPU, Unplug Power cable, And all usb devices, let it sit for about 20mins. Plug it all back in. Turn on the CPU! Also make sure if your device requires "DRIVERS" or if you have a CD download and install that before anything.

Nov 22, 2008 | Universal MX-900 Remote Control

1 Answer

MX-900 Universal Remote Control


you might want to reprogram it with different codes. it's a classic problem.

Oct 13, 2008 | Universal MX-900 Remote Control

Not finding what you are looking for?
Universal MX-900 Remote Control Logo

392 people viewed this question

Ask a Question

Usually answered in minutes!

Top Universal Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76140 Answers

JOHN TOPLISS

Level 2 Expert

180 Answers

Cindy Wells

Level 3 Expert

6031 Answers

Are you an Universal Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...