Need to replace the AC Power Adaptor for my Precor Elliptical 5.17i. Would ANY 12VDC 120VAC work? Where can I purchase? Thank you for your help.

welcome to USA, we use our own adapters here, 120vac and special plug AC side.
where do you live country.?
simpletech 320GB BOM No: 96200-41001-05
they sell them on ebay, why not look there and buy it.
output 12vdc 0.4 amps or MORE.
center pin must be + output end.

any pack 12vdc like above works, over 0.4amps.
and AC end correct and if you have 240vac make sure the pack does that too.

Ac adapters for PCs can be bought from most of the electronic spare part selling shops. http://electronicshelponline.blogspot.com/

Precor Error 30, 31, 32 and 33, Communications Error Probable Cause 1. Bad interconnect cable between upper PCA and lower PCA.
2. Interconnect cable is mistakenly plugged into the CSAFE connector at the upper PCA.
3. Elliptical 5.17 equipped with old software version 1.01 in upper and lower PCA.
4. Upper and lower PCAs have mismatched software.
5. Another component plugged onto the PCA is overloading the +5VDC power supply.
6. Bad lower PCA.
7. Bad upper PCA.
Corrective Action

1. Test unit with a know good interconnect cable or test the interconnect cable for continuity. Replace interconnect cable if necessary.
2. Disconnect the interconnect cable from the CSAFE connector and attach to the proper position on the upper PCA.3.
3. Replace the upper and lower software of the 5.17 elliptical with the most current versions.4.
4. If one of the PCAs is found to have software version 1.01, replace it with the most current software version.
5. Disconnect all components from the upper and lower PCA leaving the data cable connecting between the upper and lower PCAs and the AC power going to the lower PCA. If the unit shows any error other than the error 3x, reconnect components one at a time. Reset power between each newly connected component until the error 3x reappears. Whichever component was last connected when the error 3x reappears, is the cause for the error. Replace the faulty component.
6. Test unit with a known good lower PCA. Replace the lower PCA if necessary.
7. Test unit with a known good upper PCA. Replace the upper PCA if necessary.

Precor Error Code 30 31 32 33

Precor Error 46, Low Battery Voltage (AMT12 Only) Probable Cause 1. Blown fuse in the positive battery wire of the AMT12 2. Faulty or poor connection on the battery or LPCA 3. Low or no output voltage from battery
Corrective Action

1. Remove the power from the unit and move the lift fuse from the in line fuse holder on the positive battery cable
   • Measure the fuse with an ohm meter (multi meter), the fuse should read approximately 1 ohm or less
   • If the reading is significantly high, replace the fuse
   • If the fuse is open, refer to next solution before you continue
2. Check connector of the battery cable for shorts or poor connections
3. Enter the diagnostic program per procedure, P80 Settings or Accessing the P30 Diagnostic Software
   • Using the diagnostic program allows you to test the incline system without continuously pedaling the unit if you have an external power supply
   • Otherwise, you will need to continue to pedal the unit
   • Connect a DC voltmeter to the J3 connector on the lower PCA as follows:voltmeter common lead to terminal 3 (black wire) and voltmeter "hot" lead to terminal 2 (red wire)
   • Using the STRIDE HEIGHT Up and Down keys, operate the incline
     • The voltmeter should read about +12VDC when the incline is instructed to move upward and about -12VDC when incline is instructed to move downward
   • If either voltage measurement is significantly low, replace the battery

Precor Error 46 AMT12 Only Low Battery Voltage

Precor Error 29, Excessive AC Input Current Probable Cause 1. The running belt and/or deck are badly worn.
2. Bad lower PCA.
3. Drive motor is shorted or de-magnetized causing a high power demand.
Corrective Action

1. Check the amp draw using a clamp on AC volt-amp meter during loaded and no load conditions and compare values to a similar treadmill that is known to have a good running belt and deck. Replace the belt and/or deck if necessary. Don't forget, some units have a double sided deck which means it may be flipped over rather than replaced if it has an unused side.
2. Test unit with a known good lower PCA. Replace lower PCA if necessary.
3. Test unit with a known good drive motor. Replace drive motor if necessary.

