How to reset the check valve - Weber Genesis Silver B Grill

There is no reset button for the compressor, if the compressor won't start check the valve is not open, also check the outlet power, Shut the drain valve at the bottom of the tank if it's open

the discharge valve is leaking replace it. good luck finding parts.

Several things to check. Check amp draw with meter to make sure that the reset is not bad. It amp meter is showing low amp draw when it trips, then replace reset. If reset is good check condition of the cold start valve. The valve will not allow pressure to build until motor is at full rpm and the pump is making good pressure/volume. If cold start valve does not close, check pump for leaking or broken reed valves. If cold start valve is good, check the capacitor for at least 10 percent of rated valve. Low pressure /volume is usually leaks from tubing or leaking /broken reed valves or burned gaskets in the head of the pump. Finally, make sure that the check valve or non-return valve is not leaking pressure from the tank causing back pressure. Good luck

reset the check valve -- we get a "grill will not get hot" call 5 - 6 times a week and 99 out of 100 need to reset the check valve. 3 minutes and it is fixed!

sounds like a bad check valve,or a bad bleeder .check your reset button ,usually red ,and reset it.start your compressor again.it should start.be sure you didnt trip your breaker first.air is comming out steady from the bleeder when the compressor stop pumping ,replace your check valve.hope this help!

replace thermistor

Several things to check. Amp draw to be within number on plate, if amp draw not correct check capacitor, should be within 5% of rating on cap.. If amp draw about right and cap reads good suspect faulty breaker. If amp draw high and cap. good check for leak at in-tank check valve. With pressure in tank remove hose at check valve spray soapy water. If check valve good, suspect reed valves leaking. If reeds are leaking the compressor will take longer than normal to fill and the discharge tube/air will get very hot. It is recommended to note the amount of time it takes to fill tank when unit is new and compare this as unit wears. Length of time to fill is an indication of how well unit is working. A combination of leaky valves and leaking fittings as well as leaking checkvalve will cause motor to overheat.

put a new BPT hose vacum line hose.

Vitally

its easy too replace but you need too reset your cmputer first too see if the light stays out before you go and buy the egr valve
disconnect the pos side of the battery for 5 min that will reset the computer,if the light comes back on then get the egr valve then you will have too reset it again

01 = Acquastop operated due to leak / overfill - machine drains until empty + lmin.

A02 = Heater Relay open circuit/short circuit or Thermistor or Safety T/Stat o/c or s/c or Element machine fills to Level Switch & Wash Pump runs.

A03 = Thermistor open circuit /short circuit - machine drains until Level Switch resets +1minute

A04 = Unable to sense/reach temperature in 70mins. - machine drains until Level Switch resets + lminute

A05 = Level Switch not resetting in within 3' 20" of drain commencing - machine drains until Level Switch resets +1 minute

A06 = Not used see also H20 at end

A07 = Wash pump Triac closed/open circuit - check that Drain Pump is not disconnected or Aquastop operated

A08 = Auxiliary Wash Pump Triac closedlopen circuit - check Wash Motor operation- machine drains until Level switch resets+30"

A09 = Main Wash Pump Triac closed/open circuit - cheek Wash Motor operation- machine drains until Level Switch resets+30"

A10 = Fill Solenoid valve Triac closedlopen circuit - check valve/operation - machine drains until Level Switch resets+30"

A11 = 1/2 load Solenoid Valve Triac or alternating Wash Motor action - check Solenoid Valve operation & alternating Motor action, replace Module if required - machine drains until Level Switch resets +30"

A12 = Relay with open circuit - check Heater, replace Module if required - machine drains until Level Switch resets+30"

A 13 = Dispenser Triac incorrect operation closed/open circuit - Wash Cycle completes but with Dispenser Lid notfunctioning correctly

H20 = Static 'Fill Time exceeding 6 minutes - cheek for blockages/low pressure