What does the code bad line mean

"bad line" error means the control panel is not seeing a proper voltage to the oven. Have the power connections checked with a voltmeter all the way to the control panel. If voltage is present, you may need a new control.

http://www.pcmag.com/encyclopedia/term/38515/beep-codes

here are the beeping explaned
two beeps,means bad memory.

Have you Googled the beep codes? This is most likely your solution. You should do the RAM test on your system.


Blue Screen Of Death

• Remove all USB attached devices.
  
• You may need to roll back system with System Restore. Under Safe Mode (press F8 during boot and choose safe mode). Start > Search type System Restore. Now choose a date prior to problem. You may have to try a few dates.
  
• Uninstall last program(s) that was installed, again in safe mode.
  
• Test one DIMM at time. One slot at a time. To eliminate possible bad RAM. Unplug PC. Opening case. Remove all RAM. Use static precautions!
  
• Re-install Windows. Clean install works best. All data will be lost.
  
• Lastly you may have other hardware problems. If it does another blue screen after reloading windows, especially with a clean install.
  

Hello,
The F1 error code means a button on the touchpad is stuck,usually pushing clear/off will clear it. Since you have done that and it returns the touchpad needs to be replaced

Gene

You can check the meanings of the error beep codes HERE. Every beep code means something different. The bad thing is that the code I think you are speaking of is a fatal error.

Good luck

I don't understand the beep code you describe, but the 2850 has many beep codes to help understand what is going on.

First ... Identify the beep. Does the beep start as soon as you power it on, or after several seconds? What is the pattern of the beep - is it a repeating set of beeps - 3 sets of beeps between 1 and 4 beeps ... like 1 beep-3 beeps-2 beeps, or 3 beeps, 3 beeps, 1 beep? Or is it a steady repeating beep - about once per second?

Second ... is the LCD panel on the server blue or orange? If orange, what is the error code(s) it is scrolling?

If it is a steady, once-per-second beep, it is probably your RAID controller. Does the system boot to Windows/OS ok? If so, use (or install) OpenManage Server Administrator (Managed Node from Dell's Support Site) to check the Hardware Logs and check the RAID array (under Storage/Virtual Disks). If it is not booting to the OS, then go into CTRL-M to see what the status of your array is.

I think the graphics card has become unseated as the PC does not need a monitor to start up so there would be no beeps; Here is a list of beep codes with there meanings.
BEEP CODE MEANING POSSIBLE CAUSE
1 Beep (No video) Memory refresh failure Bad memory
2 Beeps Memory parity error Bad memory
3 Beeps Base 64K mem failure Bad memory
4 Beeps Timer not operational Bad motherboard
5 Beeps Processor error Bad processor
6 Beeps 8042 Gate A20 failure Bad CPU or Motherboard
7 Beeps Processor exception Bad processor
8 Beeps Video memory error Bad video card or memory
9 Beeps ROM checksum error Bad BIOS
10 Beeps CMOS checksum error Bad motherboard
11 Beeps Cache memory bad Bad CPU or motherboard

An F-1 error code on your model means the element was energized when it should not have been, A shorted interconnect harness or failed power relay board.

A probe indication could be a failed meat probe jack or bad harness in a unit that has one. In a unit without a meat probe, suspect a bad board.

Both conditions would warrant bringing in a tech.

Before you do, turn off the circuit breaker fot 3 miutes and turn it back on. This will reboot the boards. If problem persists, the call a service tech.

sound as if u got water in your controls which would cause the electronic clock assembly to short. unplug for 24 hrs to allow it to dry if the probelm coming back it eca is bad

If you need further help, reach me via phone at https://www.6ya.com/expert/marlon_56d9a24f02585258