Precor Error Code 29

Precor Error 30, 31, 32 and 33, Communications Error Probable Cause 1. Bad interconnect cable between upper PCA and lower PCA.
2. Interconnect cable is mistakenly plugged into the CSAFE connector at the upper PCA.
3. Elliptical 5.17 equipped with old software version 1.01 in upper and lower PCA.
4. Upper and lower PCAs have mismatched software.
5. Another component plugged onto the PCA is overloading the +5VDC power supply.
6. Bad lower PCA.
7. Bad upper PCA.
Corrective Action

1. Test unit with a know good interconnect cable or test the interconnect cable for continuity. Replace interconnect cable if necessary.
2. Disconnect the interconnect cable from the CSAFE connector and attach to the proper position on the upper PCA.3.
3. Replace the upper and lower software of the 5.17 elliptical with the most current versions.4.
4. If one of the PCAs is found to have software version 1.01, replace it with the most current software version.
5. Disconnect all components from the upper and lower PCA leaving the data cable connecting between the upper and lower PCAs and the AC power going to the lower PCA. If the unit shows any error other than the error 3x, reconnect components one at a time. Reset power between each newly connected component until the error 3x reappears. Whichever component was last connected when the error 3x reappears, is the cause for the error. Replace the faulty component.
6. Test unit with a known good lower PCA. Replace the lower PCA if necessary.
7. Test unit with a known good upper PCA. Replace the upper PCA if necessary.

Precor Error Code 30 31 32 33

Precor Error 30, 31, 32 and 33, Communications Error Probable Cause 1. Bad interconnect cable between upper PCA and lower PCA.
2. Interconnect cable is mistakenly plugged into the CSAFE connector at the upper PCA.
3. Elliptical 5.17 equipped with old software version 1.01 in upper and lower PCA.
4. Upper and lower PCAs have mismatched software.
5. Another component plugged onto the PCA is overloading the +5VDC power supply.
6. Bad lower PCA.
7. Bad upper PCA.
Corrective Action

1. Test unit with a know good interconnect cable or test the interconnect cable for continuity. Replace interconnect cable if necessary.
2. Disconnect the interconnect cable from the CSAFE connector and attach to the proper position on the upper PCA.3.
3. Replace the upper and lower software of the 5.17 elliptical with the most current versions.4.
4. If one of the PCAs is found to have software version 1.01, replace it with the most current software version.
5. Disconnect all components from the upper and lower PCA leaving the data cable connecting between the upper and lower PCAs and the AC power going to the lower PCA. If the unit shows any error other than the error 3x, reconnect components one at a time. Reset power between each newly connected component until the error 3x reappears. Whichever component was last connected when the error 3x reappears, is the cause for the error. Replace the faulty component.
6. Test unit with a known good lower PCA. Replace the lower PCA if necessary.
7. Test unit with a known good upper PCA. Replace the upper PCA if necessary.

Precor Error Code 30 31 32 33

Precor Error 30, 31, 32 and 33, Communications Error Probable Cause 1. Bad interconnect cable between upper PCA and lower PCA.
2. Interconnect cable is mistakenly plugged into the CSAFE connector at the upper PCA.
3. Elliptical 5.17 equipped with old software version 1.01 in upper and lower PCA.
4. Upper and lower PCAs have mismatched software.
5. Another component plugged onto the PCA is overloading the +5VDC power supply.
6. Bad lower PCA.
7. Bad upper PCA.
Corrective Action

1. Test unit with a know good interconnect cable or test the interconnect cable for continuity. Replace interconnect cable if necessary.
2. Disconnect the interconnect cable from the CSAFE connector and attach to the proper position on the upper PCA.3.
3. Replace the upper and lower software of the 5.17 elliptical with the most current versions.4.
4. If one of the PCAs is found to have software version 1.01, replace it with the most current software version.
5. Disconnect all components from the upper and lower PCA leaving the data cable connecting between the upper and lower PCAs and the AC power going to the lower PCA. If the unit shows any error other than the error 3x, reconnect components one at a time. Reset power between each newly connected component until the error 3x reappears. Whichever component was last connected when the error 3x reappears, is the cause for the error. Replace the faulty component.
6. Test unit with a known good lower PCA. Replace the lower PCA if necessary.
7. Test unit with a known good upper PCA. Replace the upper PCA if necessary.

Precor Error Code 30 31 32 33

You may have to purchase the belt from a Precor dealer in you area, if you don't have one then call Precor directly @ 1-800-347-4404 and they will help you. Most of these part have not hit the secondary market yet and Precor pretty much call the shots.

The battery is not fully charging to the 12v requirement their are a couple of screws that hold the side panels then rotate the panels counter-clockwise and they will come off. Take the battery leads off use a multi-meter the voltage on battery if it is below 12v then replace it. You may purchase this from a Precor dealer in you area if you don't have one then call Precor directly @ 1-800-347-4404 and they will help you.